7.10. lb¶
7.10.1. 2n1l-10ge2p1x710-ethip4-loadbalancer-l3dsr-ndrpdr suite¶
RFC2544: Pkt throughput loadbalancer l3dsr test cases [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Eth-IPv4-UDP for LoadBalancer l3dsr. [Cfg] DUT configuration: DUT1 is configured with LoadBalancerl3dsr and one static IPv4 /24 route entries. DUT1 tested with${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUT. TG traffic profilecontains two L4 flow-groups (l3dsr use flow-group is only from TGto DUT, 6 flows for flow-group) with all packets containing Ethernetheader, IPv4 header with IP protocol=17 and static payload. MACaddresses are matching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544.
# Copyright (c) 2021 Intel and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | ETH | IP4 | LOADBALANCER_L3DSR | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | ethip4-loadbalancer-l3dsr
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so | perfmon_plugin.so | lb_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${0}
# Traffic profile:
| ${traffic_profile}= | trex-stl-2n-ethip4udp-lb
| ${traffic_directions}= | ${1}
7.10.1.1. Local Template¶
[Cfg] DUT runs LoadBalancer l3dsr config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of physical cores. Type: integer - rxq - Number of RX queues, default value: ${None}. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface
And Initialize loadbalancer l3dsr
Then Find NDR and PDR intervals using optimized search
7.10.1.2. 64B-1c-ethip4-loadbalancer-l3dsr-ndrpdr¶
frame_size=${64} phy_cores=${1}
7.10.1.3. 64B-2c-ethip4-loadbalancer-l3dsr-ndrpdr¶
frame_size=${64} phy_cores=${2}
7.10.1.4. 64B-4c-ethip4-loadbalancer-l3dsr-ndrpdr¶
frame_size=${64} phy_cores=${4}
7.10.1.5. 1518B-1c-ethip4-loadbalancer-l3dsr-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.10.1.6. 1518B-2c-ethip4-loadbalancer-l3dsr-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.10.1.7. 1518B-4c-ethip4-loadbalancer-l3dsr-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.10.1.8. 9000B-1c-ethip4-loadbalancer-l3dsr-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.10.1.9. 9000B-2c-ethip4-loadbalancer-l3dsr-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.10.1.10. 9000B-4c-ethip4-loadbalancer-l3dsr-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.10.1.11. IMIX-1c-ethip4-loadbalancer-l3dsr-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.10.1.12. IMIX-2c-ethip4-loadbalancer-l3dsr-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.10.1.13. IMIX-4c-ethip4-loadbalancer-l3dsr-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.10.2. 2n1l-10ge2p1x710-ethip4-loadbalancer-maglev-ndrpdr suite¶
RFC2544: Pkt throughput loadbalancer maglev test cases [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Eth-IPv4-UDP for LoadBalancer maglev. [Cfg] DUT configuration: DUT1 is configured with LoadBalancermaglev and one static IPv4 /24 route entries. DUT1 tested with${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUT. TG traffic profilecontains two L4 flow-groups (maglev use flow-group is only from TGto DUT, 6 flows for flow-group) with all packets containing Ethernetheader, IPv4 header with IP protocol=17 and static payload. MACaddresses are matching MAC addresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544.
# Copyright (c) 2021 Intel and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | ETH | IP4 | LOADBALANCER_MAGLEV | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | ethip4-loadbalancer-maglev
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so | perfmon_plugin.so | lb_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${0}
# Traffic profile:
| ${traffic_profile}= | trex-stl-2n-ethip4udp-lb
| ${traffic_directions}= | ${1}
7.10.2.1. Local Template¶
[Cfg] DUT runs LoadBalancer maglev config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of physical cores. Type: integer - rxq - Number of RX queues, default value: ${None}. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface
And Initialize loadbalancer maglev
Then Find NDR and PDR intervals using optimized search
7.10.2.2. 64B-1c-ethip4-loadbalancer-maglev-ndrpdr¶
frame_size=${64} phy_cores=${1}
7.10.2.3. 64B-2c-ethip4-loadbalancer-maglev-ndrpdr¶
frame_size=${64} phy_cores=${2}
7.10.2.4. 64B-4c-ethip4-loadbalancer-maglev-ndrpdr¶
frame_size=${64} phy_cores=${4}
7.10.2.5. 1518B-1c-ethip4-loadbalancer-maglev-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.10.2.6. 1518B-2c-ethip4-loadbalancer-maglev-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.10.2.7. 1518B-4c-ethip4-loadbalancer-maglev-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.10.2.8. 9000B-1c-ethip4-loadbalancer-maglev-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.10.2.9. 9000B-2c-ethip4-loadbalancer-maglev-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.10.2.10. 9000B-4c-ethip4-loadbalancer-maglev-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.10.2.11. IMIX-1c-ethip4-loadbalancer-maglev-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.10.2.12. IMIX-2c-ethip4-loadbalancer-maglev-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.10.2.13. IMIX-4c-ethip4-loadbalancer-maglev-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}
7.10.3. 2n1l-10ge2p1x710-ethip4-loadbalancer-nat4-ndrpdr suite¶
RFC2544: Pkt throughput loadbalancer nat4 test cases [Top] Network Topologies: TG-DUT1-TG 2-node circular topologywith single links between nodes. [Enc] Packet Encapsulations: Eth-IPv4-UDP for LoadBalancer nat4. [Cfg] DUT configuration: DUT1 is configured with LoadBalancernat4 and two static IPv4 /24 route entries. DUT1 tested with${nic_name}. [Ver] TG verification: TG finds and reports throughput NDR (Non DropRate) with zero packet loss tolerance and throughput PDR (Partial DropRate) with non-zero packet loss tolerance (LT) expressed in percentageof packets transmitted. NDR and PDR are discovered for differentEthernet L2 frame sizes using MLRsearch library.Test packets are generated by TG on links to DUTs. TG traffic profilecontains two L4 flow-groups (flow-group per direction, 6 flows perflow-group) with all packets containing Ethernet header, IPv4 headerwith IP protocol=17 and static payload. MAC addresses are matching MACaddresses of the TG node interfaces. [Ref] Applicable standard specifications: RFC2544.
# Copyright (c) 2021 Intel and/or its affiliates.
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at:
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
*** Settings ***
| Resource | resources/libraries/robot/shared/default.robot
|
| Force Tags | 2_NODE_SINGLE_LINK_TOPO | PERFTEST | HW_ENV | NDRPDR
| ... | NIC_Intel-X710 | ETH | IP4 | LOADBALANCER_NAT4 | DRV_VFIO_PCI
| ... | RXQ_SIZE_0 | TXQ_SIZE_0
| ... | ethip4-loadbalancer-nat4
|
| Suite Setup | Setup suite topology interfaces | performance
| Suite Teardown | Tear down suite | performance
| Test Setup | Setup test | performance
| Test Teardown | Tear down test | performance
|
| Test Template | Local Template
|
| *** Variables ***
| @{plugins_to_enable}= | dpdk_plugin.so | perfmon_plugin.so | lb_plugin.so
| ${crypto_type}= | ${None}
| ${nic_name}= | Intel-X710
| ${nic_driver}= | vfio-pci
| ${nic_rxq_size}= | 0
| ${nic_txq_size}= | 0
| ${nic_pfs}= | 2
| ${nic_vfs}= | 0
| ${osi_layer}= | L3
| ${overhead}= | ${0}
# Traffic profile:
| ${traffic_profile}= | trex-stl-2n-ethip4udp-lb7.10.3.1. Local Template¶
[Cfg] DUT runs LoadBalancer nat4 config.Each DUT uses ${phy_cores} physical core(s) for worker threads. [Ver] Measure NDR and PDR values using MLRsearch algorithm.Arguments: - frame_size - Framesize in Bytes in integer or string (IMIX_v4_1). Type: integer, string - phy_cores - Number of physical cores. Type: integer - rxq - Number of RX queues, default value: ${None}. Type: integer
Set Test Variable \${frame_size}
Given Set Max Rate And Jumbo
And Add worker threads to all DUTs ${phy_cores} ${rxq}
And Pre-initialize layer driver ${nic_driver}
And Apply startup configuration on all VPP DUTs
When Initialize layer driver ${nic_driver}
And Initialize layer interface
And Initialize loadbalancer nat4
Then Find NDR and PDR intervals using optimized search
7.10.3.2. 64B-1c-ethip4-loadbalancer-nat4-ndrpdr¶
frame_size=${64} phy_cores=${1}
7.10.3.3. 64B-2c-ethip4-loadbalancer-nat4-ndrpdr¶
frame_size=${64} phy_cores=${2}
7.10.3.4. 64B-4c-ethip4-loadbalancer-nat4-ndrpdr¶
frame_size=${64} phy_cores=${4}
7.10.3.5. 1518B-1c-ethip4-loadbalancer-nat4-ndrpdr¶
frame_size=${1518} phy_cores=${1}
7.10.3.6. 1518B-2c-ethip4-loadbalancer-nat4-ndrpdr¶
frame_size=${1518} phy_cores=${2}
7.10.3.7. 1518B-4c-ethip4-loadbalancer-nat4-ndrpdr¶
frame_size=${1518} phy_cores=${4}
7.10.3.8. 9000B-1c-ethip4-loadbalancer-nat4-ndrpdr¶
frame_size=${9000} phy_cores=${1}
7.10.3.9. 9000B-2c-ethip4-loadbalancer-nat4-ndrpdr¶
frame_size=${9000} phy_cores=${2}
7.10.3.10. 9000B-4c-ethip4-loadbalancer-nat4-ndrpdr¶
frame_size=${9000} phy_cores=${4}
7.10.3.11. IMIX-1c-ethip4-loadbalancer-nat4-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${1}
7.10.3.12. IMIX-2c-ethip4-loadbalancer-nat4-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${2}
7.10.3.13. IMIX-4c-ethip4-loadbalancer-nat4-ndrpdr¶
frame_size=IMIX_v4_1 phy_cores=${4}