container memif

10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr

RFC2544: Pkt throughput L2BD with memif and IEEE 802.1Q test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 bridge domain. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with two L2 bridge domains and MAC learning enabled. Container is connected to VPP via Memif interface. Container is running same VPP version as running on DUT. Container is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory constraints. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr No Data
64b-4t2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr No Data
64b-8t4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr No Data

10ge2p1x710-eth-l2bdbasemaclrn-eth-2memif-1lxc-ndrpdr

RFC2544: Pkt throughput L2BD test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 bridge domain.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with two L2 bridge domains and MAC learning enabled. LXC is connected to VPP via Memif interface. LXC is running same VPP version as running on DUT. LXC is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory constraints. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2bdbasemaclrn-eth-2memif-1lxc-ndrpdr No Data
64b-4t2c-eth-l2bdbasemaclrn-eth-2memif-1lxc-ndrpdr No Data
64b-8t4c-eth-l2bdbasemaclrn-eth-2memif-1lxc-ndrpdr No Data
imix-2t1c-eth-l2bdbasemaclrn-eth-2memif-1lxc-ndrpdr No Data
imix-4t2c-eth-l2bdbasemaclrn-eth-2memif-1lxc-ndrpdr No Data
imix-8t4c-eth-l2bdbasemaclrn-eth-2memif-1lxc-ndrpdr No Data

10ge2p1x710-eth-l2xcbase-eth-1memif-1dcr-ndrpdr

RFC2544: Pkt throughput L2XC test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
  • [Cfg] DUT configuration: DUT1 and DUT2 configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. Container is connected to VPP via Memif interface running same VPP version as running on DUT. Resources are limited via cgroup to use 5 cores allocated from pool of isolated CPUs. There are no memory contraints. Cross Horizontal topology with packets flowing via DUT (VPP) to Container, then via horizontal memif to the next Container, and so on until the last Container then to NIC (in last Container). Single Container is supported as of now.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2xcbase-eth-1memif-1dcr-ndrpdr No Data
64b-4t2c-eth-l2xcbase-eth-1memif-1dcr-ndrpdr No Data
64b-8t4c-eth-l2xcbase-eth-1memif-1dcr-ndrpdr No Data
imix-2t1c-eth-l2xcbase-eth-1memif-1dcr-ndrpdr No Data
imix-4t2c-eth-l2xcbase-eth-1memif-1dcr-ndrpdr No Data
imix-8t4c-eth-l2xcbase-eth-1memif-1dcr-ndrpdr No Data

10ge2p1x710-eth-l2xcbase-eth-2memif-1dcr-ndrpdr

RFC2544: Pkt throughput L2XC test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. Container is connected to VPP via Memif interface. Container is running same VPP version as running on DUT. Container is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory contraints.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2xcbase-eth-2memif-1dcr-ndrpdr No Data
64b-4t2c-eth-l2xcbase-eth-2memif-1dcr-ndrpdr No Data
64b-8t4c-eth-l2xcbase-eth-2memif-1dcr-ndrpdr No Data
imix-2t1c-eth-l2xcbase-eth-2memif-1dcr-ndrpdr No Data
imix-4t2c-eth-l2xcbase-eth-2memif-1dcr-ndrpdr No Data
imix-8t4c-eth-l2xcbase-eth-2memif-1dcr-ndrpdr No Data

10ge2p1x710-eth-l2xcbase-eth-2memif-1lxc-ndrpdr

RFC2544: Pkt throughput L2XC test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. LXC is connected to VPP via Memif interface. LXC is running same VPP version as running on DUT. LXC is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory contraints.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2xcbase-eth-2memif-1lxc-ndrpdr No Data
64b-4t2c-eth-l2xcbase-eth-2memif-1lxc-ndrpdr No Data
64b-8t4c-eth-l2xcbase-eth-2memif-1lxc-ndrpdr No Data
imix-2t1c-eth-l2xcbase-eth-2memif-1lxc-ndrpdr No Data
imix-4t2c-eth-l2xcbase-eth-2memif-1lxc-ndrpdr No Data
imix-8t4c-eth-l2xcbase-eth-2memif-1lxc-ndrpdr No Data

10ge2p1x710-ethip4-ip4base-eth-2memif-1dcr-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing with two FIB tables and two static IPv4 /24 route entries per FIB table. Container is connected to VPP via Memif interface. Container is running same VPP version as running on DUT. Container is limited via cgroup to use cores allocated from pool of isolated CPUs. There are no memory contraints. DUTs are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4-ip4base-eth-2memif-1dcr-ndrpdr No Data
64b-4t2c-ethip4-ip4base-eth-2memif-1dcr-ndrpdr No Data
64b-8t4c-ethip4-ip4base-eth-2memif-1dcr-ndrpdr No Data
imix-2t1c-ethip4-ip4base-eth-2memif-1dcr-ndrpdr No Data
imix-4t2c-ethip4-ip4base-eth-2memif-1dcr-ndrpdr No Data
imix-8t4c-ethip4-ip4base-eth-2memif-1dcr-ndrpdr No Data

ip4

10ge2p1x710-avf-eth-ip4base-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel with VF enabled.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-avf-eth-ip4base-ndrpdr No Data
64b-4t2c-avf-eth-ip4base-ndrpdr No Data
64b-8t4c-avf-eth-ip4base-ndrpdr No Data

10ge2p1x710-dot1q-ip4base-ndrpdr

RFC2544: Pkt throughput IPv4 routing with IEEE 802.1Q test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /30 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-dot1q-ip4base-ndrpdr No Data
64b-4t2c-dot1q-ip4base-ndrpdr No Data
64b-8t4c-dot1q-ip4base-ndrpdr No Data

10ge2p1x710-ethip4-ip4base-copwhtlistbase-ndrpdr

RFC2544: Pkt throughput IPv4 whitelist test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 COP security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4-ip4base-copwhtlistbase-ndrpdr No Data
64b-4t2c-ethip4-ip4base-copwhtlistbase-ndrpdr No Data
64b-8t4c-ethip4-ip4base-copwhtlistbase-ndrpdr No Data

10ge2p1x710-ethip4-ip4base-iacldstbase-ndrpdr

RFC2544: Pkt throughput IPv4 iAcl whitelist test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 iAcl security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4-ip4base-iacldstbase-ndrpdr No Data
64b-4t2c-ethip4-ip4base-iacldstbase-ndrpdr No Data
64b-8t4c-ethip4-ip4base-iacldstbase-ndrpdr No Data

10ge2p1x710-ethip4-ip4base-ipolicemarkbase-ndrpdr

RFC2544: Pkt throughput IPv4 policer test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries and policer with 2R3C color-aware configuration. Policer is applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544, RFC2698.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4-ip4base-ipolicemarkbase-ndrpdr No Data
64b-4t2c-ethip4-ip4base-ipolicemarkbase-ndrpdr No Data
64b-8t4c-ethip4-ip4base-ipolicemarkbase-ndrpdr No Data

10ge2p1x710-ethip4-ip4base-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4-ip4base-ndrpdr No Data
64b-4t2c-ethip4-ip4base-ndrpdr No Data
64b-8t4c-ethip4-ip4base-ndrpdr No Data

10ge2p1x710-ethip4-ip4scale200k-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4-ip4scale200k-ndrpdr No Data
64b-4t2c-ethip4-ip4scale200k-ndrpdr No Data
64b-8t4c-ethip4-ip4scale200k-ndrpdr No Data

10ge2p1x710-ethip4-ip4scale20k-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4-ip4scale20k-ndrpdr No Data
64b-4t2c-ethip4-ip4scale20k-ndrpdr No Data
64b-8t4c-ethip4-ip4scale20k-ndrpdr No Data

10ge2p1x710-ethip4-ip4scale2m-ndrpdr

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4-ip4scale2m-ndrpdr No Data
64b-4t2c-ethip4-ip4scale2m-ndrpdr No Data
64b-8t4c-ethip4-ip4scale2m-ndrpdr No Data

10ge2p1x710-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr

RFC2544: Pkt throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr No Data
64b-4t2c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr No Data
64b-8t4c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr No Data

10ge2p1x710-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr

RFC2544: Pkt throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr No Data
64b-4t2c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr No Data
64b-8t4c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr No Data

10ge2p1x710-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr

RFC2544: Pkt throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr No Data
64b-4t2c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr No Data
64b-8t4c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr No Data

10ge2p1x710-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr

RFC2544: Pkt throughput IPv4 test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr No Data
64b-4t2c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr No Data
64b-8t4c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr No Data

10ge2p1x710-ethip4udp-ip4base-nat44-ndrpdr

RFC2544: Pkt throughput NAT44 performance test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4udp-ip4base-nat44-ndrpdr No Data
64b-4t2c-ethip4udp-ip4base-nat44-ndrpdr No Data
64b-8t4c-ethip4udp-ip4base-nat44-ndrpdr No Data

10ge2p1x710-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr

RFC2544: Pkt throughput NAT44 performance test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr No Data
64b-4t2c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr No Data
64b-8t4c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr No Data

ip4 tunnels

10ge2p1x710-dot1q–ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr

RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-Dot1Q-IPv4 for L2 switching of IPv4 on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with 100 L2 bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, up to 64,5k flows per flow-group) with all packets containing Ethernet header, IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-dot1q–ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr No Data
64b-4t2c-dot1q–ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr No Data
64b-8t4c-dot1q–ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr No Data

10ge2p1x710-dot1q–ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr

RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-Dot1Q-IPv4 for L2 switching of IPv4 on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with 10 L2 bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, up to 64,5k flows per flow-group) with all packets containing Ethernet header, IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-dot1q–ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr No Data
64b-4t2c-dot1q–ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr No Data
64b-8t4c-dot1q–ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr No Data

10ge2p1x710-dot1q–ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr

RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-Dot1Q-IPv4 for L2 switching of IPv4 on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with 1k L2 bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, up to 64,5k flows per flow-group) with all packets containing Ethernet header, IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-dot1q–ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr No Data
64b-4t2c-dot1q–ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr No Data
64b-8t4c-dot1q–ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr No Data

10ge2p1x710-dot1q–ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr

RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-Dot1Q-IPv4 for L2 switching of IPv4 on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with 1 L2 bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, up to 64,5k flows per flow-group) with all packets containing Ethernet header, IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-dot1q–ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr No Data
64b-4t2c-dot1q–ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr No Data
64b-8t4c-dot1q–ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr No Data

10ge2p1x710-ethip4lispip4-ip4base-ndrpdr

RFC2544: Pkt throughput Lisp test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv4 on DUT1-DUT2, Eth-IPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC6830.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4lispip4-ip4base-ndrpdr No Data
64b-4t2c-ethip4lispip4-ip4base-ndrpdr No Data
64b-8t4c-ethip4lispip4-ip4base-ndrpdr No Data

10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-ndrpdr

RFC2544: Pkt throughput L2BD with VXLANoIPv4 test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4 on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4vxlan-l2bdbasemaclrn-ndrpdr No Data
64b-4t2c-ethip4vxlan-l2bdbasemaclrn-ndrpdr No Data
64b-8t4c-ethip4vxlan-l2bdbasemaclrn-ndrpdr No Data

10ge2p1x710-ethip4vxlan-l2xcbase-ndrpdr

RFC2544: Pkt throughput L2XC with VXLANoIPv4 test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross-connect on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. VXLAN tunnels are configured between L2XCs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4vxlan-l2xcbase-ndrpdr No Data
64b-4t2c-ethip4vxlan-l2xcbase-ndrpdr No Data
64b-8t4c-ethip4vxlan-l2xcbase-ndrpdr No Data

ip6

10ge2p1x710-ethip6-ip6base-copwhtlistbase-ndrpdr

RFC2544: Pkt throughput IPv6 whitelist test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 COP security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
78b-2t1c-ethip6-ip6base-copwhtlistbase-ndrpdr No Data
78b-4t2c-ethip6-ip6base-copwhtlistbase-ndrpdr No Data
78b-8t4c-ethip6-ip6base-copwhtlistbase-ndrpdr No Data

10ge2p1x710-ethip6-ip6base-iacldstbase-ndrpdr

RFC2544: Pkt throughput IPv6 iAcl whitelist test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 iAcl security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
78b-2t1c-ethip6-ip6base-iacldstbase-ndrpdr No Data
78b-4t2c-ethip6-ip6base-iacldstbase-ndrpdr No Data
78b-8t4c-ethip6-ip6base-iacldstbase-ndrpdr No Data

10ge2p1x710-ethip6-ip6base-ndrpdr

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
78b-2t1c-ethip6-ip6base-ndrpdr No Data
78b-4t2c-ethip6-ip6base-ndrpdr No Data
78b-8t4c-ethip6-ip6base-ndrpdr No Data

10ge2p1x710-ethip6-ip6scale200k-ndrpdr

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x100k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
78b-2t1c-ethip6-ip6scale200k-ndrpdr No Data
78b-4t2c-ethip6-ip6scale200k-ndrpdr No Data
78b-8t4c-ethip6-ip6scale200k-ndrpdr No Data

10ge2p1x710-ethip6-ip6scale20k-ndrpdr

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
78b-2t1c-ethip6-ip6scale20k-ndrpdr No Data
78b-4t2c-ethip6-ip6scale20k-ndrpdr No Data
78b-8t4c-ethip6-ip6scale20k-ndrpdr No Data

10ge2p1x710-ethip6-ip6scale2m-ndrpdr

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x1M static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
78b-2t1c-ethip6-ip6scale2m-ndrpdr No Data
78b-4t2c-ethip6-ip6scale2m-ndrpdr No Data
78b-8t4c-ethip6-ip6scale2m-ndrpdr No Data

l2

10ge2p1x710-avf-eth-l2bdbasemaclrn-ndrpdr

RFC2544: Pkt throughput L2BD test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 bridge-domain.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel with VF enabled.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-avf-eth-l2bdbasemaclrn-ndrpdr No Data
64b-4t2c-avf-eth-l2bdbasemaclrn-ndrpdr No Data
64b-8t4c-avf-eth-l2bdbasemaclrn-ndrpdr No Data

10ge2p1x710-avf-eth-l2patch-ndrpdr

RFC2544: Pkt throughput L2patch test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 patch DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel with VF enabled.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-avf-eth-l2patch-ndrpdr No Data
64b-4t2c-avf-eth-l2patch-ndrpdr No Data
64b-8t4c-avf-eth-l2patch-ndrpdr No Data

10ge2p1x710-avf-eth-l2xcbase-ndrpdr

RFC2544: Pkt throughput L2XC test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross-connect.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel with VF enabled.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-avf-eth-l2xcbase-ndrpdr No Data
64b-4t2c-avf-eth-l2xcbase-ndrpdr No Data
64b-8t4c-avf-eth-l2xcbase-ndrpdr No Data

10ge2p1x710-dot1q-l2bdbasemaclrn-ndrpdr

RFC2544: Pkt throughput L2BD with IEEE 802.1Q test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge domain and MAC learning enabled. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-dot1q-l2bdbasemaclrn-ndrpdr No Data
64b-4t2c-dot1q-l2bdbasemaclrn-ndrpdr No Data
64b-8t4c-dot1q-l2bdbasemaclrn-ndrpdr No Data

10ge2p1x710-dot1q-l2xcbase-ndrpdr

RFC2544: Pkt throughput L2XC with IEEE 802.1Q test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-dot1q-l2xcbase-ndrpdr No Data
64b-4t2c-dot1q-l2xcbase-ndrpdr No Data
64b-8t4c-dot1q-l2xcbase-ndrpdr No Data

10ge2p1x710-eth-l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr

RFC2544: Pkt throughput L2BD test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr No Data
64b-4t2c-eth-l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr No Data
64b-8t4c-eth-l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr No Data

10ge2p1x710-eth-l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr

RFC2544: Pkt throughput L2BD test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr No Data
64b-4t2c-eth-l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr No Data
64b-8t4c-eth-l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr No Data

10ge2p1x710-eth-l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr

RFC2544: Pkt throughput L2BD test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr No Data
64b-4t2c-eth-l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr No Data
64b-8t4c-eth-l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr No Data

10ge2p1x710-eth-l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr

RFC2544: Pkt throughput L2BD test cases with ACL

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr No Data
64b-4t2c-eth-l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr No Data
64b-8t4c-eth-l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr No Data

10ge2p1x710-eth-l2bdbasemaclrn-ndrpdr

RFC2544: Pkt throughput L2BD test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2bdbasemaclrn-ndrpdr No Data
64b-4t2c-eth-l2bdbasemaclrn-ndrpdr No Data
64b-8t4c-eth-l2bdbasemaclrn-ndrpdr No Data

10ge2p1x710-eth-l2bdscale100kmaclrn-ndrpdr

RFC2544: Pkt throughput for L2BD test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 50k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2bdscale100kmaclrn-ndrpdr No Data
64b-4t2c-eth-l2bdscale100kmaclrn-ndrpdr No Data
64b-8t4c-eth-l2bdscale100kmaclrn-ndrpdr No Data

10ge2p1x710-eth-l2bdscale10kmaclrn-ndrpdr

RFC2544: Pkt throughput for L2BD test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 5k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2bdscale10kmaclrn-ndrpdr No Data
64b-4t2c-eth-l2bdscale10kmaclrn-ndrpdr No Data
64b-8t4c-eth-l2bdscale10kmaclrn-ndrpdr No Data

10ge2p1x710-eth-l2bdscale1mmaclrn-ndrpdr

RFC2544: Pkt throughput for L2BD test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 500k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2bdscale1mmaclrn-ndrpdr No Data
64b-4t2c-eth-l2bdscale1mmaclrn-ndrpdr No Data
64b-8t4c-eth-l2bdscale1mmaclrn-ndrpdr No Data

10ge2p1x710-eth-l2patch-ndrpdr

RFC2544: Pkt throughput L2patch test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 patch DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header,IPv4 header with static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2patch-ndrpdr No Data
64b-4t2c-eth-l2patch-ndrpdr No Data
64b-8t4c-eth-l2patch-ndrpdr No Data

10ge2p1x710-eth-l2xcbase-ndrpdr

RFC2544: Pkt throughput L2XC test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2xcbase-ndrpdr No Data
64b-4t2c-eth-l2xcbase-ndrpdr No Data
64b-8t4c-eth-l2xcbase-ndrpdr No Data

vm vhost

10ge2p1x710-1lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr

RFC2544: Pkt throughput L2BD test cases with vhost and vpp link bonding

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with VPP link bonding (mode LACP, transmit policy l34) on link between DUT1 and DUT2 and L2 bridge-domain with MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 Fortville by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-1lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-4t2c-1lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-8t4c-1lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-2t1c-1lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-4t2c-1lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-8t4c-1lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data

10ge2p1x710-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr

RFC2544: Pkt throughput L2XC test cases with vhost and vpp link bonding

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with VPP link bonding (mode LACP, transmit policy l34) on link between DUT1 and DUT2 and L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 Fortville by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-4t2c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-8t4c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-2t1c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-4t2c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-8t4c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data

10ge2p1x710-2lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr

RFC2544: Pkt throughput L2BD test cases with vhost and vpp link bonding

  • [Top] Network Topologies: TG-DUT1=DUT2-TG 3-node circular topology with single links between TG and DUT nodes and double link between DUT nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with VPP link bonding (mode LACP, transmit policy l34) on link between DUT1 and DUT2 and L2 bridge-domain with MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 Fortville by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-2lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-4t2c-2lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-8t4c-2lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-2t1c-2lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-4t2c-2lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-8t4c-2lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data

10ge2p1x710-2lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr

RFC2544: Pkt throughput L2XC test cases with vhost and vpp link bonding

  • [Top] Network Topologies: TG-DUT1=DUT2-TG 3-node circular topology with single links between TG and DUT nodes and double link between DUT nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with VPP link bonding (mode LACP, transmit policy l34) on link between DUT1 and DUT2 and L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 Fortville by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-2lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-4t2c-2lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-8t4c-2lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-2t1c-2lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-4t2c-2lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-8t4c-2lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data

10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr

RFC2544: Pkt throughput L2BD with vhost abd IEEE 802.1Q test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces, forwarding mode is set to io, rxd/txd=1024. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-4t2c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-8t4c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-2t1c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-4t2c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-8t4c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data

10ge2p1x710-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr

RFC2544: Pkt throughput L2XC test cases with vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-4t2c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-8t4c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-2t1c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-4t2c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-8t4c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data

10ge2p1x710-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr

RFC2544: Pkt throughput L2BD test cases with vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus on NUMA1 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-4t2c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-8t4c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-2t1c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-4t2c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-8t4c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data

10ge2p1x710-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-ndrpdr

RFC2544: Pkt throughput L2BD test cases with vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domains and MAC learning enabled. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 6-10 and 11-15 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-ndrpdr No Data
64b-4t2c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-ndrpdr No Data
64b-8t4c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-ndrpdr No Data
imix-2t1c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-ndrpdr No Data
imix-4t2c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-ndrpdr No Data
imix-8t4c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-ndrpdr No Data

10ge2p1x710-eth-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr

RFC2544: Pkt throughput L2XC test cases with vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-4t2c-eth-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-8t4c-eth-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-2t1c-eth-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-4t2c-eth-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-8t4c-eth-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr No Data

10ge2p1x710-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrpdr

RFC2544: Pkt throughput L2XC test cases with vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connects. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 6-10 and 11-15 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrpdr No Data
64b-4t2c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrpdr No Data
64b-8t4c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrpdr No Data
imix-2t1c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrpdr No Data
imix-4t2c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrpdr No Data
imix-8t4c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrpdr No Data

10ge2p1x710-ethip4-ip4base-eth-2vhostvr1024-1vm-ndrpdr

RFC2544: Pkt throughput IPv4 test cases with vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to mac, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4-ip4base-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-4t2c-ethip4-ip4base-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-8t4c-ethip4-ip4base-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-2t1c-ethip4-ip4base-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-4t2c-ethip4-ip4base-eth-2vhostvr1024-1vm-ndrpdr No Data
imix-8t4c-ethip4-ip4base-eth-2vhostvr1024-1vm-ndrpdr No Data

10ge2p1x710-ethip4-ip4base-eth-4vhostvr1024-2vm-ndrpdr

RFC2544: Pkt throughput IPv4 test cases with vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnectingvhost-user interfaces using 5 cores pinned to cpus 6-10 and 11-15 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4-ip4base-eth-4vhostvr1024-2vm-ndrpdr No Data
64b-4t2c-ethip4-ip4base-eth-4vhostvr1024-2vm-ndrpdr No Data
64b-8t4c-ethip4-ip4base-eth-4vhostvr1024-2vm-ndrpdr No Data
imix-2t1c-ethip4-ip4base-eth-4vhostvr1024-2vm-ndrpdr No Data
imix-4t2c-ethip4-ip4base-eth-4vhostvr1024-2vm-ndrpdr No Data
imix-8t4c-ethip4-ip4base-eth-4vhostvr1024-2vm-ndrpdr No Data

10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr

RFC2544: Pkt throughput L2BD test cases with VXLANoIPv4 and vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC7348.
Name VPP API Test Commands History - Commands Used Per Test Case
64b-2t1c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-4t2c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data
64b-8t4c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr No Data