2n-clx-xxv710

2n1l-25ge2p1xxv710-avf-ethip4-ip4base-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf- 
 ethip4-ip4base-ndrpdr 

 1. 19.94      13.40 
 2. 20.04      13.47 
  
 3.   11   15   22        11   17   21  
 4.   20   23   28        20   25   29  
 5.   37   43   49        38   45   50  

 64b-4t2c-avf- 
 ethip4-ip4base-ndrpdr 

 1. 37.13      24.95 
 2. 37.31      25.07 
  
 3.   13   22   31        14   22   29  
 4.   18   23   26        19   23   26  
 5.   36   43   49        37   45   52  

 64b-8t4c-avf- 
 ethip4-ip4base-ndrpdr 

 1. 33.31      22.38 
 2. 33.81      22.72 
  
 3.   11   17   22        12   16   21  
 4.   16   21   27        17   22   28  
 5.   21   26   32        21   27   33

2n1l-25ge2p1xxv710-avf-ethip4-ip4scale200k-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf- 
 ethip4-ip4scale200k-ndrpdr 

 1. 18.70      12.57 
 2. 18.89      12.69 
  
 3.   11   15   20        12   16   19  
 4.   19   24   28        19   24   27  
 5.   43   53   61        43   54   62  

 64b-4t2c-avf- 
 ethip4-ip4scale200k-ndrpdr 

 1. 34.23      23.01 
 2. 34.58      23.24 
  
 3.   13   21   29        15   23   30  
 4.   19   23   26        20   24   27  
 5.   40   50   60        42   53   62  

 64b-8t4c-avf- 
 ethip4-ip4scale200k-ndrpdr 

 1. 34.23      23.00 
 2. 35.28      23.71 
  
 3.   13   18   22        12   17   22  
 4.   18   23   28        18   24   29  
 5.   22   29   35        22   31   37

2n1l-25ge2p1xxv710-avf-ethip4-ip4scale200k-rnd-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains 2 randomized L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf- 
 ethip4-ip4scale200k-rnd-ndrpdr 

 1. 16.78      11.28 
 2. 17.12      11.50 
  
 3.   11   14   18        11   16   23  
 4.   19   25   30        19   25   29  
 5.   43   53   61        45   55   64  

 64b-4t2c-avf- 
 ethip4-ip4scale200k-rnd-ndrpdr 

 1. 32.07      21.55 
 2. 33.05      22.21 
  
 3.   13   20   27        13   20   27  
 4.   21   25   29        21   26   30  
 5.   39   52   66        40   54   68  

 64b-8t4c-avf- 
 ethip4-ip4scale200k-rnd-ndrpdr 

 1. 36.39      24.45 
 2. 37.13      24.95 
  
 3.   12   18   23        13   18   24  
 4.   18   26   33        21   28   34  
 5.   28   50   64        37   57   69

2n1l-25ge2p1xxv710-avf-ethip4-ip4scale20k-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and 2x10k static IPv4 /32 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf- 
 ethip4-ip4scale20k-ndrpdr 

 1. 19.02      12.78 
 2. 19.41      13.04 
  
 3.   11   15   21        11   16   20  
 4.   19   25   28        19   25   28  
 5.   41   49   55        42   50   56  

 64b-4t2c-avf- 
 ethip4-ip4scale20k-ndrpdr 

 1. 29.26      19.66 
 2. 30.26      20.33 
  
 3.   12   16   23        12   16   20  
 4.   20   25   30        20   25   29  
 5.   37   50   57        43   54   61  

 64b-8t4c-avf- 
 ethip4-ip4scale20k-ndrpdr 

 1. 34.12      22.93 
 2. 34.99      23.51 
  
 3.   12   18   23        13   18   22  
 4.   18   23   28        18   23   28  
 5.   23   30   36        23   30   36

2n1l-25ge2p1xxv710-avf-ethip4-ip4scale20k-rnd-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and 2x10k static IPv4 /32 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains 2 randomized L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf- 
 ethip4-ip4scale20k-rnd-ndrpdr 

 1. 17.89      12.02 
 2. 18.07      12.14 
  
 3.   11   18   24        11   18   27  
 4.   18   24   27        21   26   29  
 5.   42   52   58        41   51   58  

 64b-4t2c-avf- 
 ethip4-ip4scale20k-rnd-ndrpdr 

 1. 33.59      22.57 
 2. 34.61      23.26 
  
 3.   12   19   25        15   24   29  
 4.   19   24   27        20   25   30  
 5.   38   53   65        40   55   67  

 64b-8t4c-avf- 
 ethip4-ip4scale20k-rnd-ndrpdr 

 1. 34.09      22.91 
 2. 34.96      23.49 
  
 3.   12   17   22        13   18   22  
 4.   18   23   28        18   23   28  
 5.   22   29   35        22   29   35

2n1l-25ge2p1xxv710-avf-ethip4-ip4scale2m-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and 2x1M static IPv4 /32 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf- 
 ethip4-ip4scale2m-ndrpdr 

 1. 16.74      11.25 
 2. 16.91      11.36 
  
 3.   11   14   17        11   14   19  
 4.   19   25   29        20   25   30  
 5.   58   71   86        59   73   88  

 64b-4t2c-avf- 
 ethip4-ip4scale2m-ndrpdr 

 1. 22.53      15.14 
 2. 23.65      15.89 
  
 3.   14   22   27        12   19   26  
 4.   20   27   34        22   27   35  
 5.   38   51   60        43   54   62  

 64b-8t4c-avf- 
 ethip4-ip4scale2m-ndrpdr 

 1. 33.70      22.65 
 2. 36.52      24.54 
  
 3.   13   19   23        13   18   22  
 4.   19   26   31        20   26   31  
 5.   27   39   48        27   39   48

2n1l-25ge2p1xxv710-avf-ethip4-ip4scale2m-rnd-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and 2x1M static IPv4 /32 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains 2 randomized L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf- 
 ethip4-ip4scale2m-rnd-ndrpdr 

 1. 13.19       8.86 
 2. 13.39       9.00 
  
 3.   11   17   22        11   15   20  
 4.   17   24   29        17   25   30  
 5.   43   53   62        43   53   62  

 64b-4t2c-avf- 
 ethip4-ip4scale2m-rnd-ndrpdr 

 1. 24.70      16.60 
 2. 25.58      17.19 
  
 3.   12   21   27        11   20   27  
 4.   19   24   29        20   25   29  
 5.   39   57   74        41   59   77  

 64b-8t4c-avf- 
 ethip4-ip4scale2m-rnd-ndrpdr 

 1. 35.81      24.06 
 2. 36.81      24.74 
  
 3.   13   18   23        13   18   23  
 4.   17   24   31        18   25   33  
 5.   27   47   61        27   49   62

2n1l-25ge2p1xxv710-avf-ethip4tcp-ip4base-h1024-p63-s64512-cps-ndrpdr

CPS on empty TCP transactions with IPv4 routing

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-TCP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional TCP flows) with all packets containing Ethernet header, IPv4 header with TCP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4tcp-ip4base- 
 h1024-p63-s64512-cps-ndrpdr 

 1.  2.24 
 2.  2.24 

 64b-4t2c-avf-ethip4tcp-ip4base- 
 h1024-p63-s64512-cps-ndrpdr 

 1.  2.06 
 2.  2.10 

 64b-8t4c-avf-ethip4tcp-ip4base- 
 h1024-p63-s64512-cps-ndrpdr 

 1.  2.04 
 2.  2.11

2n1l-25ge2p1xxv710-avf-ethip4tcp-ip4base-h16384-p63-s1032192-cps-ndrpdr

CPS on empty TCP transactions with IPv4 routing

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-TCP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional TCP flows) with all packets containing Ethernet header, IPv4 header with TCP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4tcp-ip4base- 
 h16384-p63-s1032192-cps-ndrpdr 

 1.  1.42 
 2.  1.51 

 64b-4t2c-avf-ethip4tcp-ip4base- 
 h16384-p63-s1032192-cps-ndrpdr 

 1.  1.43 
 2.  1.50 

 64b-8t4c-avf-ethip4tcp-ip4base- 
 h16384-p63-s1032192-cps-ndrpdr 

 1.  1.43 
 2.  1.49

2n1l-25ge2p1xxv710-avf-ethip4tcp-ip4base-h262144-p63-s16515072-cps-ndrpdr

CPS on empty TCP transactions with IPv4 routing

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-TCP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional TCP flows) with all packets containing Ethernet header, IPv4 header with TCP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4tcp-ip4base- 
 h262144-p63-s16515072-cps-ndrpdr 

 1.  1.33 
 2.  1.37 

 64b-4t2c-avf-ethip4tcp-ip4base- 
 h262144-p63-s16515072-cps-ndrpdr 

 1.  1.33 
 2.  1.36 

 64b-8t4c-avf-ethip4tcp-ip4base- 
 h262144-p63-s16515072-cps-ndrpdr 

 1.  1.33 
 2.  1.36

2n1l-25ge2p1xxv710-avf-ethip4tcp-ip4base-h65536-p63-s4128768-cps-ndrpdr

CPS on empty TCP transactions with IPv4 routing

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-TCP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional TCP flows) with all packets containing Ethernet header, IPv4 header with TCP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4tcp-ip4base- 
 h65536-p63-s4128768-cps-ndrpdr 

 1.  1.37 
 2.  1.42 

 64b-4t2c-avf-ethip4tcp-ip4base- 
 h65536-p63-s4128768-cps-ndrpdr 

 1.  1.36 
 2.  1.40 

 64b-8t4c-avf-ethip4tcp-ip4base- 
 h65536-p63-s4128768-cps-ndrpdr 

 1.  1.37 
 2.  1.40

2n1l-25ge2p1xxv710-avf-ethip4tcp-nat44ed-h1024-p63-s64512-cps-ndrpdr

CPS on empty TCP transactions with NAT44ED

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-TCP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and one static IPv4 /18 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional TCP flows) with all packets containing Ethernet header, IPv4 header with TCP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: Benchmarking Methodology for Network Security Device Performance (draft-ietf-bmwg-ngfw-performance-03).

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4tcp-nat44ed- 
 h1024-p63-s64512-cps-ndrpdr 

 1.  0.67 
 2.  0.67 

 64b-4t2c-avf-ethip4tcp-nat44ed- 
 h1024-p63-s64512-cps-ndrpdr 

 1.  0.98 
 2.  1.03 

 64b-8t4c-avf-ethip4tcp-nat44ed- 
 h1024-p63-s64512-cps-ndrpdr 

 1.  1.29 
 2.  1.37

2n1l-25ge2p1xxv710-avf-ethip4tcp-nat44ed-h16384-p63-s1032192-cps-ndrpdr

CPS on empty TCP transactions with NAT44ED

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-TCP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and one static IPv4 /18 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional TCP flows) with all packets containing Ethernet header, IPv4 header with TCP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: Benchmarking Methodology for Network Security Device Performance (draft-ietf-bmwg-ngfw-performance-03).

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4tcp-nat44ed- 
 h16384-p63-s1032192-cps-ndrpdr 

 1.  0.52 
 2.  0.52 

 64b-4t2c-avf-ethip4tcp-nat44ed- 
 h16384-p63-s1032192-cps-ndrpdr 

 1.  0.81 
 2.  0.87 

 64b-8t4c-avf-ethip4tcp-nat44ed- 
 h16384-p63-s1032192-cps-ndrpdr 

 1.  1.14 
 2.  1.21

2n1l-25ge2p1xxv710-avf-ethip4tcp-nat44ed-h262144-p63-s16515072-cps-ndrpdr

CPS on empty TCP transactions with NAT44ED

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-TCP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and one static IPv4 /18 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional TCP flows) with all packets containing Ethernet header, IPv4 header with TCP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: Benchmarking Methodology for Network Security Device Performance (draft-ietf-bmwg-ngfw-performance-03).

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4tcp-nat44ed- 
 h262144-p63-s16515072-cps-ndrpdr 

 1.  0.39 
 2.  0.39 

 64b-4t2c-avf-ethip4tcp-nat44ed- 
 h262144-p63-s16515072-cps-ndrpdr 

 1.  0.63 
 2.  0.66 

 64b-8t4c-avf-ethip4tcp-nat44ed- 
 h262144-p63-s16515072-cps-ndrpdr 

 1.  0.92 
 2.  0.97

2n1l-25ge2p1xxv710-avf-ethip4tcp-nat44ed-h65536-p63-s4128768-cps-ndrpdr

CPS on empty TCP transactions with NAT44ED

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-TCP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and one static IPv4 /18 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional TCP flows) with all packets containing Ethernet header, IPv4 header with TCP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: Benchmarking Methodology for Network Security Device Performance (draft-ietf-bmwg-ngfw-performance-03).

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4tcp-nat44ed- 
 h65536-p63-s4128768-cps-ndrpdr 

 1.  0.47 
 2.  0.47 

 64b-4t2c-avf-ethip4tcp-nat44ed- 
 h65536-p63-s4128768-cps-ndrpdr 

 1.  0.74 
 2.  0.79 

 64b-8t4c-avf-ethip4tcp-nat44ed- 
 h65536-p63-s4128768-cps-ndrpdr 

 1.  1.06 
 2.  1.12

2n1l-25ge2p1xxv710-avf-ethip4udp-ip4base-h1024-p63-s64512-cps-ndrpdr

CPS on empty UDP transactions with IPv4 routing

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /22 route entries. DUT1 tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional UDP flows) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp-ip4base- 
 h1024-p63-s64512-cps-ndrpdr 

 1.  5.48 
 2.  5.48 

 64b-4t2c-avf-ethip4udp-ip4base- 
 h1024-p63-s64512-cps-ndrpdr 

 1.  5.08 
 2.  5.08 

 64b-8t4c-avf-ethip4udp-ip4base- 
 h1024-p63-s64512-cps-ndrpdr 

 1.  4.27 
 2.  4.31

2n1l-25ge2p1xxv710-avf-ethip4udp-ip4base-h16384-p63-s1032192-cps-ndrpdr

CPS on empty UDP transactions with IPv4 routing

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /18 route entries. DUT1 tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional UDP flows) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp-ip4base- 
 h16384-p63-s1032192-cps-ndrpdr 

 1.  3.74 
 2.  3.74 

 64b-4t2c-avf-ethip4udp-ip4base- 
 h16384-p63-s1032192-cps-ndrpdr 

 1.  3.98 
 2.  4.00 

 64b-8t4c-avf-ethip4udp-ip4base- 
 h16384-p63-s1032192-cps-ndrpdr 

 1.  3.77 
 2.  3.81

2n1l-25ge2p1xxv710-avf-ethip4udp-ip4base-h262144-p63-s16515072-cps-ndrpdr

CPS on empty UDP transactions with IPv4 routing

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /14 route entries. DUT1 tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional UDP flows) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp-ip4base- 
 h262144-p63-s16515072-cps-ndrpdr 

 1.  3.70 
 2.  3.70 

 64b-4t2c-avf-ethip4udp-ip4base- 
 h262144-p63-s16515072-cps-ndrpdr 

 1.  3.44 
 2.  3.46 

 64b-8t4c-avf-ethip4udp-ip4base- 
 h262144-p63-s16515072-cps-ndrpdr 

 1.  3.68 
 2.  3.68

2n1l-25ge2p1xxv710-avf-ethip4udp-ip4base-h65536-p63-s4128768-cps-ndrpdr

CPS on empty UDP transactions with IPv4 routing

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /16 route entries. DUT1 tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional UDP flows) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp-ip4base- 
 h65536-p63-s4128768-cps-ndrpdr 

 1.  3.59 
 2.  3.81 

 64b-4t2c-avf-ethip4udp-ip4base- 
 h65536-p63-s4128768-cps-ndrpdr 

 1.  3.68 
 2.  3.68 

 64b-8t4c-avf-ethip4udp-ip4base- 
 h65536-p63-s4128768-cps-ndrpdr 

 1.  3.70 
 2.  3.70

2n1l-25ge2p1xxv710-avf-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr

RFC2544: Packet throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp- 
 ip4base-iacl50sf-10kflows-ndrpdr 

 1. 11.20       7.52 
 2. 11.25       7.56 
  
 3.   11   15   21        11   15   17  
 4.   20   31   36        19   29   35  
 5.   44   54   62        44   55   62  

 64b-4t2c-avf-ethip4udp- 
 ip4base-iacl50sf-10kflows-ndrpdr 

 1. 21.19      14.24 
 2. 21.83      14.67 
  
 3.   11   13   21        11   18   24  
 4.   21   27   33        21   27   32  
 5.   43   63   75        43   63   76  

 64b-8t4c-avf-ethip4udp- 
 ip4base-iacl50sf-10kflows-ndrpdr 

 1. 32.23      21.66 
 2. 34.57      23.23 
  
 3.   12   17   22        12   17   22  
 4.   21   32   48        21   33   50  
 5.   35   86  154        37   92  157

2n1l-25ge2p1xxv710-avf-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr

RFC2544: Packet throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp- 
 ip4base-iacl50sl-10kflows-ndrpdr 

 1.  8.98       6.03 
 2.  9.07       6.09 
  
 3.   11   17   21        11   14   18  
 4.   11   16   24        16   35   44  
 5.   51   63   72        51   63   71  

 64b-4t2c-avf-ethip4udp- 
 ip4base-iacl50sl-10kflows-ndrpdr 

 1. 14.77       9.92 
 2. 16.08      10.80 
  
 3.   12   19   24        11   18   27  
 4.   20   27   34        21   28   33  
 5.   51   76  102        51   76  103  

 64b-8t4c-avf-ethip4udp- 
 ip4base-iacl50sl-10kflows-ndrpdr 

 1. 20.02      13.45 
 2. 21.58      14.50 
  
 3.   11   15   20        11   17   22  
 4.   19   28   36        18   27   35  
 5.   31   89  147        31   90  149

2n1l-25ge2p1xxv710-avf-ethip4udp-ip4base-oacl50sf-10kflows-ndrpdr

RFC2544: Packet throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp- 
 ip4base-oacl50sf-10kflows-ndrpdr 

 1. 10.96       7.37 
 2. 11.09       7.46 
  
 3.   11   19   23        12   18   24  
 4.   20   28   34        20   29   33  
 5.   46   57   63        47   58   65  

 64b-4t2c-avf-ethip4udp- 
 ip4base-oacl50sf-10kflows-ndrpdr 

 1. 20.79      13.97 
 2. 21.21      14.25 
  
 3.   11   19   23        12   19   24  
 4.   22   28   35        23   29   36  
 5.   44   61   74        46   64   77  

 64b-8t4c-avf-ethip4udp- 
 ip4base-oacl50sf-10kflows-ndrpdr 

 1. 32.66      21.95 
 2. 34.68      23.31 
  
 3.   14   18   22        12   17   22  
 4.   22   32   42        21   32   42  
 5.   36   94  140        36   95  141

2n1l-25ge2p1xxv710-avf-ethip4udp-ip4base-oacl50sl-10kflows-ndrpdr

RFC2544: Packet throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp- 
 ip4base-oacl50sl-10kflows-ndrpdr 

 1.  8.76       5.89 
 2.  8.89       5.98 
  
 3.   11   17   19        11   16   22  
 4.   21   31   36        18   28   36  
 5.   53   63   70        53   64   73  

 64b-4t2c-avf-ethip4udp- 
 ip4base-oacl50sl-10kflows-ndrpdr 

 1. 14.57       9.79 
 2. 15.86      10.66 
  
 3.   12   19   28        11   18   23  
 4.   22   29   36        23   29   35  
 5.   53   79  105        53   79  106  

 64b-8t4c-avf-ethip4udp- 
 ip4base-oacl50sl-10kflows-ndrpdr 

 1. 19.18      12.89 
 2. 21.08      14.16 
  
 3.   12   18   22        12   17   22  
 4.   19   28   37        19   28   37  
 5.   32   84  135        32   85  136

2n1l-25ge2p1xxv710-avf-ethip4udp-nat44det-h1024-p63-s64512-ndrpdr

RFC2544: Pkt throughput NAT44 performance test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /22 and IPv4 /24 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1 flow per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp- 
 nat44det-h1024-p63-s64512-ndrpdr 

 1.  5.27       3.54 
 2.  5.46       3.67 
  
 3.   11   13   38        11   29   40  
 4.   12   33   50        16   44   56  
 5.   26   71   99        58   83  104  

 64b-4t2c-avf-ethip4udp- 
 nat44det-h1024-p63-s64512-ndrpdr 

 1.  6.44       4.33 
 2.  6.60       4.44 
  
 3.   11   13   21        11   17   23  
 4.   12   24   36        19   33   42  
 5.   16   55   78        53   72   89  

 64b-8t4c-avf-ethip4udp- 
 nat44det-h1024-p63-s64512-ndrpdr 

 1.  7.32       4.92 
 2.  7.55       5.07 
  
 3.   11   15   16        11   17   22  
 4.   12   20   33        21   33   41  
 5.   13   43   69        56   73   82

2n1l-25ge2p1xxv710-avf-ethip4udp-nat44det-h16384-p63-s1032192-ndrpdr

RFC2544: Pkt throughput NAT44 performance test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /18 and IPv4 /24 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1 flow per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp- 
 nat44det-h16384-p63-s1032192-ndrpdr 

 1.  6.44       4.33 
 2.  6.81       4.57 
  
 3.   11   13   21        12   18   26  
 4.   12   24   32        20   29   34  
 5.   33   52   84        34   53   85  

 64b-4t2c-avf-ethip4udp- 
 nat44det-h16384-p63-s1032192-ndrpdr 

 1. 10.43       7.01 
 2. 11.30       7.59 
  
 3.   12   19   24        12   21   26  
 4.   20   29   35        22   31   38  
 5.   34   60  113        40   67  121  

 64b-8t4c-avf-ethip4udp- 
 nat44det-h16384-p63-s1032192-ndrpdr 

 1. 17.16      11.53 
 2. 20.17      13.55 
  
 3.   11   18   23        12   18   24  
 4.   19   30   48        20   32   50  
 5.   30   73  343        32   76  351

2n1l-25ge2p1xxv710-avf-ethip4udp-nat44det-h262144-p63-s16515072-ndrpdr

RFC2544: Pkt throughput NAT44 performance test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /14 and IPv4 /24 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1 flow per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp- 
 nat44det-h262144-p63-s16515072-ndrpdr 

 1.  4.28       2.88 
 2.  4.76       3.20 
  
 3.   11   12   13        11   19   33  
 4.   40   54   66        34   48   61  
 5.   28   54  103        33   58  105  

 64b-4t2c-avf-ethip4udp- 
 nat44det-h262144-p63-s16515072-ndrpdr 

 1.  8.85       5.94 
 2.  9.73       6.54 
  
 3.   11   16   23        11   18   28  
 4.   21   31   40        20   31   40  
 5.   35   89  263        36   90  261  

 64b-8t4c-avf-ethip4udp- 
 nat44det-h262144-p63-s16515072-ndrpdr 

 1. 13.72       9.22 
 2. 15.63      10.50 
  
 3.   14   21   28        11   17   22  
 4.   18   26   39        18   27   40  
 5.   30   85  544        31   88  559

2n1l-25ge2p1xxv710-avf-ethip4udp-nat44det-h65536-p63-s4128758-ndrpdr

RFC2544: Pkt throughput NAT44 performance test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /16 and IPv4 /24 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1 flow per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp- 
 nat44det-h65536-p63-s4128758-ndrpdr 

 1.  4.85       3.26 
 2.  5.16       3.46 
  
 3.   11   17   20        11   13   19  
 4.   16   34   46        16   36   47  
 5.   47   69  112        43   70  122  

 64b-4t2c-avf-ethip4udp- 
 nat44det-h65536-p63-s4128758-ndrpdr 

 1.  9.76       6.56 
 2. 10.53       7.07 
  
 3.   11   18   29        11   17   28  
 4.   20   28   35        20   28   37  
 5.   37   71  121        38   73  122  

 64b-8t4c-avf-ethip4udp- 
 nat44det-h65536-p63-s4128758-ndrpdr 

 1. 14.83       9.97 
 2. 16.53      11.11 
  
 3.   11   16   21        11   17   24  
 4.   19   28   42        19   29   42  
 5.   29   77  277        29   79  267

2n1l-25ge2p1xxv710-avf-ethip4udp-nat44ed-h1024-p63-s64512-cps-ndrpdr

CPS on empty UDP transactions with NAT44ED

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and one static IPv4 /22 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional UDP flows) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: Benchmarking Methodology for Network Security Device Performance (draft-ietf-bmwg-ngfw-performance-03).

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp-nat44ed- 
 h1024-p63-s64512-cps-ndrpdr 

 1.  1.61 
 2.  1.61 

 64b-4t2c-avf-ethip4udp-nat44ed- 
 h1024-p63-s64512-cps-ndrpdr 

 1.  2.16 
 2.  2.16 

 64b-8t4c-avf-ethip4udp-nat44ed- 
 h1024-p63-s64512-cps-ndrpdr 

 1.  0.15 
 2.  2.93

2n1l-25ge2p1xxv710-avf-ethip4udp-nat44ed-h1024-p63-s64512-udir-ndrpdr

RFC2544: Pkt throughput NAT44 endpoint-dependent mode performance test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and one static IPv4 /8 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L4 flows (uni-directional UDP flows) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: Benchmarking Methodology for Network Security Device Performance (draft-ietf-bmwg-ngfw-performance-03).

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp-nat44ed- 
 h1024-p63-s64512-udir-ndrpdr 

 1.  7.02       4.71 
 2.  7.05       4.74 

 64b-4t2c-avf-ethip4udp-nat44ed- 
 h1024-p63-s64512-udir-ndrpdr 

 1.  9.50       6.38 
 2.  9.99       6.71 

 64b-8t4c-avf-ethip4udp-nat44ed- 
 h1024-p63-s64512-udir-ndrpdr 

 1. 11.31       7.60 
 2. 12.50       8.40

2n1l-25ge2p1xxv710-avf-ethip4udp-nat44ed-h16384-p63-s1032192-cps-ndrpdr

CPS on empty UDP transactions with NAT44ED

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and one static IPv4 /18 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional UDP flows) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: Benchmarking Methodology for Network Security Device Performance (draft-ietf-bmwg-ngfw-performance-03).

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp-nat44ed- 
 h16384-p63-s1032192-cps-ndrpdr 

 1.  1.00 
 2.  1.01 

 64b-4t2c-avf-ethip4udp-nat44ed- 
 h16384-p63-s1032192-cps-ndrpdr 

 1.  0.97 
 2.  1.67 

 64b-8t4c-avf-ethip4udp-nat44ed- 
 h16384-p63-s1032192-cps-ndrpdr 

 1.  2.20 
 2.  2.38

2n1l-25ge2p1xxv710-avf-ethip4udp-nat44ed-h16384-p63-s1032192-udir-ndrpdr

RFC2544: Pkt throughput NAT44 endpoint-dependent mode performance test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and one static IPv4 /8 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L4 flows (un-directional UDP flows) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: Benchmarking Methodology for Network Security Device Performance (draft-ietf-bmwg-ngfw-performance-03).

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp-nat44ed- 
 h16384-p63-s1032192-udir-ndrpdr 

 1.  5.17       3.47 
 2.  5.38       3.61 

 64b-4t2c-avf-ethip4udp-nat44ed- 
 h16384-p63-s1032192-udir-ndrpdr 

 1.  7.17       4.82 
 2.  7.73       5.19 

 64b-8t4c-avf-ethip4udp-nat44ed- 
 h16384-p63-s1032192-udir-ndrpdr 

 1.  6.96       4.68 
 2.  8.46       5.69

2n1l-25ge2p1xxv710-avf-ethip4udp-nat44ed-h262144-p63-s16515072-cps-ndrpdr

CPS on empty UDP transactions with NAT44ED

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and one static IPv4 /14 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional UDP flows) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: Benchmarking Methodology for Network Security Device Performance (draft-ietf-bmwg-ngfw-performance-03).

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp-nat44ed- 
 h262144-p63-s16515072-cps-ndrpdr 

 1.  0.51 
 2.  0.53 

 64b-4t2c-avf-ethip4udp-nat44ed- 
 h262144-p63-s16515072-cps-ndrpdr 

 1.  0.81 
 2.  0.95 

 64b-8t4c-avf-ethip4udp-nat44ed- 
 h262144-p63-s16515072-cps-ndrpdr 

 1.  1.38 
 2.  1.52

2n1l-25ge2p1xxv710-avf-ethip4udp-nat44ed-h262144-p63-s16515072-udir-ndrpdr

RFC2544: Pkt throughput NAT44 endpoint-dependent mode performance test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and one static IPv4 /8 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L4 flows (uni-directional UDP flows) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: Benchmarking Methodology for Network Security Device Performance (draft-ietf-bmwg-ngfw-performance-03).

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp-nat44ed- 
 h262144-p63-s16515072-udir-ndrpdr 

 1.  4.60       3.09 
 2.  4.67       3.14 

 64b-4t2c-avf-ethip4udp-nat44ed- 
 h262144-p63-s16515072-udir-ndrpdr 

 1.  6.04       4.06 
 2.  6.38       4.29 

 64b-8t4c-avf-ethip4udp-nat44ed- 
 h262144-p63-s16515072-udir-ndrpdr 

 1.  6.25       4.20 
 2.  7.34       4.93

2n1l-25ge2p1xxv710-avf-ethip4udp-nat44ed-h65536-p63-s4128768-cps-ndrpdr

CPS on empty UDP transactions with NAT44ED

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and one static IPv4 /16 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L7 flows (${cps} bi-directional UDP flows) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: Benchmarking Methodology for Network Security Device Performance (draft-ietf-bmwg-ngfw-performance-03).

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp-nat44ed- 
 h65536-p63-s4128768-cps-ndrpdr 

 1.  0.73 
 2.  0.81 

 64b-4t2c-avf-ethip4udp-nat44ed- 
 h65536-p63-s4128768-cps-ndrpdr 

 1.  1.34 
 2.  1.41 

 64b-8t4c-avf-ethip4udp-nat44ed- 
 h65536-p63-s4128768-cps-ndrpdr 

 1.  1.88 
 2.  2.06

2n1l-25ge2p1xxv710-avf-ethip4udp-nat44ed-h65536-p63-s4128768-udir-ndrpdr

RFC2544: Pkt throughput NAT44 endpoint-dependent mode performance test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and one static IPv4 /8 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contain L4 flows (uni-directional UDP flows) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: Benchmarking Methodology for Network Security Device Performance (draft-ietf-bmwg-ngfw-performance-03).

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-avf-ethip4udp-nat44ed- 
 h65536-p63-s4128768-udir-ndrpdr 

 1.  4.60       3.09 
 2.  4.71       3.17 

 64b-4t2c-avf-ethip4udp-nat44ed- 
 h65536-p63-s4128768-udir-ndrpdr 

 1.  6.37       4.28 
 2.  6.80       4.57 

 64b-8t4c-avf-ethip4udp-nat44ed- 
 h65536-p63-s4128768-udir-ndrpdr 

 1.  6.39       4.29 
 2.  7.92       5.32

2n1l-25ge2p1xxv710-ethip4-ip4base-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-ethip4-ip4base-ndrpdr 

 1. 15.19      10.21 
 2. 16.46      11.06 
  
 3.   11   28   39        11   26   43  
 4.   18   25   32        20   29   38  
 5.   48   61   73        48   61   74  

 64b-4t2c-ethip4-ip4base-ndrpdr 

 1. 30.63      20.58 
 2. 32.53      21.86 
  
 3.   13   31   34        14   36   44  
 4.   19   23   27        19   23   28  
 5.   47   59   73        48   60   72  

 64b-8t4c-ethip4-ip4base-ndrpdr 

 1. 33.51      22.52 
 2. 34.42      23.13 
  
 3.   13   25   32        15   24   31  
 4.   16   19   24        16   19   23  
 5.   20   23   26        20   24   27

2n1l-25ge2p1xxv710-ethip4-ip4scale200k-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c- 
 ethip4-ip4scale200k-ndrpdr 

 1. 13.92       9.35 
 2. 13.92       9.35 
  
 3.   12   28   37        14   31   42  
 4.   21   32   40        17   26   35  
 5.   37   47   58        38   48   57  

 64b-4t2c- 
 ethip4-ip4scale200k-ndrpdr 

 1. 26.41      17.75 
 2. 26.94      18.10 
  
 3.   14   32   41        16   30   40  
 4.   18   22   26        17   23   26  
 5.   37   46   56        38   47   57  

 64b-8t4c- 
 ethip4-ip4scale200k-ndrpdr 

 1. 35.31      23.73 
 2. 36.57      24.58 
  
 3.   16   28   39        17   31   39  
 4.   16   19   23        17   20   23  
 5.   23   27   31        23   28   32

2n1l-25ge2p1xxv710-ethip4-ip4scale200k-rnd-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains 2 randomized L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-ethip4- 
 ip4scale200k-rnd-ndrpdr 

 1. 13.12       8.82 
 2. 14.00       9.41 
  
 3.   12   35   44        17   36   42  
 4.   20   31   39        21   29   36  
 5.   50   64   86        50   64   87  

 64b-4t2c-ethip4- 
 ip4scale200k-rnd-ndrpdr 

 1. 26.03      17.49 
 2. 26.69      17.94 
  
 3.   16   33   42        17   31   41  
 4.   18   24   31        18   23   27  
 5.   41   52   65        41   53   65  

 64b-8t4c-ethip4- 
 ip4scale200k-rnd-ndrpdr 

 1. 35.13      23.60 
 2. 36.38      24.45 
  
 3.   17   32   41        17   33   41  
 4.   16   20   23        16   20   23  
 5.   24   28   33        24   28   33

2n1l-25ge2p1xxv710-ethip4-ip4scale20k-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and 2x10k static IPv4 /32 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c- 
 ethip4-ip4scale20k-ndrpdr 

 1. 14.34       9.63 
 2. 14.41       9.68 
  
 3.   12   25   41        14   34   42  
 4.   19   29   35        21   33   41  
 5.   37   47   56        39   49   57  

 64b-4t2c- 
 ethip4-ip4scale20k-ndrpdr 

 1. 27.53      18.50 
 2. 28.22      18.97 
  
 3.   15   30   40        15   31   41  
 4.   18   25   30        18   22   26  
 5.   39   47   54        39   47   54  

 64b-8t4c- 
 ethip4-ip4scale20k-ndrpdr 

 1. 34.21      22.99 
 2. 34.86      23.42 
  
 3.   14   28   41        15   31   40  
 4.   17   21   24        16   20   24  
 5.   24   28   33        24   29   32

2n1l-25ge2p1xxv710-ethip4-ip4scale20k-rnd-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and 2x10k static IPv4 /32 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains 2 randomized L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-ethip4- 
 ip4scale20k-rnd-ndrpdr 

 1. 13.92       9.35 
 2. 14.13       9.49 
  
 3.   14   32   43        11   21   40  
 4.   18   32   40        17   26   37  
 5.   38   48   57        39   50   60  

 64b-4t2c-ethip4- 
 ip4scale20k-rnd-ndrpdr 

 1. 27.88      18.74 
 2. 28.88      19.41 
  
 3.   14   30   41        15   34   41  
 4.   18   25   30        19   25   32  
 5.   41   51   61        41   51   61  

 64b-8t4c-ethip4- 
 ip4scale20k-rnd-ndrpdr 

 1. 34.13      22.93 
 2. 35.02      23.53 
  
 3.   15   27   39        20   32   39  
 4.   17   21   28        17   21   24  
 5.   22   26   30        22   26   30

2n1l-25ge2p1xxv710-ethip4-ip4scale2m-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and 2x1M static IPv4 /32 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c- 
 ethip4-ip4scale2m-ndrpdr 

 1. 12.46       8.38 
 2. 12.59       8.46 
  
 3.   11   26   34        13   36   44  
 4.   21   31   40        22   32   43  
 5.   40   51   59        42   53   61  

 64b-4t2c- 
 ethip4-ip4scale2m-ndrpdr 

 1. 22.36      15.02 
 2. 22.36      15.02 
  
 3.   15   34   42        16   31   38  
 4.   17   23   31        17   25   31  
 5.   35   43   51        35   43   51  

 64b-8t4c- 
 ethip4-ip4scale2m-ndrpdr 

 1. 32.60      21.91 
 2. 33.94      22.81 
  
 3.   16   26   33        15   28   37  
 4.   17   20   24        16   22   25  
 5.   24   28   31        24   28   31

2n1l-25ge2p1xxv710-ethip4-ip4scale2m-rnd-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and 2x1M static IPv4 /32 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUT1. TG traffic profile contains 2 randomized L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Throughput: 
 1.  Mpps       Gbps (NDR) 
 2.  Mpps       Gbps (PDR) 
 
 One-Way Latency Percentiles in uSec at %PDR load, 
 one set per each direction: 
 3.  P50  P90  P99       P50  P90  P99 (10% PDR) 
 4.  P50  P90  P99       P50  P90  P99 (50% PDR) 
 5.  P50  P90  P99       P50  P90  P99 (90% PDR) 

 64b-2t1c-ethip4- 
 ip4scale2m-rnd-ndrpdr 

 1. 10.78       7.24 
 2. 11.11       7.46 
  
 3.   11   32   43        15   33   42  
 4.   21   32   43        20   30   40  
 5.   43   56   69        43   56   68  

 64b-4t2c-ethip4- 
 ip4scale2m-rnd-ndrpdr 

 1. 20.93      14.07 
 2. 21.57      14.50 
  
 3.   13   29   36        15   32   43  
 4.   20   26   34        18   24   29  
 5.   40   52   65        41   53   64  

 64b-8t4c-ethip4- 
 ip4scale2m-rnd-ndrpdr 

 1. 36.03      24.21 
 2. 36.57      24.58 
  
 3.   16   31   39        16   33   41  
 4.   17   21   25        17   22   25  
 5.   30   37   45        30   37   44