.. _mplsfib: MPLS FIB -------- Implementation ^^^^^^^^^^^^^^^ The MPLS FIB is implemented using exactly the same data structures as the IP FIB. The only difference is the implementation of the table. Whereas for IPv4 this is an mtrie and for IPv6 a hash table, for MPLS it is a flat array indexed by a 21 bit key (label & EOS bit). This implementation is chosen to favour packet forwarding speed. It can be the case in MPLS forwarding that packets received with the EOS bit set in the MPLS label need to be forwarded differently from those without. The most common example of this is if the path set contains a path that does not have an output label. In this case the non-EOS packets cannot take this path, because to do so would expose the neighbouring router to a label that it did not allocate. The design choice to make with an MPLS FIB table is therefore: - 20 bit key: label only. When the EOS and non-EOS actions differ the result is a 'EOS-choice' object. - 21 bit key: label and EOS-bit. The result is then the specific action based on EOS-bit. 20 bit key - Advantages:lower memory overhead, since there are few DB entries. - Disadvantages: slower DP performance in the case the path-lists differ, as more objects are encountered in the switch path 21 bit key - Advantages: faster DP performance Disadvantages: increased memory footprint. Switching between schemes based on observed/measured action similarity is not considered on the grounds of complexity and flip-flopping. VPP mantra - favour performance over memory. We choose a 21 bit key. Basics ^^^^^^ MPLS is not enabled by default. There are two steps to get started. First, create the default MPLS FIB: .. code-block:: console $ mpls table add 0 With '0' being the magic number for the 'default' table (just like it is for IPv[46]). One can create other MPLS tables, but, unlike IP tables, one cannot 'bind' non-default MPLS tables to interfaces, in other words all MPLS packets received on an interface will always result in a lookup in the default table. One has to be more inventive to use the non-default tables... Secondly, for *each* interface on which you wish to *receive* MPLS packets, that interface must be MPLS 'enabled' .. code-block:: console $ set interface mpls GigEthernet0/0/0 enable there is no equivalent enable for transmit, all that is required is to use an interface as an egress path. Entries in the MPLS FIB can be displayed with: .. code-block:: console $ sh mpls fib [table X] [label] There is a tight coupling between IP and MPLS forwarding. MPLS forwarding equivalence classes (FECs) are often an IP prefix – that is to say that traffic matching a given IP prefix is routed into a MPLS label switch path (LSP). It is thus necessary to be able to associate a given prefix/route with an [out-going] MPLS label that will be imposed when the packet is forwarded. This is configured as: .. code-block:: console $ ip route add 1.1.1.1/32 via 10.10.10.10 GigEthernet0/0/0 out-labels 33 packets matching 1.1.1.1/32 will be forwarded out GigEthernet0/0/0 and have MPLS label 33 imposed. More than one out-going label can be specified. Out-going MPLS labels can be applied to recursive and non-recursive routes, e.g; .. code-block:: console $ ip route add 2.2.2.0/24 via 1.1.1.1 out-labels 34 packets matching 2.2.2.0/24 will thus have two MPLS labels imposed; 34 and 33. This is the realisation of, e,g, an MPLS BGP VPNv4. To associate/allocate a local-label for a prefix, and thus have packets to that local-label forwarded equivalently to the prefix do; .. code-block:: console $ mpls local-label 99 2.2.2.0/24 In the API this action is called a ‘bind’. The router receiving the MPLS encapsulated packets needs to be programmed with actions associated which each label value – this is the role of the MPLS FIB. The MPLS FIB is a table, whose key is the MPLS label value and end-of-stack (EOS) bit, which stores the action to perform on packets with matching encapsulation. Currently supported actions are: #. Pop the label and perform an IPv[46] lookup in a specified table #. Pop the label and forward via a specified next-hop (this is penultimate-hop-pop, PHP) #. Swap the label and forward via a specified next-hop. These can be programmed respectively by: .. code-block:: console $ mpls local-label 33 eos ip4-lookup-in-table X $ mpls local-label 33 [eos] via 10.10.10.10 GigEthernet0/0/0 $ mpls local-label 33 [eos] via 10.10.10.10 GigEthernet0/0/0 out-labels 66 the latter is an example of an MPLS cross connect. Any description of a next-hop, recursive, non-recursive, labelled, non-labelled, etc, that is valid for an IP prefix, is also valid for an MPLS local-label. Note the use of the 'eos' keyword which indicates the programming is for the case when the label is end-of-stack. The last two operations can apply to both eos and non-eos packets, but the pop and IP lookup only to an eos packet. MPLS VPN ^^^^^^^^ To configure an MPLS VPN for a PE the following example can be used. Step 1; Configure routes to the iBGP peers - note these route MUST have out-going labels; .. code-block:: console $ ip route add 10.0.0.1/32 via 192.168.1.2 Eth0 out-labels 33 $ ip route add 10.0.0.2/32 via 192.168.2.2 Eth0 out-labels 34 Step 2; Configure the customer 'VRF' .. code-block:: console $ ip table add 2 Step 3; add a route via the iBGP peer[s] with the MPLS label advertised by that peer .. code-block:: console $ ip route add table 2 10.10.10.0/24 via 10.0.0.2 next-hop-table 0 out-label 122 $ ip route add table 2 10.10.10.0/24 via 10.0.0.1 next-hop-table 0 out-label 121 Step 4; add a route via the eBGP peer .. code-block:: console $ ip route add table 2 10.10.20.0/24 via 172.16.0.1 next-hop-table 2 Step 5; depending on the label allocation scheme used, add routes to the MPLS FIB to accept incoming labelled packets: #. per-prefix label scheme - this command 'binds' the label to the same forwarding as the IP route .. code-block:: console $ mpls local-label 99 10.10.20.0/24 #. per-CE label scheme - this pops the incoming label and forwards via the next-hop provided. Append config for 'out-labels' if so desired. .. code-block:: console $ mpls local-label 99 via 172.16.0.1 next-hop-table 2 #. per-VRF label scheme .. code-block:: console $ mpls local-label 99 via ip4-lookup-in-table 2 MPLS Tunnels ^^^^^^^^^^^^ MPLS tunnels are unidirectional and can impose a stack of labels. They are 'normal' interfaces and thus can be used, for example, as the target for IP routes and L2 cross-connects. To construct a tunnel: .. code-block:: console $ mpls tunnel add via 10.10.10.10 GigEthernet0/0/0 out-labels 33 44 55 and to then have that created tunnel to perform ECMP: .. code-block:: console $ mpls tunnel add mpls-tunnel0 via 10.10.10.11 GigEthernet0/0/0 out-labels 66 77 88 use .. code-block:: console $ sh mpls tunnel [X] to see the monster you have created. An MPLS tunnel interface is an interface like any other and now ready for use with the usual set of interface commands, e.g.: .. code-block:: console $ set interface state mpls-tunnel0 up $ set interface ip address mpls-tunnel0 192.168.1.1/30 $ ip route 1.1.1.1/32 via mpls-tunnel0