3n-alt-xl710

40ge2p1xl710-ethip4ipsec10000tnlsw-ip4base-int-aes128cbc-hmac512sha-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to

umber of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG ode interfaces. Incrementing of IP.dst (IPv4 destination address) is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.15, 0.15, 0.15, 0.15, 0.15, 0.15, 0.15, 0.15, 0.15, 0.15] 

 1518b-2t2c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.26, 0.25, 0.26, 0.26, 0.25, 0.25, 0.26, 0.25, 0.25, 0.26] 

 1518b-4t4c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.45, 0.46, 0.46, 0.45, 0.45, 0.45, 0.45, 0.45, 0.46, 0.46] 

 imix-1t1c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.26, 0.27, 0.27, 0.27, 0.26, 0.27, 0.27, 0.27, 0.27, 0.27] 

 imix-2t2c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.42, 0.42, 0.43, 0.43, 0.42, 0.43, 0.43, 0.43, 0.42, 0.43] 

 imix-4t4c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.68, 0.68, 0.69, 0.68, 0.68, 0.68, 0.68, 0.68, 0.68, 0.69] 

40ge2p1xl710-ethip4ipsec10000tnlsw-ip4base-int-aes128gcm-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to

umber of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG ode interfaces. Incrementing of IP.dst (IPv4 destination address) is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-mrr

 [0.88, 0.89, 0.89, 0.89, 0.89, 0.89, 0.89, 0.89, 0.89, 0.89] 

 1518b-2t2c-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-mrr

 [1.59, 1.60, 1.60, 1.59, 1.59, 1.60, 1.59, 1.59, 1.59, 1.59] 

 1518b-4t4c-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-mrr

 [2.80, 2.81, 2.80, 2.80, 2.80, 2.80, 2.79, 2.80, 2.79, 2.80] 

 imix-1t1c-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-mrr

 [1.50, 1.51, 1.51, 1.51, 1.51, 1.51, 1.51, 1.51, 1.51, 1.51] 

 imix-2t2c-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-mrr

 [2.73, 2.75, 2.74, 2.74, 2.74, 2.74, 2.73, 2.75, 2.75, 2.74] 

 imix-4t4c-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-mrr

 [4.96, 4.98, 4.99, 4.99, 4.98, 4.97, 4.95, 4.97, 4.96, 5.01] 

40ge2p1xl710-ethip4ipsec10000tnlsw-ip4base-int-aes256gcm-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to

umber of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG ode interfaces. Incrementing of IP.dst (IPv4 destination address) is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-mrr

 [0.80, 0.81, 0.81, 0.81, 0.80, 0.81, 0.81, 0.81, 0.81, 0.80] 

 1518b-2t2c-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-mrr

 [1.48, 1.48, 1.48, 1.48, 1.48, 1.48, 1.48, 1.48, 1.48, 1.48] 

 1518b-4t4c-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-mrr

 [2.64, 2.65, 2.64, 2.64, 2.64, 2.63, 2.64, 2.63, 2.63, 2.64] 

 imix-1t1c-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-mrr

 [1.43, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44, 1.44] 

 imix-2t2c-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-mrr

 [2.58, 2.59, 2.59, 2.59, 2.58, 2.59, 2.59, 2.59, 2.59, 2.59] 

 imix-4t4c-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-mrr

 [4.62, 4.62, 4.62, 4.63, 4.61, 4.61, 4.63, 4.63, 4.62, 4.61] 

40ge2p1xl710-ethip4ipsec1000spe-cache-ip4base-policy-outbound-nocrypto-mrr

RFC4301: SPD lookup performance

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing, wo static IPv4 /24 route entries, one SPD on each outbound interface in each direction and 1000 SPD entry(ies) in each SPD. Only outbound traffic is matched and only the last rule is the matching

ule. SPD flow-cache for IPv4 outbound traffic is enabled. DUT1 is tested with Intel-XL710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. The DUT does SPD lookup with only he lowest priority rule matching the traffic. The action of the matching rule is BYPASS. No encryption or authentication is done.

  • [Ref] Applicable standard specifications: RFC4301 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec1000spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [6.21, 6.23, 6.22, 6.23, 6.23, 6.23, 6.22, 6.23, 6.20, 6.23] 

 64b-2t2c-ethip4ipsec1000spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [12.65, 12.66, 12.68, 12.69, 12.68, 12.71, 12.70, 12.70, 12.72, 12.70] 

 64b-4t4c-ethip4ipsec1000spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [25.26, 25.35, 25.37, 25.36, 25.35, 25.40, 25.34, 25.36, 25.33, 25.39] 

40ge2p1xl710-ethip4ipsec1000spe-ip4base-policy-outbound-nocrypto-mrr

RFC4301: SPD lookup performance

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing, wo static IPv4 /24 route entries, one SPD on each outbound interface in each direction and 1000 SPD entry(ies) in each SPD. Only outbound traffic is matched and only the last rule is the matching

ule. DUT1 tested with Intel-XL710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. The DUT does SPD lookup with only he lowest priority rule matching the traffic. The action of the matching rule is BYPASS. No encryption or authentication is done.

  • [Ref] Applicable standard specifications: RFC4301 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec1000spe-ip4base- 
policy-outbound-nocrypto-mrr

 [0.44, 0.44, 0.44, 0.44, 0.44, 0.44, 0.44, 0.44, 0.44, 0.44] 

 64b-2t2c-ethip4ipsec1000spe-ip4base- 
policy-outbound-nocrypto-mrr

 [0.87, 0.87, 0.87, 0.87, 0.87, 0.87, 0.87, 0.87, 0.87, 0.87] 

 64b-4t4c-ethip4ipsec1000spe-ip4base- 
policy-outbound-nocrypto-mrr

 [1.74, 1.74, 1.74, 1.74, 1.74, 1.74, 1.74, 1.74, 1.74, 1.74] 

40ge2p1xl710-ethip4ipsec1000tnlsw-ip4base-int-aes128cbc-hmac512sha-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to

umber of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG ode interfaces. Incrementing of IP.dst (IPv4 destination address) is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.15, 0.15, 0.15, 0.15, 0.15, 0.15, 0.15, 0.15, 0.15, 0.15] 

 1518b-2t2c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.26, 0.26, 0.26, 0.26, 0.26, 0.26, 0.26, 0.26, 0.26, 0.26] 

 1518b-4t4c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.48, 0.48, 0.48, 0.48, 0.48, 0.48, 0.48, 0.48, 0.48, 0.48] 

 imix-1t1c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.27, 0.27, 0.27, 0.27, 0.27, 0.27, 0.27, 0.27, 0.27, 0.27] 

 imix-2t2c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.45, 0.45, 0.44, 0.45, 0.45, 0.45, 0.45, 0.45, 0.45, 0.45] 

 imix-4t4c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.74, 0.74, 0.74, 0.74, 0.74, 0.74, 0.74, 0.74, 0.74, 0.74] 

40ge2p1xl710-ethip4ipsec1000tnlsw-ip4base-int-aes128gcm-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to

umber of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG ode interfaces. Incrementing of IP.dst (IPv4 destination address) is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-mrr

 [0.92, 0.92, 0.92, 0.92, 0.92, 0.92, 0.92, 0.92, 0.92, 0.92] 

 1518b-2t2c-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-mrr

 [1.80, 1.80, 1.80, 1.79, 1.79, 1.79, 1.79, 1.79, 1.79, 1.79] 

 1518b-4t4c-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-mrr

 [3.52, 3.51, 3.52, 3.51, 3.50, 3.50, 3.50, 3.50, 3.50, 3.50] 

 imix-1t1c-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-mrr

 [1.65, 1.65, 1.65, 1.65, 1.65, 1.64, 1.65, 1.64, 1.64, 1.64] 

 imix-2t2c-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-mrr

 [3.34, 3.33, 3.34, 3.34, 3.33, 3.34, 3.32, 3.32, 3.33, 3.33] 

 imix-4t4c-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-mrr

 [6.80, 6.78, 6.77, 6.78, 6.78, 6.78, 6.79, 6.77, 6.77, 6.76] 

40ge2p1xl710-ethip4ipsec1000tnlsw-ip4base-int-aes256gcm-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to

umber of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG ode interfaces. Incrementing of IP.dst (IPv4 destination address) is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-mrr

 [0.86, 0.86, 0.86, 0.86, 0.86, 0.86, 0.86, 0.85, 0.85, 0.86] 

 1518b-2t2c-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-mrr

 [1.70, 1.70, 1.70, 1.69, 1.69, 1.69, 1.69, 1.69, 1.69, 1.69] 

 1518b-4t4c-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-mrr

 [3.32, 3.32, 3.32, 3.32, 3.33, 3.32, 3.32, 3.32, 3.31, 3.31] 

 imix-1t1c-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-mrr

 [1.59, 1.58, 1.59, 1.58, 1.58, 1.58, 1.58, 1.58, 1.58, 1.58] 

 imix-2t2c-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-mrr

 [3.14, 3.14, 3.14, 3.15, 3.14, 3.14, 3.13, 3.13, 3.13, 3.13] 

 imix-4t4c-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-mrr

 [6.50, 6.47, 6.46, 6.45, 6.46, 6.46, 6.45, 6.44, 6.45, 6.44] 

40ge2p1xl710-ethip4ipsec1000tnlsw-ip4base-policy-aes256gcm-mrr

IPv4 IPsec tunnel mode performance test suite.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to

umber of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG ode interfaces. Incrementing of IP.dst (IPv4 destination address) is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec1000tnlsw- 
ip4base-policy-aes256gcm-mrr

 [0.63, 0.63, 0.63, 0.63, 0.63, 0.62, 0.63, 0.63, 0.63, 0.63] 

 64b-2t2c-ethip4ipsec1000tnlsw- 
ip4base-policy-aes256gcm-mrr

 [1.27, 1.27, 1.27, 1.27, 1.28, 1.27, 1.27, 1.26, 1.27, 1.27] 

 64b-4t4c-ethip4ipsec1000tnlsw- 
ip4base-policy-aes256gcm-mrr

 [2.55, 2.56, 2.57, 2.56, 2.57, 2.56, 2.55, 2.54, 2.56, 2.55] 

40ge2p1xl710-ethip4ipsec100spe-cache-ip4base-policy-outbound-nocrypto-mrr

RFC4301: SPD lookup performance

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing, wo static IPv4 /24 route entries, one SPD on each outbound interface in each direction and 100 SPD entry(ies) in each SPD. Only outbound traffic is matched and only the last rule is the matching

ule. SPD flow-cache for IPv4 outbound traffic is enabled. DUT1 tested with Intel-XL710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. The DUT does SPD lookup with only he lowest priority rule matching the traffic. The action of the matching rule is BYPASS. No encryption or authentication is done.

  • [Ref] Applicable standard specifications: RFC4301 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec100spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [6.24, 6.24, 6.24, 6.25, 6.23, 6.23, 6.24, 6.24, 6.23, 6.23] 

 64b-2t2c-ethip4ipsec100spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [12.83, 12.84, 12.81, 12.82, 12.83, 12.86, 12.83, 12.84, 12.82, 12.83] 

 64b-4t4c-ethip4ipsec100spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [25.57, 25.57, 25.62, 25.64, 25.59, 25.62, 25.62, 25.59, 25.57, 25.56] 

40ge2p1xl710-ethip4ipsec100spe-ip4base-policy-outbound-nocrypto-mrr

RFC4301: SPD lookup performance

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing, wo static IPv4 /24 route entries, one SPD on each outbound interface in each direction and 100 SPD entry(ies) in each SPD. Only outbound traffic is matched and only the last rule is the matching

ule. DUT1 tested with Intel-XL710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. The DUT does SPD lookup with only he lowest priority rule matching the traffic. The action of the matching rule is BYPASS. No encryption or authentication is done.

  • [Ref] Applicable standard specifications: RFC4301 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec100spe-ip4base- 
policy-outbound-nocrypto-mrr

 [3.34, 3.35, 3.35, 3.34, 3.34, 3.34, 3.35, 3.34, 3.34, 3.34] 

 64b-2t2c-ethip4ipsec100spe-ip4base- 
policy-outbound-nocrypto-mrr

 [6.66, 6.66, 6.65, 6.66, 6.67, 6.66, 6.66, 6.66, 6.67, 6.67] 

 64b-4t4c-ethip4ipsec100spe-ip4base- 
policy-outbound-nocrypto-mrr

 [13.23, 13.20, 13.21, 13.23, 13.20, 13.17, 13.18, 13.21, 13.18, 13.19] 

40ge2p1xl710-ethip4ipsec1spe-cache-ip4base-policy-outbound-nocrypto-mrr

RFC4301: SPD lookup performance

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing, wo static IPv4 /24 route entries, one SPD on each outbound interface in each direction and 1 SPD entry(ies) in each SPD. Only outbound traffic is matched and only the last rule is the matching

ule. SPD flow-cache for IPv4 outbound traffic is enabled. DUT1 tested with Intel-XL710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. The DUT does SPD lookup with only he lowest priority rule matching the traffic. The action of the matching rule is BYPASS. No encryption or authentication is done.

  • [Ref] Applicable standard specifications: RFC4301 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec1spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [6.26, 6.26, 6.26, 6.26, 6.25, 6.26, 6.27, 6.27, 6.26, 6.28] 

 64b-2t2c-ethip4ipsec1spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [12.72, 12.71, 12.73, 12.74, 12.74, 12.77, 12.76, 12.75, 12.68, 12.76] 

 64b-4t4c-ethip4ipsec1spe-cache- 
ip4base-policy-outbound-nocrypto-mrr

 [25.42, 25.44, 25.38, 25.40, 25.43, 25.42, 25.40, 25.39, 25.43, 25.41] 

40ge2p1xl710-ethip4ipsec1spe-ip4base-policy-outbound-nocrypto-mrr

RFC4301: SPD lookup performance

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing, wo static IPv4 /24 route entries, one SPD on each outbound interface in each direction and 1 SPD entry(ies) in each SPD. Only outbound traffic is matched and only the last rule is the matching

ule. DUT1 tested with Intel-XL710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. The DUT does SPD lookup with only he lowest priority rule matching the traffic. The action of the matching rule is BYPASS. No encryption or authentication is done.

  • [Ref] Applicable standard specifications: RFC4301 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec1spe-ip4base- 
policy-outbound-nocrypto-mrr

 [7.39, 7.41, 7.39, 7.41, 7.39, 7.39, 7.42, 7.39, 7.39, 7.42] 

 64b-2t2c-ethip4ipsec1spe-ip4base- 
policy-outbound-nocrypto-mrr

 [14.69, 14.65, 14.64, 14.63, 14.67, 14.69, 14.66, 14.70, 14.66, 14.67] 

 64b-4t4c-ethip4ipsec1spe-ip4base- 
policy-outbound-nocrypto-mrr

 [28.79, 28.87, 28.85, 28.79, 28.85, 28.79, 28.79, 28.78, 28.75, 28.83] 

40ge2p1xl710-ethip4ipsec1tnlsw-ip4base-policy-aes256gcm-mrr

IPv4 IPsec tunnel mode performance test suite.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to

umber of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG ode interfaces. Incrementing of IP.dst (IPv4 destination address) is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec1tnlsw- 
ip4base-policy-aes256gcm-mrr

 [3.66, 3.66, 3.66, 3.66, 3.66, 3.65, 3.65, 3.67, 3.65, 3.66] 

 64b-2t2c-ethip4ipsec1tnlsw- 
ip4base-policy-aes256gcm-mrr

 [7.61, 7.63, 7.63, 7.62, 7.59, 7.61, 7.62, 7.61, 7.62, 7.63] 

 64b-4t4c-ethip4ipsec1tnlsw- 
ip4base-policy-aes256gcm-mrr

 [7.61, 7.64, 7.63, 7.62, 7.62, 7.64, 7.63, 7.63, 7.63, 7.63] 

40ge2p1xl710-ethip4ipsec40tnlsw-ip4base-policy-aes256gcm-mrr

IPv4 IPsec tunnel mode performance test suite.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to

umber of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG ode interfaces. Incrementing of IP.dst (IPv4 destination address) is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-1t1c-ethip4ipsec40tnlsw- 
ip4base-policy-aes256gcm-mrr

 [2.94, 2.95, 2.95, 2.95, 2.94, 2.94, 2.94, 2.94, 2.94, 2.95] 

 64b-2t2c-ethip4ipsec40tnlsw- 
ip4base-policy-aes256gcm-mrr

 [6.00, 6.02, 6.01, 5.99, 6.02, 6.00, 6.01, 6.02, 6.01, 6.02] 

 64b-4t4c-ethip4ipsec40tnlsw- 
ip4base-policy-aes256gcm-mrr

 [11.79, 11.81, 11.81, 11.81, 11.82, 11.82, 11.81, 11.81, 11.81, 11.79] 

40ge2p1xl710-ethip4ipsec4tnlsw-ip4base-int-aes128cbc-hmac512sha-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to

umber of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG ode interfaces. Incrementing of IP.dst (IPv4 destination address) is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.16, 0.16, 0.16, 0.15, 0.16, 0.16, 0.16, 0.15, 0.16, 0.15] 

 1518b-2t2c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.20, 0.20, 0.20, 0.21, 0.20, 0.20, 0.20, 0.21, 0.20, 0.21] 

 1518b-4t4c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31, 0.31] 

 imix-1t1c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.29, 0.29, 0.29, 0.29, 0.29, 0.29, 0.29, 0.29, 0.29, 0.29] 

 imix-2t2c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.35, 0.35, 0.35, 0.35, 0.35, 0.35, 0.35, 0.35, 0.35, 0.35] 

 imix-4t4c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-mrr

 [0.46, 0.46, 0.46, 0.46, 0.46, 0.46, 0.46, 0.46, 0.46, 0.46] 

40ge2p1xl710-ethip4ipsec4tnlsw-ip4base-int-aes128gcm-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to

umber of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG ode interfaces. Incrementing of IP.dst (IPv4 destination address) is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-mrr

 [1.03, 1.03, 1.03, 1.03, 1.03, 1.03, 1.02, 1.02, 1.03, 1.03] 

 1518b-2t2c-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-mrr

 [1.55, 1.55, 1.55, 1.55, 1.55, 1.55, 1.55, 1.55, 1.55, 1.55] 

 1518b-4t4c-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-mrr

 [2.43, 2.43, 2.43, 2.43, 2.43, 2.43, 2.43, 2.43, 2.43, 2.43] 

 imix-1t1c-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-mrr

 [2.15, 2.14, 2.14, 2.15, 2.14, 2.14, 2.15, 2.14, 2.14, 2.14] 

 imix-2t2c-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-mrr

 [3.36, 3.35, 3.36, 3.35, 3.35, 3.34, 3.34, 3.34, 3.34, 3.34] 

 imix-4t4c-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-mrr

 [5.66, 5.66, 5.66, 5.65, 5.66, 5.66, 5.66, 5.67, 5.65, 5.66] 

40ge2p1xl710-ethip4ipsec4tnlsw-ip4base-int-aes256gcm-mrr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular opology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to

umber of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG ode interfaces. Incrementing of IP.dst (IPv4 destination address) is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 1518b-1t1c-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-mrr

 [0.95, 0.95, 0.95, 0.95, 0.95, 0.95, 0.94, 0.94, 0.95, 0.94] 

 1518b-2t2c-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-mrr

 [1.44, 1.44, 1.44, 1.44, 1.44, 1.43, 1.44, 1.43, 1.43, 1.43] 

 1518b-4t4c-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-mrr

 [2.39, 2.39, 2.39, 2.39, 2.39, 2.38, 2.39, 2.39, 2.39, 2.39] 

 imix-1t1c-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-mrr

 [2.05, 2.05, 2.05, 2.04, 2.05, 2.05, 2.06, 2.05, 2.05, 2.05] 

 imix-2t2c-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-mrr

 [3.21, 3.21, 3.21, 3.21, 3.21, 3.20, 3.20, 3.20, 3.20, 3.21] 

 imix-4t4c-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-mrr

 [5.44, 5.43, 5.42, 5.43, 5.43, 5.42, 5.42, 5.44, 5.42, 5.42]