7.11.2.2. chain_dot1qip4vxlan¶
7.11.2.2.1. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm1t-testpmd-reconf suite¶
RFC2544: Packet loss L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and throughput NDR (Non DropRate) with zero packet loss tolerance, then measured loss at this loadwhile additional chain is configured.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | RECONF
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 10R1C | 1_ADDED_CHAIN | 10VM1T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm1t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${2}
| ${nf_dtc}= | ${0.5}
| ${nf_chains}= | ${10}
| ${nf_added_chains}= | ${1}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.1.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure packet loss during reconfig at NDR load.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
${nf_total_chains}= Evaluate ${nf_chains} + ${nf_added_chains}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_total_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
${unidirectional_throughput} = Find Throughput Using MLRsearch
Start Traffic on Background ${unidirectional_throughput}
And Initialize layer dot1q count=${nf_total_chains} vlan_per_chain=${False} start=${nf_chains+1}
And Initialize layer ip4vxlan count=${nf_total_chains} start=${nf_chains+1}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_total_chains} nf_nodes=${nf_nodes} start=${nf_chains+1}
${result}= Stop Running Traffic
Display Reconfig Test Message ${result}
7.11.2.2.1.2. 118B-1c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${1}
7.11.2.2.1.3. 118B-2c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${2}
7.11.2.2.1.4. 118B-4c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${4}
7.11.2.2.1.5. 1518B-1c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.1.6. 1518B-2c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.1.7. 1518B-4c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.1.8. 9000B-1c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.1.9. 9000B-2c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.1.10. 9000B-4c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.1.11. IMIX-1c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.1.12. IMIX-2c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.1.13. IMIX-4c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.2. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm2t-testpmd-reconf suite¶
RFC2544: Packet loss L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and throughput NDR (Non DropRate) with zero packet loss tolerance, then measured loss at this loadwhile additional chain is configured.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | RECONF
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 10R1C | 1_ADDED_CHAIN | 10VM2T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm2t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${1}
| ${nf_dtc}= | ${1}
| ${nf_chains}= | ${10}
| ${nf_added_chains}= | ${1}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.2.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure packet loss during reconfig at NDR load.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
${nf_total_chains}= Evaluate ${nf_chains} + ${nf_added_chains}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_total_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
${unidirectional_throughput} = Find Throughput Using MLRsearch
Start Traffic on Background ${unidirectional_throughput}
And Initialize layer dot1q count=${nf_total_chains} vlan_per_chain=${False} start=${nf_chains+1}
And Initialize layer ip4vxlan count=${nf_total_chains} start=${nf_chains+1}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_total_chains} nf_nodes=${nf_nodes} start=${nf_chains+1}
${result}= Stop Running Traffic
Display Reconfig Test Message ${result}
7.11.2.2.2.2. 118B-1c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${1}
7.11.2.2.2.3. 118B-2c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${2}
7.11.2.2.2.4. 118B-4c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${4}
7.11.2.2.2.5. 1518B-1c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.2.6. 1518B-2c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.2.7. 1518B-4c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.2.8. 9000B-1c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.2.9. 9000B-2c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.2.10. 9000B-4c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.2.11. IMIX-1c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.2.12. IMIX-2c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.2.13. IMIX-4c-dot1qip4vxlan-l2bd-10ch-1ach-20vh-10vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.3. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-10ch-20vh-10vm1t-testpmd-ndrpdr suite¶
RFC2544: Packet throughput L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 10R1C | 10VM1T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-10ch-20vh-10vm1t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${2}
| ${nf_dtc}= | ${0.5}
| ${nf_chains}= | ${10}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.3.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
Then Find NDR and PDR intervals using optimized search
7.11.2.2.3.2. 118B-1c-dot1qip4vxlan-l2bd-10ch-20vh-10vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${1}
7.11.2.2.3.3. 118B-2c-dot1qip4vxlan-l2bd-10ch-20vh-10vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${2}
7.11.2.2.3.4. 118B-4c-dot1qip4vxlan-l2bd-10ch-20vh-10vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${4}
7.11.2.2.3.5. 1518B-1c-dot1qip4vxlan-l2bd-10ch-20vh-10vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.3.6. 1518B-2c-dot1qip4vxlan-l2bd-10ch-20vh-10vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.3.7. 1518B-4c-dot1qip4vxlan-l2bd-10ch-20vh-10vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.3.8. 9000B-1c-dot1qip4vxlan-l2bd-10ch-20vh-10vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.3.9. 9000B-2c-dot1qip4vxlan-l2bd-10ch-20vh-10vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.3.10. 9000B-4c-dot1qip4vxlan-l2bd-10ch-20vh-10vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.3.11. IMIX-1c-dot1qip4vxlan-l2bd-10ch-20vh-10vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.3.12. IMIX-2c-dot1qip4vxlan-l2bd-10ch-20vh-10vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.3.13. IMIX-4c-dot1qip4vxlan-l2bd-10ch-20vh-10vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.4. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-10ch-20vh-10vm2t-testpmd-ndrpdr suite¶
RFC2544: Packet throughput L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 10R1C | 10VM2T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-10ch-20vh-10vm2t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${1}
| ${nf_dtc}= | ${1}
| ${nf_chains}= | ${10}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.4.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
Then Find NDR and PDR intervals using optimized search
7.11.2.2.4.2. 118B-1c-dot1qip4vxlan-l2bd-10ch-20vh-10vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${1}
7.11.2.2.4.3. 118B-2c-dot1qip4vxlan-l2bd-10ch-20vh-10vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${2}
7.11.2.2.4.4. 118B-4c-dot1qip4vxlan-l2bd-10ch-20vh-10vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${4}
7.11.2.2.4.5. 1518B-1c-dot1qip4vxlan-l2bd-10ch-20vh-10vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.4.6. 1518B-2c-dot1qip4vxlan-l2bd-10ch-20vh-10vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.4.7. 1518B-4c-dot1qip4vxlan-l2bd-10ch-20vh-10vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.4.8. 9000B-1c-dot1qip4vxlan-l2bd-10ch-20vh-10vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.4.9. 9000B-2c-dot1qip4vxlan-l2bd-10ch-20vh-10vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.4.10. 9000B-4c-dot1qip4vxlan-l2bd-10ch-20vh-10vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.4.11. IMIX-1c-dot1qip4vxlan-l2bd-10ch-20vh-10vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.4.12. IMIX-2c-dot1qip4vxlan-l2bd-10ch-20vh-10vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.4.13. IMIX-4c-dot1qip4vxlan-l2bd-10ch-20vh-10vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.5. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm1t-testpmd-reconf suite¶
RFC2544: Packet loss L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and throughput NDR (Non DropRate) with zero packet loss tolerance, then measured loss at this loadwhile additional chain is configured.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | RECONF
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 1R1C | 1_ADDED_CHAIN | 1VM1T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm1t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${2}
| ${nf_dtc}= | ${0.5}
| ${nf_chains}= | ${1}
| ${nf_added_chains}= | ${1}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.5.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure packet loss during reconfig at NDR load.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
${nf_total_chains}= Evaluate ${nf_chains} + ${nf_added_chains}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_total_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
${unidirectional_throughput} = Find Throughput Using MLRsearch
Start Traffic on Background ${unidirectional_throughput}
And Initialize layer dot1q count=${nf_total_chains} vlan_per_chain=${False} start=${nf_chains+1}
And Initialize layer ip4vxlan count=${nf_total_chains} start=${nf_chains+1}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_total_chains} nf_nodes=${nf_nodes} start=${nf_chains+1}
${result}= Stop Running Traffic
Display Reconfig Test Message ${result}
7.11.2.2.5.2. 118B-1c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${1}
7.11.2.2.5.3. 118B-2c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${2}
7.11.2.2.5.4. 118B-4c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${4}
7.11.2.2.5.5. 1518B-1c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.5.6. 1518B-2c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.5.7. 1518B-4c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.5.8. 9000B-1c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.5.9. 9000B-2c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.5.10. 9000B-4c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.5.11. IMIX-1c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.5.12. IMIX-2c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.5.13. IMIX-4c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.6. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm2t-testpmd-reconf suite¶
RFC2544: Packet loss L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and throughput NDR (Non DropRate) with zero packet loss tolerance, then measured loss at this loadwhile additional chain is configured.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | RECONF
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 1R1C | 1_ADDED_CHAIN | 1VM2T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm2t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${1}
| ${nf_dtc}= | ${1}
| ${nf_chains}= | ${1}
| ${nf_added_chains}= | ${1}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.6.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure packet loss during reconfig at NDR load.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
${nf_total_chains}= Evaluate ${nf_chains} + ${nf_added_chains}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_total_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
${unidirectional_throughput} = Find Throughput Using MLRsearch
Start Traffic on Background ${unidirectional_throughput}
And Initialize layer dot1q count=${nf_total_chains} vlan_per_chain=${False} start=${nf_chains+1}
And Initialize layer ip4vxlan count=${nf_total_chains} start=${nf_chains+1}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_total_chains} nf_nodes=${nf_nodes} start=${nf_chains+1}
${result}= Stop Running Traffic
Display Reconfig Test Message ${result}
7.11.2.2.6.2. 118B-1c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${1}
7.11.2.2.6.3. 118B-2c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${2}
7.11.2.2.6.4. 118B-4c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${4}
7.11.2.2.6.5. 1518B-1c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.6.6. 1518B-2c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.6.7. 1518B-4c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.6.8. 9000B-1c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.6.9. 9000B-2c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.6.10. 9000B-4c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.6.11. IMIX-1c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.6.12. IMIX-2c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.6.13. IMIX-4c-dot1qip4vxlan-l2bd-1ch-1ach-2vh-1vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.7. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-1ch-2vh-1vm1t-testpmd-ndrpdr suite¶
RFC2544: Packet throughput L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 1R1C | 1VM1T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-1ch-2vh-1vm1t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${2}
| ${nf_dtc}= | ${0.5}
| ${nf_chains}= | ${1}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.7.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${false} vnf=testpmd_io
Then Find NDR and PDR intervals using optimized search
7.11.2.2.7.2. 118B-1c-dot1qip4vxlan-l2bd-1ch-2vh-1vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${1}
7.11.2.2.7.3. 118B-2c-dot1qip4vxlan-l2bd-1ch-2vh-1vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${2}
7.11.2.2.7.4. 118B-4c-dot1qip4vxlan-l2bd-1ch-2vh-1vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${4}
7.11.2.2.7.5. 1518B-1c-dot1qip4vxlan-l2bd-1ch-2vh-1vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.7.6. 1518B-2c-dot1qip4vxlan-l2bd-1ch-2vh-1vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.7.7. 1518B-4c-dot1qip4vxlan-l2bd-1ch-2vh-1vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.7.8. 9000B-1c-dot1qip4vxlan-l2bd-1ch-2vh-1vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.7.9. 9000B-2c-dot1qip4vxlan-l2bd-1ch-2vh-1vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.7.10. 9000B-4c-dot1qip4vxlan-l2bd-1ch-2vh-1vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.7.11. IMIX-1c-dot1qip4vxlan-l2bd-1ch-2vh-1vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.7.12. IMIX-2c-dot1qip4vxlan-l2bd-1ch-2vh-1vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.7.13. IMIX-4c-dot1qip4vxlan-l2bd-1ch-2vh-1vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.8. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-1ch-2vh-1vm2t-testpmd-ndrpdr suite¶
RFC2544: Packet throughput L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 1R1C | 1VM2T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-1ch-2vh-1vm2t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${1}
| ${nf_dtc}= | ${1}
| ${nf_chains}= | ${1}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.8.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${false} vnf=testpmd_io
Then Find NDR and PDR intervals using optimized search
7.11.2.2.8.2. 118B-1c-dot1qip4vxlan-l2bd-1ch-2vh-1vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${1}
7.11.2.2.8.3. 118B-2c-dot1qip4vxlan-l2bd-1ch-2vh-1vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${2}
7.11.2.2.8.4. 118B-4c-dot1qip4vxlan-l2bd-1ch-2vh-1vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${4}
7.11.2.2.8.5. 1518B-1c-dot1qip4vxlan-l2bd-1ch-2vh-1vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.8.6. 1518B-2c-dot1qip4vxlan-l2bd-1ch-2vh-1vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.8.7. 1518B-4c-dot1qip4vxlan-l2bd-1ch-2vh-1vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.8.8. 9000B-1c-dot1qip4vxlan-l2bd-1ch-2vh-1vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.8.9. 9000B-2c-dot1qip4vxlan-l2bd-1ch-2vh-1vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.8.10. 9000B-4c-dot1qip4vxlan-l2bd-1ch-2vh-1vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.8.11. IMIX-1c-dot1qip4vxlan-l2bd-1ch-2vh-1vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.8.12. IMIX-2c-dot1qip4vxlan-l2bd-1ch-2vh-1vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.8.13. IMIX-4c-dot1qip4vxlan-l2bd-1ch-2vh-1vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.9. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm1t-testpmd-reconf suite¶
RFC2544: Packet loss L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and throughput NDR (Non DropRate) with zero packet loss tolerance, then measured loss at this loadwhile additional chain is configured.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | RECONF
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 2R1C | 1_ADDED_CHAIN | 2VM1T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm1t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${2}
| ${nf_dtc}= | ${0.5}
| ${nf_chains}= | ${2}
| ${nf_added_chains}= | ${1}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.9.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure packet loss during reconfig at NDR load.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
${nf_total_chains}= Evaluate ${nf_chains} + ${nf_added_chains}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_total_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
${unidirectional_throughput} = Find Throughput Using MLRsearch
Start Traffic on Background ${unidirectional_throughput}
And Initialize layer dot1q count=${nf_total_chains} vlan_per_chain=${False} start=${nf_chains+1}
And Initialize layer ip4vxlan count=${nf_total_chains} start=${nf_chains+1}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_total_chains} nf_nodes=${nf_nodes} start=${nf_chains+1}
${result}= Stop Running Traffic
Display Reconfig Test Message ${result}
7.11.2.2.9.2. 118B-1c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${1}
7.11.2.2.9.3. 118B-2c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${2}
7.11.2.2.9.4. 118B-4c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${4}
7.11.2.2.9.5. 1518B-1c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.9.6. 1518B-2c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.9.7. 1518B-4c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.9.8. 9000B-1c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.9.9. 9000B-2c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.9.10. 9000B-4c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.9.11. IMIX-1c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.9.12. IMIX-2c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.9.13. IMIX-4c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.10. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm2t-testpmd-reconf suite¶
RFC2544: Packet loss L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and throughput NDR (Non DropRate) with zero packet loss tolerance, then measured loss at this loadwhile additional chain is configured.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | RECONF
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 2R1C | 1_ADDED_CHAIN | 2VM2T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm2t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${1}
| ${nf_dtc}= | ${1}
| ${nf_chains}= | ${2}
| ${nf_added_chains}= | ${1}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.10.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure packet loss during reconfig at NDR load.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
${nf_total_chains}= Evaluate ${nf_chains} + ${nf_added_chains}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_total_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
${unidirectional_throughput} = Find Throughput Using MLRsearch
Start Traffic on Background ${unidirectional_throughput}
And Initialize layer dot1q count=${nf_total_chains} vlan_per_chain=${False} start=${nf_chains+1}
And Initialize layer ip4vxlan count=${nf_total_chains} start=${nf_chains+1}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_total_chains} nf_nodes=${nf_nodes} start=${nf_chains+1}
${result}= Stop Running Traffic
Display Reconfig Test Message ${result}
7.11.2.2.10.2. 118B-1c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${1}
7.11.2.2.10.3. 118B-2c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${2}
7.11.2.2.10.4. 118B-4c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${4}
7.11.2.2.10.5. 1518B-1c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.10.6. 1518B-2c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.10.7. 1518B-4c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.10.8. 9000B-1c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.10.9. 9000B-2c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.10.10. 9000B-4c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.10.11. IMIX-1c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.10.12. IMIX-2c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.10.13. IMIX-4c-dot1qip4vxlan-l2bd-2ch-1ach-4vh-2vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.11. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-2ch-4vh-2vm1t-testpmd-ndrpdr suite¶
RFC2544: Packet throughput L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 2R1C | 2VM1T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-2ch-4vh-2vm1t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${2}
| ${nf_dtc}= | ${0.5}
| ${nf_chains}= | ${2}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.11.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
Then Find NDR and PDR intervals using optimized search
7.11.2.2.11.2. 118B-1c-dot1qip4vxlan-l2bd-2ch-4vh-2vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${1}
7.11.2.2.11.3. 118B-2c-dot1qip4vxlan-l2bd-2ch-4vh-2vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${2}
7.11.2.2.11.4. 118B-4c-dot1qip4vxlan-l2bd-2ch-4vh-2vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${4}
7.11.2.2.11.5. 1518B-1c-dot1qip4vxlan-l2bd-2ch-4vh-2vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.11.6. 1518B-2c-dot1qip4vxlan-l2bd-2ch-4vh-2vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.11.7. 1518B-4c-dot1qip4vxlan-l2bd-2ch-4vh-2vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.11.8. 9000B-1c-dot1qip4vxlan-l2bd-2ch-4vh-2vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.11.9. 9000B-2c-dot1qip4vxlan-l2bd-2ch-4vh-2vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.11.10. 9000B-4c-dot1qip4vxlan-l2bd-2ch-4vh-2vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.11.11. IMIX-1c-dot1qip4vxlan-l2bd-2ch-4vh-2vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.11.12. IMIX-2c-dot1qip4vxlan-l2bd-2ch-4vh-2vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.11.13. IMIX-4c-dot1qip4vxlan-l2bd-2ch-4vh-2vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.12. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-2ch-4vh-2vm2t-testpmd-ndrpdr suite¶
RFC2544: Packet throughput L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 2R1C | 2VM2T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-2ch-4vh-2vm2t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${1}
| ${nf_dtc}= | ${1}
| ${nf_chains}= | ${2}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.12.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
Then Find NDR and PDR intervals using optimized search
7.11.2.2.12.2. 118B-1c-dot1qip4vxlan-l2bd-2ch-4vh-2vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${1}
7.11.2.2.12.3. 118B-2c-dot1qip4vxlan-l2bd-2ch-4vh-2vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${2}
7.11.2.2.12.4. 118B-4c-dot1qip4vxlan-l2bd-2ch-4vh-2vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${4}
7.11.2.2.12.5. 1518B-1c-dot1qip4vxlan-l2bd-2ch-4vh-2vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.12.6. 1518B-2c-dot1qip4vxlan-l2bd-2ch-4vh-2vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.12.7. 1518B-4c-dot1qip4vxlan-l2bd-2ch-4vh-2vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.12.8. 9000B-1c-dot1qip4vxlan-l2bd-2ch-4vh-2vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.12.9. 9000B-2c-dot1qip4vxlan-l2bd-2ch-4vh-2vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.12.10. 9000B-4c-dot1qip4vxlan-l2bd-2ch-4vh-2vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.12.11. IMIX-1c-dot1qip4vxlan-l2bd-2ch-4vh-2vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.12.12. IMIX-2c-dot1qip4vxlan-l2bd-2ch-4vh-2vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.12.13. IMIX-4c-dot1qip4vxlan-l2bd-2ch-4vh-2vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.13. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm1t-testpmd-reconf suite¶
RFC2544: Packet throughput L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and throughput NDR (Non DropRate) with zero packet loss tolerance, then measured loss at this loadwhile additional chain is configured.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | RECONF
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 4R1C | 1_ADDED_CHAIN | 4VM1T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm1t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${2}
| ${nf_dtc}= | ${0.5}
| ${nf_chains}= | ${4}
| ${nf_added_chains}= | ${1}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.13.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure packet loss during reconfig at NDR load.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
${nf_total_chains}= Evaluate ${nf_chains} + ${nf_added_chains}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_total_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
${unidirectional_throughput} = Find Throughput Using MLRsearch
Start Traffic on Background ${unidirectional_throughput}
And Initialize layer dot1q count=${nf_total_chains} vlan_per_chain=${False} start=${nf_chains+1}
And Initialize layer ip4vxlan count=${nf_total_chains} start=${nf_chains+1}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_total_chains} nf_nodes=${nf_nodes} start=${nf_chains+1}
${result}= Stop Running Traffic
Display Reconfig Test Message ${result}
7.11.2.2.13.2. 118B-1c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${1}
7.11.2.2.13.3. 118B-2c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${2}
7.11.2.2.13.4. 118B-4c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${4}
7.11.2.2.13.5. 1518B-1c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.13.6. 1518B-2c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.13.7. 1518B-4c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.13.8. 9000B-1c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.13.9. 9000B-2c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.13.10. 9000B-4c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.13.11. IMIX-1c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.13.12. IMIX-2c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.13.13. IMIX-4c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.14. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm2t-testpmd-reconf suite¶
RFC2544: Packet throughput L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and throughput NDR (Non DropRate) with zero packet loss tolerance, then measured loss at this loadwhile additional chain is configured.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | RECONF
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 4R1C | 1_ADDED_CHAIN | 4VM2T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm2t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${1}
| ${nf_dtc}= | ${1}
| ${nf_chains}= | ${4}
| ${nf_added_chains}= | ${1}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.14.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure packet loss during reconfig at NDR load.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
${nf_total_chains}= Evaluate ${nf_chains} + ${nf_added_chains}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_total_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
${unidirectional_throughput} = Find Throughput Using MLRsearch
Start Traffic on Background ${unidirectional_throughput}
And Initialize layer dot1q count=${nf_total_chains} vlan_per_chain=${False} start=${nf_chains+1}
And Initialize layer ip4vxlan count=${nf_total_chains} start=${nf_chains+1}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_total_chains} nf_nodes=${nf_nodes} start=${nf_chains+1}
${result}= Stop Running Traffic
Display Reconfig Test Message ${result}
7.11.2.2.14.2. 118B-1c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${1}
7.11.2.2.14.3. 118B-2c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${2}
7.11.2.2.14.4. 118B-4c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${4}
7.11.2.2.14.5. 1518B-1c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.14.6. 1518B-2c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.14.7. 1518B-4c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.14.8. 9000B-1c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.14.9. 9000B-2c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.14.10. 9000B-4c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.14.11. IMIX-1c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.14.12. IMIX-2c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.14.13. IMIX-4c-dot1qip4vxlan-l2bd-4ch-1ach-8vh-4vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.15. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-4ch-8vh-4vm1t-testpmd-ndrpdr suite¶
RFC2544: Packet throughput L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 4R1C | 4VM1T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-4ch-8vh-4vm1t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${2}
| ${nf_dtc}= | ${0.5}
| ${nf_chains}= | ${4}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.15.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
Then Find NDR and PDR intervals using optimized search
7.11.2.2.15.2. 118B-1c-dot1qip4vxlan-l2bd-4ch-8vh-4vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${1}
7.11.2.2.15.3. 118B-2c-dot1qip4vxlan-l2bd-4ch-8vh-4vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${2}
7.11.2.2.15.4. 118B-4c-dot1qip4vxlan-l2bd-4ch-8vh-4vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${4}
7.11.2.2.15.5. 1518B-1c-dot1qip4vxlan-l2bd-4ch-8vh-4vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.15.6. 1518B-2c-dot1qip4vxlan-l2bd-4ch-8vh-4vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.15.7. 1518B-4c-dot1qip4vxlan-l2bd-4ch-8vh-4vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.15.8. 9000B-1c-dot1qip4vxlan-l2bd-4ch-8vh-4vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.15.9. 9000B-2c-dot1qip4vxlan-l2bd-4ch-8vh-4vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.15.10. 9000B-4c-dot1qip4vxlan-l2bd-4ch-8vh-4vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.15.11. IMIX-1c-dot1qip4vxlan-l2bd-4ch-8vh-4vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.15.12. IMIX-2c-dot1qip4vxlan-l2bd-4ch-8vh-4vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.15.13. IMIX-4c-dot1qip4vxlan-l2bd-4ch-8vh-4vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.16. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-4ch-8vh-4vm2t-testpmd-ndrpdr suite¶
RFC2544: Packet throughput L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 4R1C | 4VM2T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-4ch-8vh-4vm2t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${1}
| ${nf_dtc}= | ${1}
| ${nf_chains}= | ${4}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.16.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
Then Find NDR and PDR intervals using optimized search
7.11.2.2.16.2. 118B-1c-dot1qip4vxlan-l2bd-4ch-8vh-4vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${1}
7.11.2.2.16.3. 118B-2c-dot1qip4vxlan-l2bd-4ch-8vh-4vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${2}
7.11.2.2.16.4. 118B-4c-dot1qip4vxlan-l2bd-4ch-8vh-4vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${4}
7.11.2.2.16.5. 1518B-1c-dot1qip4vxlan-l2bd-4ch-8vh-4vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.16.6. 1518B-2c-dot1qip4vxlan-l2bd-4ch-8vh-4vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.16.7. 1518B-4c-dot1qip4vxlan-l2bd-4ch-8vh-4vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.16.8. 9000B-1c-dot1qip4vxlan-l2bd-4ch-8vh-4vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.16.9. 9000B-2c-dot1qip4vxlan-l2bd-4ch-8vh-4vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.16.10. 9000B-4c-dot1qip4vxlan-l2bd-4ch-8vh-4vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.16.11. IMIX-1c-dot1qip4vxlan-l2bd-4ch-8vh-4vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.16.12. IMIX-2c-dot1qip4vxlan-l2bd-4ch-8vh-4vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.16.13. IMIX-4c-dot1qip4vxlan-l2bd-4ch-8vh-4vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.17. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-6ch-12vh-6vm1t-testpmd-ndrpdr suite¶
RFC2544: Packet throughput L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 6R1C | 6VM1T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-6ch-12vh-6vm1t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${2}
| ${nf_dtc}= | ${0.5}
| ${nf_chains}= | ${6}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.17.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
Then Find NDR and PDR intervals using optimized search
7.11.2.2.17.2. 118B-1c-dot1qip4vxlan-l2bd-6ch-12vh-6vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${1}
7.11.2.2.17.3. 118B-2c-dot1qip4vxlan-l2bd-6ch-12vh-6vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${2}
7.11.2.2.17.4. 118B-4c-dot1qip4vxlan-l2bd-6ch-12vh-6vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${4}
7.11.2.2.17.5. 1518B-1c-dot1qip4vxlan-l2bd-6ch-12vh-6vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.17.6. 1518B-2c-dot1qip4vxlan-l2bd-6ch-12vh-6vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.17.7. 1518B-4c-dot1qip4vxlan-l2bd-6ch-12vh-6vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.17.8. 9000B-1c-dot1qip4vxlan-l2bd-6ch-12vh-6vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.17.9. 9000B-2c-dot1qip4vxlan-l2bd-6ch-12vh-6vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.17.10. 9000B-4c-dot1qip4vxlan-l2bd-6ch-12vh-6vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.17.11. IMIX-1c-dot1qip4vxlan-l2bd-6ch-12vh-6vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.17.12. IMIX-2c-dot1qip4vxlan-l2bd-6ch-12vh-6vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.17.13. IMIX-4c-dot1qip4vxlan-l2bd-6ch-12vh-6vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.18. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-6ch-12vh-6vm2t-testpmd-ndrpdr suite¶
RFC2544: Packet throughput L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 6R1C | 6VM2T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-6ch-12vh-6vm2t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${1}
| ${nf_dtc}= | ${1}
| ${nf_chains}= | ${6}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.18.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
Then Find NDR and PDR intervals using optimized search
7.11.2.2.18.2. 118B-1c-dot1qip4vxlan-l2bd-6ch-12vh-6vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${1}
7.11.2.2.18.3. 118B-2c-dot1qip4vxlan-l2bd-6ch-12vh-6vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${2}
7.11.2.2.18.4. 118B-4c-dot1qip4vxlan-l2bd-6ch-12vh-6vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${4}
7.11.2.2.18.5. 1518B-1c-dot1qip4vxlan-l2bd-6ch-12vh-6vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.18.6. 1518B-2c-dot1qip4vxlan-l2bd-6ch-12vh-6vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.18.7. 1518B-4c-dot1qip4vxlan-l2bd-6ch-12vh-6vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.18.8. 9000B-1c-dot1qip4vxlan-l2bd-6ch-12vh-6vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.18.9. 9000B-2c-dot1qip4vxlan-l2bd-6ch-12vh-6vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.18.10. 9000B-4c-dot1qip4vxlan-l2bd-6ch-12vh-6vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.18.11. IMIX-1c-dot1qip4vxlan-l2bd-6ch-12vh-6vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.18.12. IMIX-2c-dot1qip4vxlan-l2bd-6ch-12vh-6vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.18.13. IMIX-4c-dot1qip4vxlan-l2bd-6ch-12vh-6vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.19. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm1t-testpmd-reconf suite¶
RFC2544: Packet loss L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and throughput NDR (Non DropRate) with zero packet loss tolerance, then measured loss at this loadwhile additional chain is configured.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | RECONF
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 6R1C | 1_ADDED_CHAIN | 6VM1T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm1t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${2}
| ${nf_dtc}= | ${0.5}
| ${nf_chains}= | ${6}
| ${nf_added_chains}= | ${1}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.19.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure packet loss during reconfig at NDR load.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
${nf_total_chains}= Evaluate ${nf_chains} + ${nf_added_chains}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_total_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
${unidirectional_throughput} = Find Throughput Using MLRsearch
Start Traffic on Background ${unidirectional_throughput}
And Initialize layer dot1q count=${nf_total_chains} vlan_per_chain=${False} start=${nf_chains+1}
And Initialize layer ip4vxlan count=${nf_total_chains} start=${nf_chains+1}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_total_chains} nf_nodes=${nf_nodes} start=${nf_chains+1}
${result}= Stop Running Traffic
Display Reconfig Test Message ${result}
7.11.2.2.19.2. 118B-1c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${1}
7.11.2.2.19.3. 118B-2c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${2}
7.11.2.2.19.4. 118B-4c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${4}
7.11.2.2.19.5. 1518B-1c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.19.6. 1518B-2c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.19.7. 1518B-4c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.19.8. 9000B-1c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.19.9. 9000B-2c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.19.10. 9000B-4c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.19.11. IMIX-1c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.19.12. IMIX-2c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.19.13. IMIX-4c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.20. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm2t-testpmd-reconf suite¶
RFC2544: Packet loss L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and throughput NDR (Non DropRate) with zero packet loss tolerance, then measured loss at this loadwhile additional chain is configured.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | RECONF
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 6R1C | 1_ADDED_CHAIN | 6VM2T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm2t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${1}
| ${nf_dtc}= | ${1}
| ${nf_chains}= | ${6}
| ${nf_added_chains}= | ${1}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.20.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure packet loss during reconfig at NDR load.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
${nf_total_chains}= Evaluate ${nf_chains} + ${nf_added_chains}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_total_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
${unidirectional_throughput} = Find Throughput Using MLRsearch
Start Traffic on Background ${unidirectional_throughput}
And Initialize layer dot1q count=${nf_total_chains} vlan_per_chain=${False} start=${nf_chains+1}
And Initialize layer ip4vxlan count=${nf_total_chains} start=${nf_chains+1}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_total_chains} nf_nodes=${nf_nodes} start=${nf_chains+1}
${result}= Stop Running Traffic
Display Reconfig Test Message ${result}
7.11.2.2.20.2. 118B-1c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${1}
7.11.2.2.20.3. 118B-2c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${2}
7.11.2.2.20.4. 118B-4c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${4}
7.11.2.2.20.5. 1518B-1c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.20.6. 1518B-2c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.20.7. 1518B-4c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.20.8. 9000B-1c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.20.9. 9000B-2c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.20.10. 9000B-4c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.20.11. IMIX-1c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.20.12. IMIX-2c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.20.13. IMIX-4c-dot1qip4vxlan-l2bd-6ch-1ach-12vh-6vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.21. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-8ch-16vh-8vm1t-testpmd-ndrpdr suite¶
RFC2544: Packet throughput L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 8R1C | 8VM1T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-8ch-16vh-8vm1t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${2}
| ${nf_dtc}= | ${0.5}
| ${nf_chains}= | ${8}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.21.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
Then Find NDR and PDR intervals using optimized search
7.11.2.2.21.2. 118B-1c-dot1qip4vxlan-l2bd-8ch-16vh-8vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${1}
7.11.2.2.21.3. 118B-2c-dot1qip4vxlan-l2bd-8ch-16vh-8vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${2}
7.11.2.2.21.4. 118B-4c-dot1qip4vxlan-l2bd-8ch-16vh-8vm1t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${4}
7.11.2.2.21.5. 1518B-1c-dot1qip4vxlan-l2bd-8ch-16vh-8vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.21.6. 1518B-2c-dot1qip4vxlan-l2bd-8ch-16vh-8vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.21.7. 1518B-4c-dot1qip4vxlan-l2bd-8ch-16vh-8vm1t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.21.8. 9000B-1c-dot1qip4vxlan-l2bd-8ch-16vh-8vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.21.9. 9000B-2c-dot1qip4vxlan-l2bd-8ch-16vh-8vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.21.10. 9000B-4c-dot1qip4vxlan-l2bd-8ch-16vh-8vm1t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.21.11. IMIX-1c-dot1qip4vxlan-l2bd-8ch-16vh-8vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.21.12. IMIX-2c-dot1qip4vxlan-l2bd-8ch-16vh-8vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.21.13. IMIX-4c-dot1qip4vxlan-l2bd-8ch-16vh-8vm1t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.22. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-8ch-16vh-8vm2t-testpmd-ndrpdr suite¶
RFC2544: Packet throughput L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 8R1C | 8VM2T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-8ch-16vh-8vm2t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${1}
| ${nf_dtc}= | ${1}
| ${nf_chains}= | ${8}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.22.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
Then Find NDR and PDR intervals using optimized search
7.11.2.2.22.2. 118B-1c-dot1qip4vxlan-l2bd-8ch-16vh-8vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${1}
7.11.2.2.22.3. 118B-2c-dot1qip4vxlan-l2bd-8ch-16vh-8vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${2}
7.11.2.2.22.4. 118B-4c-dot1qip4vxlan-l2bd-8ch-16vh-8vm2t-testpmd-ndrpdr¶
frame_size=${118} phy_cores=${4}
7.11.2.2.22.5. 1518B-1c-dot1qip4vxlan-l2bd-8ch-16vh-8vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.22.6. 1518B-2c-dot1qip4vxlan-l2bd-8ch-16vh-8vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.22.7. 1518B-4c-dot1qip4vxlan-l2bd-8ch-16vh-8vm2t-testpmd-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.22.8. 9000B-1c-dot1qip4vxlan-l2bd-8ch-16vh-8vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.22.9. 9000B-2c-dot1qip4vxlan-l2bd-8ch-16vh-8vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.22.10. 9000B-4c-dot1qip4vxlan-l2bd-8ch-16vh-8vm2t-testpmd-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.22.11. IMIX-1c-dot1qip4vxlan-l2bd-8ch-16vh-8vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.22.12. IMIX-2c-dot1qip4vxlan-l2bd-8ch-16vh-8vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.22.13. IMIX-4c-dot1qip4vxlan-l2bd-8ch-16vh-8vm2t-testpmd-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.23. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm1t-testpmd-reconf suite¶
RFC2544: Packet loss L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and throughput NDR (Non DropRate) with zero packet loss tolerance, then measured loss at this loadwhile additional chain is configured.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | RECONF
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 8R1C | 1_ADDED_CHAIN | 8VM1T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm1t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${2}
| ${nf_dtc}= | ${0.5}
| ${nf_chains}= | ${8}
| ${nf_added_chains}= | ${1}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.23.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure packet loss during reconfig at NDR load.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
${nf_total_chains}= Evaluate ${nf_chains} + ${nf_added_chains}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_total_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
${unidirectional_throughput} = Find Throughput Using MLRsearch
Start Traffic on Background ${unidirectional_throughput}
And Initialize layer dot1q count=${nf_total_chains} vlan_per_chain=${False} start=${nf_chains+1}
And Initialize layer ip4vxlan count=${nf_total_chains} start=${nf_chains+1}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_total_chains} nf_nodes=${nf_nodes} start=${nf_chains+1}
${result}= Stop Running Traffic
Display Reconfig Test Message ${result}
7.11.2.2.23.2. 118B-1c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${1}
7.11.2.2.23.3. 118B-2c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${2}
7.11.2.2.23.4. 118B-4c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm1t-testpmd-reconf¶
frame_size=${118} phy_cores=${4}
7.11.2.2.23.5. 1518B-1c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.23.6. 1518B-2c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.23.7. 1518B-4c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm1t-testpmd-reconf¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.23.8. 9000B-1c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.23.9. 9000B-2c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.23.10. 9000B-4c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm1t-testpmd-reconf¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.23.11. IMIX-1c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.23.12. IMIX-2c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.23.13. IMIX-4c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm1t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.11.2.2.24. 2n-10ge2p1x710-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm2t-testpmd-reconf suite¶
RFC2544: Packet loss L2BD test cases with Dot1Q and VXLANoIPv4 with ${nf_chains} instances, ${nf_nodes} VMs per instance. [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 for L2switching of IPv4. Dot1q-IPv4-UDP-VXLAN-Eth-IPv4 is applied on linkbetween DUT1 and TG. [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain and MAC learning enabled. Qemu VNFs are connectedto VPP via vhost-user interfaces. Guest is running testpmd l2xcinterconnecting vhost-user interfaces, rxd/txd=1024. DUT1 istested with ${nic_name}. [Ver] TG verification: TG finds and throughput NDR (Non DropRate) with zero packet loss tolerance, then measured loss at this loadwhile additional chain is configured.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L3 flow-groups (flow-group per direction, 256 flows perflow-group) with all packets containing Ethernet header with .1Q, IPv4header, UPD header, VXLAN header and static payload. MAC addresses arematching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544, RFC7348.
# Copyright (c) 2021 Cisco and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | RECONF
| ... | NIC_Intel-X710 | L2BDMACLRN | ENCAP | VXLAN | L2OVRLAY | IP4UNRLAY
| ... | VHOST | VM | VHOST_1024 | VXLAN | DOT1Q | NF_DENSITY | NF_TESTPMD
| ... | CHAIN | 8R1C | 1_ADDED_CHAIN | 8VM2T | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm2t-testpmd
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance | vhost
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${54}
| ${nf_dtcr}= | ${1}
| ${nf_dtc}= | ${1}
| ${nf_chains}= | ${8}
| ${nf_added_chains}= | ${1}
| ${nf_nodes}= | ${1}
# Traffic profile:
| ${traffic_profile}=
| ... | trex-stl-dot1qip4vxlan-ip4src${nf_chains}udpsrcrnd7.11.2.2.24.1. Local Template¶
[Cfg] DUT runs Dot1Q-IP4-Vxlan L2BD switching config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure packet loss during reconfig at NDR load.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of worker threads to be used. Type: integer - rxq - Number of Rx queues to be used. Type: integer
Set Test Variable \${frame_size}
${nf_total_chains}= Evaluate ${nf_chains} + ${nf_added_chains}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface count=${nf_total_chains}
And Initialize layer dot1q count=${nf_chains} vlan_per_chain=${False}
And Initialize layer ip4vxlan count=${nf_chains}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_chains} nf_nodes=${nf_nodes}
And Configure chains of NFs connected via vhost-user nf_chains=${nf_chains} nf_nodes=${nf_nodes} jumbo=${jumbo} use_tuned_cfs=${False} auto_scale=${False} vnf=testpmd_io
${unidirectional_throughput} = Find Throughput Using MLRsearch
Start Traffic on Background ${unidirectional_throughput}
And Initialize layer dot1q count=${nf_total_chains} vlan_per_chain=${False} start=${nf_chains+1}
And Initialize layer ip4vxlan count=${nf_total_chains} start=${nf_chains+1}
And Initialize L2 bridge domains for multiple chains with Vhost-User nf_chains=${nf_total_chains} nf_nodes=${nf_nodes} start=${nf_chains+1}
${result}= Stop Running Traffic
Display Reconfig Test Message ${result}
7.11.2.2.24.2. 118B-1c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${1}
7.11.2.2.24.3. 118B-2c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${2}
7.11.2.2.24.4. 118B-4c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm2t-testpmd-reconf¶
frame_size=${118} phy_cores=${4}
7.11.2.2.24.5. 1518B-1c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${1}
7.11.2.2.24.6. 1518B-2c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${2}
7.11.2.2.24.7. 1518B-4c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm2t-testpmd-reconf¶
frame_size=${1518} phy_cores=${4}
7.11.2.2.24.8. 9000B-1c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${1}
7.11.2.2.24.9. 9000B-2c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${2}
7.11.2.2.24.10. 9000B-4c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm2t-testpmd-reconf¶
frame_size=${9000} phy_cores=${4}
7.11.2.2.24.11. IMIX-1c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.11.2.2.24.12. IMIX-2c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.11.2.2.24.13. IMIX-4c-dot1qip4vxlan-l2bd-8ch-1ach-16vh-8vm2t-testpmd-reconf¶
frame_size=IMIX_v4_1 phy_cores=${4}