3n-tsh-x520

10ge2p1x520-ethip4-ip4base-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-ethip4-ip4base-ndrpdr 

 1.  5.49       3.69 
2. 5.55 3.73

3. 21 28 38 21 27 37
4. 57 79 98 53 85 97
5. 113 131 145 118 137 156

 64b-2t2c-ethip4-ip4base-ndrpdr 

 1.  6.72       4.51 
2. 6.82 4.58

3. 21 28 35 21 28 41
4. 44 64 75 41 62 72
5. 74 91 104 76 91 108

 64b-4t4c-ethip4-ip4base-ndrpdr 

 1.  6.74       4.53 
2. 7.13 4.79

3. 21 28 33 21 31 37
4. 33 55 64 34 46 55
5. 58 71 86 56 69 81

10ge2p1x520-ethip4-ip4scale200k-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c- 
ethip4-ip4scale200k-ndrpdr

 1.  0.02       0.01 
2. 4.53 3.04

3. 21 32 38 21 35 43
4. 70 86 95 79 119 131
5. 112 139 159 121 143 161

 64b-2t2c- 
ethip4-ip4scale200k-ndrpdr

 1.  5.39       3.62 
2. 5.53 3.71

3. 21 47 59 21 39 47
4. 42 72 90 42 66 84
5. 86 110 128 94 117 138

 64b-4t4c- 
ethip4-ip4scale200k-ndrpdr

 1.  5.53       3.72 
2. 5.56 3.74

3. 21 26 47 21 31 35
4. 32 63 71 36 59 68
5. 61 81 103 57 77 98

10ge2p1x520-ethip4-ip4scale20k-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c- 
ethip4-ip4scale20k-ndrpdr

 1.  5.10       3.43 
2. 5.13 3.45

3. 21 37 55 21 42 50
4. 55 90 103 56 89 105
5. 105 134 144 130 142 162

 64b-2t2c- 
ethip4-ip4scale20k-ndrpdr

 1.  5.78       3.89 
2. 5.84 3.93

3. 21 35 43 21 34 43
4. 39 56 66 40 62 71
5. 67 88 108 68 88 109

 64b-4t4c- 
ethip4-ip4scale20k-ndrpdr

 1.  5.99       4.03 
2. 6.24 4.19

3. 21 26 31 21 25 28
4. 32 49 57 33 42 51
5. 56 69 82 56 68 80

10ge2p1x520-ethip4-ip4scale2m-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c- 
ethip4-ip4scale2m-ndrpdr

 1.  4.49       3.02 
2. 4.49 3.02

3. 21 38 58 21 41 70
4. 22 45 55 25 80 89
5. 126 147 162 127 153 178

 64b-2t2c- 
ethip4-ip4scale2m-ndrpdr

 1.  5.36       3.60 
2. 5.52 3.71

3. 21 48 65 21 33 43
4. 36 61 75 40 63 80
5. 91 113 130 90 111 125

 64b-4t4c- 
ethip4-ip4scale2m-ndrpdr

 1.  5.56       3.74 
2. 5.62 3.77

3. 21 24 33 21 28 31
4. 36 51 61 34 50 60
5. 58 74 89 58 76 98

10ge2p1x520-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr

RFC2544: Packet throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-ethip4udp- 
ip4base-iacl50sf-10kflows-ndrpdr

 1.  3.59       2.41 
2. 3.63 2.44

3. 22 34 41 22 32 38
4. 40 70 91 44 63 78
5. 78 97 118 80 96 109

 64b-2t2c-ethip4udp- 
ip4base-iacl50sf-10kflows-ndrpdr

 1.  4.62       3.11 
2. 4.65 3.12

3. 24 38 52 23 35 41
4. 30 36 42 40 55 65
5. 59 75 90 61 78 91

 64b-4t4c-ethip4udp- 
ip4base-iacl50sf-10kflows-ndrpdr

 1.  5.36       3.60 
2. 5.81 3.90

3. 22 25 30 22 25 37
4. 33 57 66 34 45 57
5. 59 76 93 63 85 105

10ge2p1x520-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr

RFC2544: Packet throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-ethip4udp- 
ip4base-iacl50sl-10kflows-ndrpdr

 1.  3.46       2.33 
2. 3.48 2.34

3. 22 26 33 22 32 48
4. 40 67 81 45 80 100
5. 77 95 118 84 106 121

 64b-2t2c-ethip4udp- 
ip4base-iacl50sl-10kflows-ndrpdr

 1.  4.80       3.22 
2. 4.92 3.30

3. 22 27 38 22 26 40
4. 44 60 70 35 48 61
5. 60 75 91 63 81 94

 64b-4t4c-ethip4udp- 
ip4base-iacl50sl-10kflows-ndrpdr

 1.  5.67       3.81 
2. 6.23 4.19

3. 22 29 35 22 31 41
4. 36 49 60 35 48 57
5. 59 77 88 58 72 84

10ge2p1x520-ethip4udp-ip4base-oacl50sf-10kflows-ndrpdr

RFC2544: Packet throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-ethip4udp- 
ip4base-oacl50sf-10kflows-ndrpdr

 1.  3.56       2.40 
2. 3.60 2.42

3. 22 32 48 23 37 50
4. 46 83 100 47 82 98
5. 86 104 131 85 108 128

 64b-2t2c-ethip4udp- 
ip4base-oacl50sf-10kflows-ndrpdr

 1.  4.55       3.06 
2. 4.58 3.07

3. 23 34 44 23 41 52
4. 24 30 35 40 70 85
5. 63 80 93 66 87 100

 64b-4t4c-ethip4udp- 
ip4base-oacl50sf-10kflows-ndrpdr

 1.  5.28       3.55 
2. 5.61 3.77

3. 22 28 34 22 27 33
4. 37 50 58 36 46 57
5. 65 80 92 65 82 97

10ge2p1x520-ethip4udp-ip4base-oacl50sl-10kflows-ndrpdr

RFC2544: Packet throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to output paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-X520-DA2.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-1t1c-ethip4udp- 
ip4base-oacl50sl-10kflows-ndrpdr

 1.  3.43       2.30 
2. 3.44 2.31

3. 23 54 65 23 47 57
4. 48 79 92 50 77 94
5. 89 115 129 96 126 136

 64b-2t2c-ethip4udp- 
ip4base-oacl50sl-10kflows-ndrpdr

 1.  4.71       3.16 
2. 4.75 3.19

3. 22 24 26 22 27 43
4. 62 71 77 41 52 62
5. 61 78 95 65 83 96

 64b-4t4c-ethip4udp- 
ip4base-oacl50sl-10kflows-ndrpdr

 1.  5.69       3.82 
2. 6.07 4.08

3. 22 28 33 23 37 45
4. 37 54 63 35 46 58
5. 58 73 83 63 78 89