2n-zn2-xxv710

2n1l-25ge2p1xxv710-avf-dot1q-l2bdbasemaclrn-mrr

RFC2544: Pkt throughput L2BD with IEEE 802.1Q test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Dot1q-IPv4 for L2 switching of IPv4. IEEE 802.1Q tagging is applied on both links TG-DUT1.

  • [Cfg] DUT configuration: DUT1 is configured with: 2 VLAN subinterfaces (VID 100 and 200), 1 L2 BD with the 2 VLAN subinterfaces. DUT1 is tested with Intel-XXV710 with VF enabled.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-2t1c-avf- 
dot1q-l2bdbasemaclrn-mrr

 [18.14, 18.05, 18.05, 18.05, 18.11, 18.09, 18.13, 18.04, 18.09, 18.13] 

 64b-4t2c-avf- 
dot1q-l2bdbasemaclrn-mrr

 [35.67, 35.64, 35.61, 35.62, 35.66, 35.71, 35.54, 35.58, 35.49, 35.61] 

 64b-8t4c-avf- 
dot1q-l2bdbasemaclrn-mrr

 [35.76, 34.89, 34.93, 35.21, 36.16, 35.15, 34.77, 34.64, 34.74, 35.25] 

2n1l-25ge2p1xxv710-avf-eth-l2bdbasemaclrn-mrr

RFC2544: Pkt throughput L2BD test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 is configured with L2 and MAC learning enabled. DUT1 is tested with Intel-XXV710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-2t1c-avf- 
eth-l2bdbasemaclrn-mrr

 [28.20, 28.29, 28.31, 28.30, 28.33, 28.53, 28.25, 28.24, 28.25, 28.25] 

 64b-4t2c-avf- 
eth-l2bdbasemaclrn-mrr

 [36.95, 37.09, 37.04, 37.17, 36.92, 37.03, 37.00, 36.97, 37.11, 37.08] 

 64b-8t4c-avf- 
eth-l2bdbasemaclrn-mrr

 [33.35, 35.62, 33.51, 33.56, 33.51, 33.74, 33.01, 33.90, 32.93, 33.86] 

2n1l-25ge2p1xxv710-avf-eth-l2bdscale100kmaclrn-mrr

RFC2544: Pkt throughput for L2BD test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 is configured with L2 and MAC learning enabled. DUT1 is tested with Intel-XXV710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 50k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows:

port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-2t1c-avf- 
eth-l2bdscale100kmaclrn-mrr

 [22.44, 22.36, 22.23, 22.30, 22.53, 22.61, 22.33, 22.46, 22.32, 22.91] 

 64b-4t2c-avf- 
eth-l2bdscale100kmaclrn-mrr

 [37.36, 37.34, 37.31, 37.31, 37.30, 37.28, 37.29, 37.30, 37.30, 37.31] 

 64b-8t4c-avf- 
eth-l2bdscale100kmaclrn-mrr

 [36.66, 36.85, 36.66, 36.77, 36.81, 36.71, 36.64, 36.56, 36.87, 36.80] 

2n1l-25ge2p1xxv710-avf-eth-l2bdscale10kmaclrn-mrr

RFC2544: Pkt throughput for L2BD test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 is configured with L2 and MAC learning enabled. DUT1 is tested with Intel-XXV710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 5k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows:

port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-2t1c-avf- 
eth-l2bdscale10kmaclrn-mrr

 [23.39, 23.29, 23.38, 23.47, 23.44, 23.42, 23.40, 23.30, 23.38, 23.55] 

 64b-4t2c-avf- 
eth-l2bdscale10kmaclrn-mrr

 [37.44, 37.33, 37.33, 37.33, 37.33, 37.33, 37.32, 37.33, 37.33, 37.33] 

 64b-8t4c-avf- 
eth-l2bdscale10kmaclrn-mrr

 [34.86, 34.12, 33.67, 35.24, 34.64, 33.92, 34.79, 36.11, 34.73, 33.97] 

2n1l-25ge2p1xxv710-avf-eth-l2patch-mrr

RFC2544: Pkt throughput L2patch test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.

  • [Cfg] DUT configuration: DUT1 is configured with L2 patch DUT1 is tested with Intel-XXV710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with static payload MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-2t1c-avf-eth-l2patch-mrr 

 [37.15, 37.00, 37.22, 37.22, 37.25, 37.25, 37.24, 37.19, 37.25, 37.01] 

 64b-4t2c-avf-eth-l2patch-mrr 

 [34.07, 33.94, 33.56, 34.77, 33.85, 33.90, 34.34, 34.92, 34.33, 34.54] 

 64b-8t4c-avf-eth-l2patch-mrr 

 [33.65, 33.69, 33.59, 33.62, 33.60, 33.64, 33.60, 33.56, 33.58, 33.67] 

2n1l-25ge2p1xxv710-avf-eth-l2xcbase-mrr

RFC2544: Pkt throughput L2XC test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 is configured with L2 DUT1 is tested with Intel-XXV710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with static payload MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-2t1c-avf-eth-l2xcbase-mrr 

 [37.33, 37.35, 37.38, 37.38, 37.36, 37.34, 37.36, 37.36, 37.35, 37.31] 

 64b-4t2c-avf-eth-l2xcbase-mrr 

 [36.26, 36.75, 36.30, 36.29, 35.90, 36.90, 36.45, 36.36, 36.03, 36.99] 

 64b-8t4c-avf-eth-l2xcbase-mrr 

 [32.60, 32.14, 32.01, 33.04, 32.41, 32.24, 32.32, 32.41, 32.23, 32.73] 

2n1l-25ge2p1xxv710-eth-l2bdbasemaclrn-mrr

RFC2544: Pkt throughput L2BD test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 is configured with L2 and MAC learning enabled. DUT1 is tested with Intel-XXV710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-2t1c- 
eth-l2bdbasemaclrn-mrr

 [23.21, 23.30, 23.30, 23.32, 23.36, 23.30, 23.32, 23.36, 23.29, 23.29] 

 64b-4t2c- 
eth-l2bdbasemaclrn-mrr

 [33.56, 33.64, 33.78, 33.58, 33.64, 33.89, 33.63, 33.80, 33.61, 33.63] 

 64b-8t4c- 
eth-l2bdbasemaclrn-mrr

 [36.46, 36.56, 36.34, 36.34, 36.51, 36.63, 36.70, 36.51, 36.64, 36.62] 

2n1l-25ge2p1xxv710-eth-l2bdscale100kmaclrn-mrr

RFC2544: Pkt throughput for L2BD test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 is configured with L2 and MAC learning enabled. DUT1 is tested with Intel-XXV710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 50k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows:

port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-2t1c- 
eth-l2bdscale100kmaclrn-mrr

 [14.07, 14.21, 14.11, 14.05, 14.22, 14.00, 14.02, 14.26, 14.08, 14.27] 

 64b-4t2c- 
eth-l2bdscale100kmaclrn-mrr

 [21.87, 21.92, 21.26, 21.34, 21.40, 21.49, 21.83, 21.49, 21.42, 21.47] 

 64b-8t4c- 
eth-l2bdscale100kmaclrn-mrr

 [37.36, 37.27, 37.28, 37.22, 37.12, 37.07, 37.08, 37.21, 37.07, 37.27] 

2n1l-25ge2p1xxv710-eth-l2bdscale10kmaclrn-mrr

RFC2544: Pkt throughput for L2BD test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 is configured with L2 and MAC learning enabled. DUT1 is tested with Intel-XXV710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 5k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows:

port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-2t1c- 
eth-l2bdscale10kmaclrn-mrr

 [18.60, 18.59, 18.68, 18.66, 18.63, 18.69, 18.69, 18.67, 18.61, 18.67] 

 64b-4t2c- 
eth-l2bdscale10kmaclrn-mrr

 [27.97, 28.15, 28.16, 28.05, 28.08, 28.04, 28.13, 27.87, 28.08, 28.09] 

 64b-8t4c- 
eth-l2bdscale10kmaclrn-mrr

 [36.57, 36.54, 36.52, 36.50, 36.50, 36.52, 36.50, 36.47, 36.54, 36.54] 

2n1l-25ge2p1xxv710-eth-l2patch-mrr

RFC2544: Pkt throughput L2patch test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.

  • [Cfg] DUT configuration: DUT1 is configured with L2 patch DUT1 is tested with Intel-XXV710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with static payload MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-2t1c-eth-l2patch-mrr 

 [37.37, 37.36, 37.41, 37.33, 37.40, 37.36, 37.32, 37.40, 37.40, 37.33] 

 64b-4t2c-eth-l2patch-mrr 

 [37.27, 37.24, 37.23, 37.14, 37.15, 37.15, 37.23, 37.15, 37.18, 37.27] 

 64b-8t4c-eth-l2patch-mrr 

 [33.14, 33.08, 33.14, 33.46, 33.30, 32.97, 33.07, 33.11, 33.11, 33.21] 

2n1l-25ge2p1xxv710-eth-l2xcbase-mrr

RFC2544: Pkt throughput L2XC test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.

  • [Cfg] DUT configuration: DUT1 is configured with L2 DUT1 is tested with Intel-XXV710.

  • [Ver] TG vefication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with static payload MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 64b-2t1c-eth-l2xcbase-mrr 

 [29.50, 29.53, 29.51, 29.45, 29.54, 29.57, 29.61, 29.62, 29.53, 29.53] 

 64b-4t2c-eth-l2xcbase-mrr 

 [36.10, 36.05, 36.04, 36.04, 36.06, 36.02, 35.97, 35.98, 36.02, 35.98] 

 64b-8t4c-eth-l2xcbase-mrr 

 [35.24, 35.13, 35.30, 35.24, 35.25, 35.44, 35.35, 35.35, 35.43, 35.43]