3n-skx-xxv710

25ge2p1xxv710-avf-ethip4ipsec10000tnlsw-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  2.50       3.24 
2. 2.54 3.29

3. 78 190 308 62 191 306
4. 127 202 301 154 252 338
5. 134 166 251 174 236 306

 1518b-2t1c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  0.68       8.85 
2. 0.70 8.99

3. 145 266 377 139 252 363
4. 166 261 385 169 299 388
5. 317 413 476 304 379 458

 imix-2t1c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  1.52       5.49 
2. 1.55 5.60

25ge2p1xxv710-avf-ethip4ipsec10000tnlsw-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.29       4.74 
2. 4.38 4.84

3. 77 160 264 82 184 271
4. 52 82 112 51 83 105
5. 117 138 165 119 143 181

 64b-4t2c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  8.19       9.05 
2. 8.44 9.32

3. 66 168 217 89 188 278
4. 50 68 81 52 73 91
5. 109 128 147 109 126 146

 64b-8t4c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1. 13.08      14.44 
2. 13.68 15.10

3. 24 32 39 23 30 36
4. 41 56 73 39 52 70
5. 79 164 258 78 164 253

 1518b-2t1c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  1.47      18.78 
2. 1.48 18.88

3. 94 205 261 83 208 314
4. 72 107 178 100 184 256
5. 151 195 1701 155 193 1549

 1518b-4t2c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  2.73      34.77 
2. 2.77 35.29

3. 77 189 311 57 176 281
4. 78 117 151 75 118 150
5. 135 160 1579 141 166 1604

 imix-2t1c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  2.89       9.88 
2. 3.03 10.39

 imix-4t2c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  5.54      18.95 
2. 5.79 19.83

 imix-8t4c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  8.43      28.87 
2. 8.69 29.75

25ge2p1xxv710-avf-ethip4ipsec10000tnlsw-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.32       4.77 
2. 4.43 4.89

3. 77 180 270 91 202 300
4. 62 87 101 96 127 151
5. 131 168 199 132 174 199

 64b-4t2c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  7.81       8.62 
2. 7.89 8.71

3. 42 119 166 109 220 319
4. 48 62 74 55 75 92
5. 102 119 134 97 113 131

 64b-8t4c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1. 12.52      13.83 
2. 13.10 14.46

3. 22 31 40 20 33 40
4. 40 55 73 40 55 69
5. 76 144 220 75 142 217

 1518b-2t1c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.23      15.69 
2. 1.25 15.93

3. 95 212 316 81 182 285
4. 154 258 342 142 211 322
5. 159 238 2087 163 232 2167

 1518b-4t2c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  2.31      29.45 
2. 2.32 29.60

3. 88 203 317 71 176 290
4. 76 95 125 77 111 160
5. 146 173 330 145 172 355

 imix-2t1c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  2.59       8.85 
2. 2.67 9.12

 imix-4t2c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  5.11      17.49 
2. 5.32 18.20

 imix-8t4c-avf-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  7.90      27.05 
2. 8.27 28.30

25ge2p1xxv710-avf-ethip4ipsec1000tnlsw-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  2.59       3.35 
2. 2.61 3.39

3. 76 190 310 50 173 279
4. 106 171 205 102 174 232
5. 200 252 297 160 199 237

 1518b-2t1c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  0.71       9.20 
2. 0.71 9.20

3. 134 268 388 147 256 349
4. 235 367 435 205 313 433
5. 387 539 616 375 487 585

 imix-2t1c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  1.65       5.97 
2. 1.67 6.03

25ge2p1xxv710-avf-ethip4ipsec1000tnlsw-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.76       5.26 
2. 4.81 5.31

3. 76 185 256 82 210 306
4. 63 86 112 57 75 102
5. 115 136 164 117 139 163

 64b-4t2c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  9.70      10.70 
2. 9.79 10.81

3. 58 113 131 52 124 176
4. 42 55 67 42 56 69
5. 113 130 142 111 127 141

 64b-8t4c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1. 17.68      19.51 
2. 18.12 20.01

3. 24 34 43 21 32 39
4. 45 56 70 44 56 68
5. 81 158 210 79 156 209

 1518b-2t1c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  1.61      20.48 
2. 1.62 20.58

3. 91 207 314 109 224 322
4. 90 145 162 95 134 152
5. 170 220 265 158 206 230

 1518b-4t2c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.17      40.36 
2. 3.18 40.56

3. 71 191 304 80 181 286
4. 72 104 119 74 98 117
5. 173 199 222 168 194 214

 imix-2t1c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.38      11.58 
2. 3.38 11.58

 imix-4t2c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  6.78      23.22 
2. 6.85 23.45

 imix-8t4c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1. 11.52      39.42 
2. 11.63 39.81

25ge2p1xxv710-avf-ethip4ipsec1000tnlsw-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.64       5.13 
2. 4.69 5.18

3. 100 203 289 66 183 267
4. 98 114 132 52 63 72
5. 123 153 174 112 132 152

 64b-4t2c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  9.38      10.36 
2. 9.52 10.51

3. 52 134 167 44 123 150
4. 48 60 67 48 62 85
5. 115 133 147 114 131 145

 64b-8t4c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1. 17.21      19.00 
2. 17.65 19.48

3. 23 34 42 24 34 42
4. 45 56 67 44 54 66
5. 81 160 217 80 158 214

 1518b-2t1c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.32      16.84 
2. 1.32 16.84

3. 102 202 292 98 215 314
4. 100 167 232 102 205 304
5. 155 207 248 159 200 238

 1518b-4t2c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  2.62      33.33 
2. 2.63 33.50

3. 96 200 302 77 204 299
4. 89 139 170 74 113 146
5. 181 210 239 168 194 219

 imix-2t1c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.04      10.40 
2. 3.06 10.46

 imix-4t2c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  6.16      21.09 
2. 6.22 21.30

 imix-8t4c-avf-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1. 10.43      35.71 
2. 10.59 36.25

25ge2p1xxv710-avf-ethip4ipsec1000tnlsw-ip4base-policy-aes256gcm-ndrpdr

IPv4 IPsec tunnel mode performance test suite.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec1000tnlsw- 
ip4base-policy-aes256gcm-ndrpdr

 1.  0.82       0.91 
2. 0.83 0.92

3. 109 204 304 121 223 322
4. 100 200 296 116 226 311
5. 261 377 487 279 389 503

 1518b-2t1c-avf-ethip4ipsec1000tnlsw- 
ip4base-policy-aes256gcm-ndrpdr

 1.  0.57       7.31 
2. 0.57 7.31

3. 124 220 314 130 236 316
4. 161 320 415 191 331 434
5. 312 481 612 327 536 696

 imix-2t1c-avf-ethip4ipsec1000tnlsw- 
ip4base-policy-aes256gcm-ndrpdr

 1.  0.75       2.57 
2. 0.75 2.57

25ge2p1xxv710-avf-ethip4ipsec1tnlsw-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  3.11       4.02 
2. 3.14 4.07

3. 97 180 268 97 173 257
4. 82 117 139 127 174 212
5. 171 218 257 145 172 197

 1518b-2t1c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  0.78      10.07 
2. 0.78 10.07

3. 109 203 326 112 196 294
4. 157 232 259 191 292 338
5. 372 481 568 337 434 525

 imix-2t1c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  1.91       6.90 
2. 1.92 6.94

25ge2p1xxv710-avf-ethip4ipsec1tnlsw-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  6.04       6.67 
2. 6.78 7.48

3. 72 165 245 107 205 271
4. 61 88 106 53 73 85
5. 84 97 109 94 117 132

 64b-4t2c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  6.09       6.72 
2. 6.83 7.54

3. 61 124 152 70 158 242
4. 49 65 87 48 60 71
5. 81 93 103 87 101 113

 64b-8t4c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  6.74       7.44 
2. 6.81 7.52

3. 20 25 36 19 28 59
4. 33 57 69 42 60 68
5. 92 106 124 90 106 123

 1518b-2t1c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  1.90      24.14 
2. 1.91 24.27

3. 108 209 289 99 199 279
4. 81 120 151 83 124 144
5. 157 195 220 140 167 209

 1518b-4t2c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  2.04      26.00 
2. 2.04 26.00

3. 129 223 300 107 189 248
4. 90 157 200 116 186 230
5. 146 187 207 153 205 224

 imix-2t1c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.40      15.07 
2. 4.47 15.29

 imix-4t2c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.50      15.41 
2. 4.59 15.72

 imix-8t4c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.56      15.61 
2. 4.58 15.69

25ge2p1xxv710-avf-ethip4ipsec1tnlsw-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  6.03       6.66 
2. 6.80 7.51

3. 63 130 182 91 168 257
4. 50 67 79 50 68 80
5. 90 109 127 85 98 109

 64b-4t2c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  6.31       6.97 
2. 6.94 7.66

3. 62 128 217 77 169 249
4. 48 64 77 56 71 82
5. 92 106 120 89 104 117

 64b-8t4c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  6.79       7.49 
2. 6.89 7.61

3. 20 30 42 19 29 58
4. 39 50 61 45 70 79
5. 89 103 114 91 108 120

 1518b-2t1c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.47      18.72 
2. 1.48 18.81

3. 119 209 286 133 225 285
4. 76 110 139 118 176 243
5. 182 213 239 218 289 317

 1518b-4t2c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.79      22.86 
2. 1.81 23.09

3. 127 224 293 115 196 276
4. 84 119 145 107 190 209
5. 168 201 231 177 224 247

 imix-2t1c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.93      13.45 
2. 3.99 13.65

 imix-4t2c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.23      14.48 
2. 4.27 14.62

 imix-8t4c-avf-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.21      14.43 
2. 4.26 14.57

25ge2p1xxv710-avf-ethip4ipsec1tnlsw-ip4base-policy-aes256gcm-ndrpdr

IPv4 IPsec tunnel mode performance test suite.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec1tnlsw- 
ip4base-policy-aes256gcm-ndrpdr

 1.  5.36       5.91 
2. 5.69 6.28

3. 60 156 187 88 180 268
4. 75 107 136 66 84 103
5. 94 110 122 100 122 137

 1518b-2t1c-avf-ethip4ipsec1tnlsw- 
ip4base-policy-aes256gcm-ndrpdr

 1.  1.47      18.75 
2. 1.48 18.85

3. 100 206 290 91 181 275
4. 74 147 190 89 178 220
5. 231 302 333 168 237 299

 imix-2t1c-avf-ethip4ipsec1tnlsw- 
ip4base-policy-aes256gcm-ndrpdr

 1.  3.52      12.04 
2. 3.55 12.16

25ge2p1xxv710-avf-ethip4ipsec1tnlswasync-scheduler-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-avf-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  4.04       5.23 
2. 4.06 5.26

3. 76 192 308 72 182 304
4. 77 105 123 75 101 121
5. 120 148 179 116 141 169

 64b-2t4c-avf-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  5.85       7.58 
2. 6.06 7.85

3. 111 226 337 81 111 199
4. 81 110 128 80 102 135
5. 192 222 248 184 211 238

 imix-2t4c-avf-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  5.04      18.23 
2. 5.22 18.88

25ge2p1xxv710-avf-ethip4ipsec1tnlswasync-scheduler-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-avf-ethip4ipsec1tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  5.87       6.48 
2. 6.49 7.17

3. 73 196 300 92 191 268
4. 63 80 94 77 109 137
5. 155 173 187 155 173 185

 64b-2t4c-avf-ethip4ipsec1tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  5.55       6.13 
2. 6.42 7.09

3. 97 191 224 69 142 184
4. 73 96 125 60 75 87
5. 157 179 196 152 170 185

 imix-2t2c-avf-ethip4ipsec1tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  4.86      16.62 
2. 4.90 16.79

 imix-2t4c-avf-ethip4ipsec1tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  5.37      18.39 
2. 5.59 19.15

25ge2p1xxv710-avf-ethip4ipsec1tnlswasync-scheduler-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-avf-ethip4ipsec1tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  5.61       6.20 
2. 6.43 7.09

3. 79 166 223 91 181 259
4. 71 86 99 71 99 119
5. 158 179 199 148 172 187

 64b-2t4c-avf-ethip4ipsec1tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  5.88       6.49 
2. 6.43 7.10

3. 71 113 202 81 143 165
4. 65 84 97 68 86 100
5. 153 170 184 155 171 184

 imix-2t2c-avf-ethip4ipsec1tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  4.83      16.52 
2. 4.87 16.68

 imix-2t4c-avf-ethip4ipsec1tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  5.42      18.56 
2. 5.59 19.12

25ge2p1xxv710-avf-ethip4ipsec2tnlswasync-scheduler-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-avf-ethip4ipsec2tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  3.99       5.17 
2. 4.03 5.22

3. 78 210 338 125 258 382
4. 101 156 211 95 168 220
5. 156 193 227 124 175 210

 64b-2t4c-avf-ethip4ipsec2tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  4.35       5.64 
2. 4.40 5.70

3. 90 240 345 98 251 394
4. 87 137 179 107 167 207
5. 218 256 288 149 251 292

 imix-2t4c-avf-ethip4ipsec2tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  3.89      14.06 
2. 3.95 14.27

25ge2p1xxv710-avf-ethip4ipsec2tnlswasync-scheduler-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-avf-ethip4ipsec2tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  4.58       5.06 
2. 4.61 5.08

3. 85 231 336 102 242 392
4. 71 110 132 109 153 164
5. 209 243 274 131 198 250

 64b-2t4c-avf-ethip4ipsec2tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  4.51       4.98 
2. 4.56 5.03

3. 73 243 320 96 202 280
4. 72 108 122 108 134 153
5. 225 261 286 124 193 224

 imix-2t2c-avf-ethip4ipsec2tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  3.78      12.93 
2. 3.83 13.12

 imix-2t4c-avf-ethip4ipsec2tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  4.04      13.84 
2. 4.10 14.05

25ge2p1xxv710-avf-ethip4ipsec2tnlswasync-scheduler-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-avf-ethip4ipsec2tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  4.58       5.06 
2. 4.63 5.11

3. 101 255 372 113 248 417
4. 63 85 98 68 130 166
5. 237 273 299 134 209 248

 64b-2t4c-avf-ethip4ipsec2tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  4.51       4.98 
2. 4.56 5.03

3. 71 189 258 98 241 358
4. 65 120 149 70 101 114
5. 223 255 281 120 200 232

 imix-2t2c-avf-ethip4ipsec2tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  3.79      12.98 
2. 3.85 13.17

 imix-2t4c-avf-ethip4ipsec2tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  4.03      13.81 
2. 4.12 14.09

25ge2p1xxv710-avf-ethip4ipsec40tnlsw-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  2.71       3.51 
2. 2.75 3.57

3. 88 188 297 88 197 287
4. 86 126 155 93 151 208
5. 200 276 315 172 248 288

 1518b-2t1c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  0.71       9.23 
2. 0.72 9.32

3. 119 221 329 104 214 330
4. 165 261 337 167 273 358
5. 349 474 557 327 454 553

 imix-2t1c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  1.67       6.03 
2. 1.68 6.09

25ge2p1xxv710-avf-ethip4ipsec40tnlsw-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  5.54       6.11 
2. 5.71 6.30

3. 62 153 187 76 176 245
4. 49 63 73 48 67 87
5. 127 166 185 112 152 175

 64b-4t2c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1. 10.86      11.99 
2. 10.97 12.11

3. 55 145 209 42 85 129
4. 47 63 76 45 61 73
5. 106 134 150 99 130 145

 64b-8t4c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1. 19.51      21.54 
2. 20.11 22.20

3. 24 35 43 25 34 41
4. 48 62 74 48 59 70
5. 100 186 230 102 179 222

 1518b-2t1c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  1.69      21.56 
2. 1.71 21.77

3. 106 221 311 90 186 291
4. 84 141 204 85 167 219
5. 158 205 228 147 202 222

 1518b-4t2c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.20      40.81 
2. 3.22 41.02

3. 95 199 308 85 192 307
4. 75 129 148 66 93 114
5. 156 202 230 136 180 207

 imix-2t1c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.65      12.51 
2. 3.71 12.70

 imix-4t2c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  6.95      23.80 
2. 6.99 23.92

 imix-8t4c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1. 12.45      42.61 
2. 12.70 43.48

25ge2p1xxv710-avf-ethip4ipsec40tnlsw-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  5.50       6.07 
2. 5.67 6.26

3. 86 186 278 93 207 309
4. 58 79 112 69 110 135
5. 129 168 186 115 150 176

 64b-4t2c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1. 10.66      11.77 
2. 10.77 11.89

3. 56 103 128 58 133 171
4. 46 58 69 45 57 66
5. 103 130 146 97 127 143

 64b-8t4c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1. 19.56      21.59 
2. 20.06 22.14

3. 24 34 42 24 33 40
4. 47 60 71 47 59 70
5. 101 185 226 101 180 222

 1518b-2t1c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.37      17.45 
2. 1.38 17.63

3. 106 216 328 102 198 286
4. 101 169 224 91 160 190
5. 207 289 319 173 243 275

 1518b-4t2c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  2.58      32.89 
2. 2.60 33.06

3. 64 166 277 40 166 268
4. 73 116 148 70 122 156
5. 138 169 193 122 157 179

 imix-2t1c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.32      11.37 
2. 3.39 11.60

 imix-4t2c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  6.31      21.60 
2. 6.34 21.71

 imix-8t4c-avf-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1. 11.39      39.00 
2. 11.51 39.39

25ge2p1xxv710-avf-ethip4ipsec4tnlsw-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  2.14       2.77 
2. 2.16 2.80

3. 99 182 280 47 187 310
4. 125 211 284 127 230 279
5. 175 240 296 137 218 331

 1518b-2t1c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  0.59       7.61 
2. 0.59 7.64

3. 123 250 341 144 251 383
4. 168 363 413 162 346 450
5. 376 538 645 281 516 626

 imix-2t1c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  1.30       4.71 
2. 1.32 4.76

25ge2p1xxv710-avf-ethip4ipsec4tnlsw-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.49       4.95 
2. 4.58 5.05

3. 69 197 278 92 203 305
4. 49 116 134 59 107 125
5. 124 160 178 94 137 164

 64b-4t2c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  5.28       5.83 
2. 5.33 5.88

3. 75 191 285 73 208 311
4. 60 111 139 69 120 143
5. 105 130 160 61 119 143

 64b-8t4c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  8.78       9.69 
2. 8.91 9.84

3. 21 32 46 20 30 39
4. 35 49 59 33 48 71
5. 81 121 140 39 136 162

 1518b-2t1c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  1.34      17.09 
2. 1.35 17.18

3. 88 182 277 96 216 320
4. 88 178 257 108 226 331
5. 183 249 319 137 219 286

 1518b-4t2c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  1.60      20.33 
2. 1.60 20.33

3. 76 159 256 25 155 267
4. 100 197 269 121 235 333
5. 158 222 285 118 213 286

 imix-2t1c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  2.94      10.07 
2. 2.97 10.17

 imix-4t2c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.52      12.05 
2. 3.54 12.11

 imix-8t4c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  5.63      19.27 
2. 5.74 19.66

25ge2p1xxv710-avf-ethip4ipsec4tnlsw-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.49       4.95 
2. 4.53 5.00

3. 91 186 286 103 199 292
4. 66 124 181 61 90 104
5. 127 159 181 96 140 166

 64b-4t2c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  5.28       5.83 
2. 5.36 5.91

3. 71 182 272 70 204 304
4. 57 104 139 74 114 139
5. 109 137 155 66 118 149

 64b-8t4c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  8.87       9.79 
2. 9.00 9.94

3. 21 31 44 20 30 41
4. 32 47 62 30 45 56
5. 83 121 140 40 136 162

 1518b-2t1c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.12      14.28 
2. 1.13 14.35

3. 88 194 293 75 191 302
4. 102 196 273 140 237 338
5. 165 251 319 140 223 310

 1518b-4t2c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.36      17.33 
2. 1.37 17.50

3. 71 167 265 25 171 294
4. 109 207 281 120 233 328
5. 168 264 328 133 225 292

 imix-2t1c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  2.69       9.21 
2. 2.73 9.33

 imix-4t2c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.22      11.01 
2. 3.27 11.18

 imix-8t4c-avf-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  5.21      17.83 
2. 5.26 18.01

25ge2p1xxv710-avf-ethip4ipsec4tnlswasync-scheduler-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-avf-ethip4ipsec4tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  4.00       5.18 
2. 4.06 5.26

3. 71 230 359 125 259 373
4. 83 136 176 91 157 185
5. 161 204 237 131 185 223

 64b-2t4c-avf-ethip4ipsec4tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  4.32       5.60 
2. 4.37 5.66

3. 75 194 312 112 243 349
4. 85 134 178 77 150 205
5. 219 256 291 168 256 301

 imix-2t4c-avf-ethip4ipsec4tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  3.93      14.22 
2. 3.99 14.44

25ge2p1xxv710-avf-ethip4ipsec4tnlswasync-scheduler-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-avf-ethip4ipsec4tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  4.52       4.99 
2. 4.57 5.04

3. 67 239 326 106 253 387
4. 65 98 114 71 89 105
5. 197 228 252 129 208 246

 64b-2t4c-avf-ethip4ipsec4tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  4.46       4.93 
2. 4.53 5.00

3. 86 208 308 76 242 384
4. 73 96 115 127 158 179
5. 242 276 300 121 211 243

 imix-2t2c-avf-ethip4ipsec4tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  3.79      12.96 
2. 3.84 13.15

 imix-2t4c-avf-ethip4ipsec4tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  4.00      13.70 
2. 4.04 13.84

25ge2p1xxv710-avf-ethip4ipsec4tnlswasync-scheduler-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-avf-ethip4ipsec4tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  4.52       4.99 
2. 4.61 5.09

3. 85 230 344 101 247 392
4. 65 133 152 99 121 137
5. 234 271 295 120 208 253

 64b-2t4c-avf-ethip4ipsec4tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  4.37       4.82 
2. 4.53 5.00

3. 66 218 328 109 244 356
4. 70 127 158 92 158 181
5. 236 272 298 136 209 244

 imix-2t2c-avf-ethip4ipsec4tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  3.78      12.95 
2. 3.84 13.14

 imix-2t4c-avf-ethip4ipsec4tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  4.00      13.70 
2. 4.06 13.91

25ge2p1xxv710-avf-ethip4ipsec8tnlswasync-scheduler-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-avf-ethip4ipsec8tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  3.80       4.93 
2. 3.88 5.03

3. 66 157 301 92 219 349
4. 73 95 119 74 118 149
5. 155 181 211 117 161 197

 64b-2t4c-avf-ethip4ipsec8tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  4.24       5.49 
2. 4.30 5.58

3. 74 211 336 68 163 314
4. 79 106 131 74 99 120
5. 200 223 243 113 226 250

 imix-2t4c-avf-ethip4ipsec8tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  3.81      13.77 
2. 3.85 13.91

25ge2p1xxv710-avf-ethip4ipsec8tnlswasync-scheduler-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-avf-ethip4ipsec8tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  4.49       4.96 
2. 4.54 5.01

3. 74 214 354 77 186 290
4. 57 73 89 83 95 107
5. 226 262 290 130 209 254

 64b-2t4c-avf-ethip4ipsec8tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  4.41       4.87 
2. 4.48 4.94

3. 76 160 283 92 203 366
4. 57 74 91 85 113 141
5. 234 262 283 105 205 231

 imix-2t2c-avf-ethip4ipsec8tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  3.74      12.80 
2. 3.80 12.99

 imix-2t4c-avf-ethip4ipsec8tnlswasync- 
scheduler-ip4base-int-aes128gcm-ndrpdr

 1.  3.91      13.37 
2. 3.97 13.57

25ge2p1xxv710-avf-ethip4ipsec8tnlswasync-scheduler-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-avf-ethip4ipsec8tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  4.48       4.95 
2. 4.53 5.00

3. 66 165 294 78 174 354
4. 81 93 102 64 91 116
5. 206 233 255 105 186 218

 64b-2t4c-avf-ethip4ipsec8tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  4.38       4.84 
2. 4.45 4.91

3. 68 168 208 80 192 300
4. 60 86 103 73 99 119
5. 204 233 257 117 194 236

 imix-2t2c-avf-ethip4ipsec8tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  3.73      12.75 
2. 3.78 12.94

 imix-2t4c-avf-ethip4ipsec8tnlswasync- 
scheduler-ip4base-int-aes256gcm-ndrpdr

 1.  3.90      13.35 
2. 3.98 13.62

25ge2p1xxv710-ethip4ipsec10000tnlsw-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  2.37       3.08 
2. 2.40 3.11

3. 23 54 70 23 49 66
4. 95 119 154 79 165 193
5. 179 228 886 183 244 1156

 1518b-2t1c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  0.67       8.64 
2. 0.67 8.64

3. 45 88 118 46 106 130
4. 157 235 278 141 236 303
5. 383 477 594 386 469 571

 imix-2t1c-ethip4ipsec10000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  1.44       5.19 
2. 1.46 5.27

25ge2p1xxv710-ethip4ipsec10000tnlsw-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.91       4.32 
2. 3.99 4.40

3. 20 38 55 20 34 51
4. 53 88 114 56 88 101
5. 118 147 192 118 148 190

 64b-4t2c-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  7.40       8.17 
2. 7.48 8.26

3. 24 48 74 24 50 78
4. 47 63 77 49 66 77
5. 112 132 158 114 135 160

 64b-8t4c-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1. 13.51      14.91 
2. 13.58 14.99

3. 29 53 73 31 53 79
4. 44 56 69 43 54 65
5. 116 134 150 115 133 148

 1518b-2t1c-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  1.29      16.41 
2. 1.32 16.83

3. 25 51 79 25 67 87
4. 51 115 135 50 103 123
5. 208 294 715 179 245 655

 1518b-4t2c-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  2.37      30.23 
2. 2.37 30.23

3. 25 44 84 25 50 80
4. 60 85 94 54 79 90
5. 135 169 205 140 171 202

 imix-2t1c-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  2.47       8.45 
2. 2.58 8.83

 imix-4t2c-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.72      16.16 
2. 4.72 16.16

 imix-8t4c-ethip4ipsec10000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  8.58      29.36 
2. 8.62 29.50

25ge2p1xxv710-ethip4ipsec10000tnlsw-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.88       4.28 
2. 3.93 4.34

3. 20 32 69 19 28 42
4. 48 94 118 66 94 121
5. 121 158 192 115 154 180

 64b-4t2c-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  6.79       7.50 
2. 6.93 7.65

3. 26 51 79 27 52 65
4. 48 64 76 49 65 77
5. 115 136 160 112 133 156

 64b-8t4c-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1. 12.93      14.27 
2. 13.19 14.56

3. 32 55 74 24 49 76
4. 44 59 70 46 61 72
5. 115 134 157 114 133 153

 1518b-2t1c-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.10      14.06 
2. 1.12 14.20

3. 26 41 67 25 53 86
4. 56 127 151 47 175 210
5. 206 295 355 213 307 349

 1518b-4t2c-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  2.07      26.32 
2. 2.07 26.32

3. 26 62 84 26 54 80
4. 63 85 106 59 86 105
5. 163 212 244 153 187 222

 imix-2t1c-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  2.34       8.00 
2. 2.41 8.24

 imix-4t2c-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.32      14.79 
2. 4.32 14.79

 imix-8t4c-ethip4ipsec10000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  8.11      27.75 
2. 8.11 27.75

25ge2p1xxv710-ethip4ipsec1000tnlsw-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  2.53       3.28 
2. 2.53 3.28

3. 23 33 65 23 46 65
4. 60 99 130 71 90 109
5. 183 223 253 206 236 257

 1518b-2t1c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  0.70       9.05 
2. 0.70 9.05

3. 44 109 144 43 84 134
4. 154 387 486 168 304 396
5. 459 604 689 466 612 725

 imix-2t1c-ethip4ipsec1000tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  1.59       5.75 
2. 1.59 5.75

25ge2p1xxv710-ethip4ipsec1000tnlsw-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.42       4.88 
2. 4.42 4.88

3. 19 42 73 19 34 60
4. 59 76 88 59 74 85
5. 118 149 178 114 147 172

 64b-4t2c-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  8.97       9.90 
2. 8.97 9.90

3. 28 51 79 26 55 77
4. 41 54 66 46 55 62
5. 119 140 158 119 139 157

 64b-8t4c-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1. 18.14      20.02 
2. 18.14 20.02

3. 36 56 71 27 51 79
4. 45 54 62 47 58 67
5. 124 143 159 120 138 154

 1518b-2t1c-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  1.51      19.25 
2. 1.53 19.45

3. 25 44 58 25 74 92
4. 42 120 139 52 84 113
5. 206 275 303 193 243 272

 1518b-4t2c-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  2.82      35.92 
2. 2.82 35.92

3. 25 44 68 25 51 82
4. 61 99 118 60 78 96
5. 178 206 227 156 180 201

 imix-2t1c-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.05      10.45 
2. 3.05 10.45

 imix-4t2c-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  5.94      20.34 
2. 5.94 20.34

 imix-8t4c-ethip4ipsec1000tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1. 11.62      39.79 
2. 11.62 39.79

25ge2p1xxv710-ethip4ipsec1000tnlsw-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.33       4.78 
2. 4.33 4.78

3. 20 48 60 19 40 70
4. 54 73 87 59 83 101
5. 120 149 175 116 146 168

 64b-4t2c-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  8.63       9.53 
2. 8.67 9.58

3. 28 53 76 29 52 76
4. 46 62 74 51 66 78
5. 116 135 152 114 134 152

 64b-8t4c-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1. 17.68      19.52 
2. 17.68 19.52

3. 36 59 78 38 56 73
4. 45 54 62 46 55 62
5. 120 138 154 120 138 154

 1518b-2t1c-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.27      16.12 
2. 1.27 16.12

3. 25 52 66 25 60 84
4. 77 145 187 82 138 158
5. 221 268 303 222 277 312

 1518b-4t2c-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  2.43      30.99 
2. 2.43 30.99

3. 25 52 75 25 48 67
4. 59 79 94 60 84 105
5. 186 216 242 172 208 237

 imix-2t1c-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  2.79       9.54 
2. 2.80 9.59

 imix-4t2c-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  5.55      18.99 
2. 5.55 18.99

 imix-8t4c-ethip4ipsec1000tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1. 10.88      37.23 
2. 10.88 37.23

25ge2p1xxv710-ethip4ipsec1000tnlsw-ip4base-policy-aes256gcm-ndrpdr

IPv4 IPsec tunnel mode performance test suite.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec1000tnlsw- 
ip4base-policy-aes256gcm-ndrpdr

 1.  0.84       0.93 
2. 0.84 0.93

3. 25 62 92 24 54 137
4. 96 290 450 88 363 604
5. 433 729 1023 453 698 911

 1518b-2t1c-ethip4ipsec1000tnlsw- 
ip4base-policy-aes256gcm-ndrpdr

 1.  0.60       7.62 
2. 0.60 7.69

3. 30 61 93 31 60 78
4. 95 250 391 73 295 440
5. 453 869 1072 458 825 993

 imix-2t1c-ethip4ipsec1000tnlsw- 
ip4base-policy-aes256gcm-ndrpdr

 1.  0.76       2.62 
2. 0.76 2.62

25ge2p1xxv710-ethip4ipsec1tnlsw-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec1tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  2.99       3.88 
2. 3.01 3.90

3. 23 50 59 23 89 128
4. 57 118 132 76 138 158
5. 168 202 235 152 199 234

 1518b-2t1c-ethip4ipsec1tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  0.76       9.85 
2. 0.77 9.90

3. 45 67 83 48 92 115
4. 130 336 395 138 283 326
5. 377 482 548 439 565 632

 imix-2t1c-ethip4ipsec1tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  1.82       6.58 
2. 1.83 6.62

25ge2p1xxv710-ethip4ipsec1tnlsw-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  6.12       6.75 
2. 6.15 6.79

3. 20 59 75 19 48 75
4. 41 60 72 50 68 78
5. 95 113 130 92 111 130

 64b-4t2c-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  6.46       7.14 
2. 6.50 7.17

3. 19 50 70 19 54 69
4. 48 70 81 41 56 69
5. 91 111 129 90 106 122

 64b-8t4c-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  6.35       7.01 
2. 6.41 7.08

3. 29 57 78 27 49 68
4. 47 67 78 42 56 68
5. 87 103 118 86 100 111

 1518b-2t1c-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  1.79      22.76 
2. 1.80 22.87

3. 24 47 66 24 41 64
4. 70 103 120 80 125 146
5. 159 205 230 158 196 216

 1518b-4t2c-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  2.00      25.45 
2. 2.00 25.45

3. 24 66 81 24 64 76
4. 78 141 162 60 88 107
5. 115 149 169 124 152 174

 imix-2t1c-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.93      13.45 
2. 3.95 13.52

 imix-4t2c-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.22      14.45 
2. 4.24 14.52

 imix-8t4c-ethip4ipsec1tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.20      14.38 
2. 4.22 14.46

25ge2p1xxv710-ethip4ipsec1tnlsw-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  6.13       6.77 
2. 6.16 6.80

3. 29 59 77 33 60 77
4. 58 82 90 48 69 78
5. 99 121 142 88 105 121

 64b-4t2c-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  6.51       7.19 
2. 6.58 7.26

3. 34 53 80 35 57 79
4. 47 64 74 48 64 74
5. 93 109 123 96 114 131

 64b-8t4c-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  6.50       7.18 
2. 6.54 7.22

3. 19 42 66 33 60 73
4. 49 70 81 50 67 78
5. 87 101 111 95 112 129

 1518b-2t1c-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.41      17.91 
2. 1.41 17.91

3. 24 50 78 24 25 50
4. 58 119 159 64 116 150
5. 140 178 204 163 244 272

 1518b-4t2c-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.72      21.87 
2. 1.72 21.87

3. 24 48 83 24 60 70
4. 66 158 185 58 141 178
5. 162 199 217 152 195 213

 imix-2t1c-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.56      12.19 
2. 3.58 12.25

 imix-4t2c-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.88      13.28 
2. 3.88 13.28

 imix-8t4c-ethip4ipsec1tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.88      13.29 
2. 3.90 13.36

25ge2p1xxv710-ethip4ipsec1tnlsw-ip4base-policy-aes256gcm-ndrpdr

IPv4 IPsec tunnel mode performance test suite.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec1tnlsw- 
ip4base-policy-aes256gcm-ndrpdr

 1.  5.22       5.76 
2. 5.27 5.82

3. 20 48 64 20 49 68
4. 43 63 73 46 79 91
5. 99 116 134 95 114 134

 1518b-2t1c-ethip4ipsec1tnlsw- 
ip4base-policy-aes256gcm-ndrpdr

 1.  1.40      17.89 
2. 1.41 17.98

3. 25 57 84 25 81 108
4. 51 99 112 132 236 269
5. 185 258 305 186 219 252

 imix-2t1c-ethip4ipsec1tnlsw- 
ip4base-policy-aes256gcm-ndrpdr

 1.  3.18      10.88 
2. 3.20 10.94

25ge2p1xxv710-ethip4ipsec1tnlswasync-scheduler-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  3.95       5.11 
2. 3.99 5.17

3. 26 50 57 25 84 129
4. 70 126 148 81 126 148
5. 137 169 199 137 169 199

 64b-2t4c-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  5.34       6.92 
2. 5.40 6.99

3. 27 57 72 25 86 150
4. 88 129 153 75 108 128
5. 203 239 271 180 208 236

 imix-2t2c-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  0.14       0.50 
2. 0.19 0.70

 imix-2t4c-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  4.64      16.77 
2. 4.69 16.94

25ge2p1xxv710-ethip4ipsec1tnlswasync-scheduler-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  5.72       6.31 
2. 5.80 6.41

3. 39 55 69 25 53 67
4. 60 82 99 63 85 96
5. 160 181 201 155 175 196

 64b-2t4c-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  5.72       6.31 
2. 5.78 6.38

3. 23 68 88 44 61 72
4. 70 96 108 63 85 99
5. 171 196 218 161 184 201

 1518b-2t2c-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  1.77      22.54 
2. 1.82 23.23

3. 27 45 70 27 58 70
4. 69 92 106 65 128 152
5. 165 208 240 154 221 252

 imix-2t2c-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.33      14.81 
2. 4.35 14.89

 imix-2t4c-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.74      16.24 
2. 4.79 16.40

25ge2p1xxv710-ethip4ipsec1tnlswasync-scheduler-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  5.74       6.34 
2. 5.80 6.41

3. 22 61 90 39 85 92
4. 59 86 101 68 94 106
5. 155 177 198 148 169 188

 64b-2t4c-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  5.71       6.30 
2. 5.77 6.37

3. 22 64 89 43 58 83
4. 66 103 113 62 80 90
5. 169 196 218 162 188 207

 1518b-2t2c-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.49      18.93 
2. 1.51 19.22

3. 27 44 63 27 45 60
4. 45 117 135 62 122 139
5. 160 231 267 158 216 256

 imix-2t2c-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.34      14.85 
2. 4.38 15.00

 imix-2t4c-ethip4ipsec1tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.70      16.07 
2. 4.74 16.24

25ge2p1xxv710-ethip4ipsec2tnlswasync-scheduler-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t4c-ethip4ipsec2tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  3.91       5.07 
2. 3.95 5.12

3. 28 49 77 26 54 65
4. 70 102 130 58 91 124
5. 217 251 282 128 249 288

 imix-2t4c-ethip4ipsec2tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  3.36      12.13 
2. 3.37 12.19

25ge2p1xxv710-ethip4ipsec2tnlswasync-scheduler-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-ethip4ipsec2tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.13       4.56 
2. 4.15 4.58

3. 22 47 62 22 31 69
4. 66 105 121 54 101 124
5. 219 253 284 107 204 250

 64b-2t4c-ethip4ipsec2tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.04       4.46 
2. 4.08 4.51

3. 22 46 69 22 54 78
4. 64 92 106 48 80 93
5. 235 273 308 104 217 257

 imix-2t2c-ethip4ipsec2tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.28      11.22 
2. 3.31 11.32

 imix-2t4c-ethip4ipsec2tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.39      11.60 
2. 3.41 11.66

25ge2p1xxv710-ethip4ipsec2tnlswasync-scheduler-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-ethip4ipsec2tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.10       4.53 
2. 4.14 4.57

3. 22 57 67 22 52 91
4. 58 97 112 46 81 96
5. 206 241 269 108 201 248

 64b-2t4c-ethip4ipsec2tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.03       4.45 
2. 4.05 4.47

3. 25 50 79 24 49 62
4. 67 91 111 51 89 113
5. 215 252 285 106 205 257

 imix-2t2c-ethip4ipsec2tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.27      11.20 
2. 3.32 11.36

 imix-2t4c-ethip4ipsec2tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.38      11.56 
2. 3.41 11.68

25ge2p1xxv710-ethip4ipsec40tnlsw-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec40tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  2.58       3.34 
2. 2.60 3.37

3. 23 54 83 23 50 77
4. 68 94 120 57 110 133
5. 195 268 306 184 258 313

 1518b-2t1c-ethip4ipsec40tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  0.69       8.87 
2. 0.69 8.87

3. 47 71 95 52 72 84
4. 132 198 232 130 211 245
5. 368 517 595 361 496 590

 imix-2t1c-ethip4ipsec40tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  1.57       5.67 
2. 1.58 5.70

25ge2p1xxv710-ethip4ipsec40tnlsw-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  5.01       5.53 
2. 5.06 5.59

3. 20 53 82 19 29 40
4. 53 72 83 49 66 79
5. 116 145 172 113 166 183

 64b-4t2c-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  9.87      10.89 
2. 10.02 11.06

3. 40 56 78 30 55 82
4. 46 57 67 47 60 72
5. 110 144 166 103 143 167

 64b-8t4c-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1. 18.64      20.58 
2. 18.92 20.89

3. 30 50 73 33 54 77
4. 47 57 65 46 56 64
5. 109 164 206 109 162 205

 1518b-2t1c-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  1.55      19.70 
2. 1.56 19.89

3. 24 44 79 24 52 69
4. 36 137 153 40 88 118
5. 153 202 247 145 201 240

 1518b-4t2c-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  2.93      37.35 
2. 2.95 37.54

3. 25 56 80 24 45 66
4. 59 79 99 59 82 100
5. 140 175 197 135 176 206

 imix-2t1c-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.19      10.93 
2. 3.21 10.99

 imix-4t2c-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  6.21      21.27 
2. 6.25 21.38

 imix-8t4c-ethip4ipsec40tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1. 11.07      37.89 
2. 11.07 37.89

25ge2p1xxv710-ethip4ipsec40tnlsw-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  5.02       5.54 
2. 5.07 5.60

3. 23 47 72 25 47 75
4. 49 64 82 53 71 84
5. 123 155 186 112 155 184

 64b-4t2c-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  9.79      10.81 
2. 9.94 10.97

3. 24 44 72 22 39 67
4. 45 58 69 43 56 67
5. 109 143 164 101 137 159

 64b-8t4c-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1. 18.53      20.46 
2. 18.72 20.66

3. 32 53 71 29 52 78
4. 48 59 68 45 54 62
5. 107 156 195 106 155 196

 1518b-2t1c-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.28      16.31 
2. 1.29 16.47

3. 25 53 72 25 54 81
4. 52 132 163 66 108 166
5. 178 237 264 132 202 223

 1518b-4t2c-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  2.46      31.27 
2. 2.47 31.43

3. 25 34 60 25 49 72
4. 65 102 129 53 71 88
5. 134 174 205 135 170 203

 imix-2t1c-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  2.97      10.18 
2. 2.99 10.23

 imix-4t2c-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  5.67      19.42 
2. 5.73 19.61

 imix-8t4c-ethip4ipsec40tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1. 10.28      35.18 
2. 10.28 35.18

25ge2p1xxv710-ethip4ipsec4tnlsw-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  2.06       2.67 
2. 2.08 2.69

3. 23 41 65 23 48 79
4. 53 76 92 45 80 113
5. 189 245 283 118 236 284

 1518b-2t1c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  0.58       7.44 
2. 0.58 7.44

3. 45 71 107 46 82 114
4. 114 285 326 80 303 426
5. 330 460 528 239 446 550

 imix-2t1c-ethip4ipsec4tnlsw-ip4base- 
int-aes128cbc-hmac512sha-ndrpdr

 1.  1.25       4.53 
2. 1.27 4.59

25ge2p1xxv710-ethip4ipsec4tnlsw-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.14       4.57 
2. 4.16 4.59

3. 19 44 67 19 29 54
4. 47 74 88 43 66 80
5. 115 142 165 77 144 182

 64b-4t2c-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.87       5.37 
2. 4.92 5.43

3. 20 39 67 19 37 65
4. 39 59 73 33 64 84
5. 99 123 144 50 108 145

 64b-8t4c-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  7.99       8.82 
2. 8.07 8.91

3. 27 51 80 20 50 74
4. 45 64 78 44 67 85
5. 81 123 146 50 124 157

 1518b-2t1c-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  1.27      16.22 
2. 1.27 16.22

3. 24 42 62 24 47 76
4. 50 95 149 44 111 125
5. 153 213 261 120 216 263

 1518b-4t2c-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  1.50      19.13 
2. 1.50 19.13

3. 24 44 61 24 28 42
4. 49 68 81 30 73 109
5. 114 156 184 66 126 175

 imix-2t1c-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  2.61       8.93 
2. 2.62 8.97

 imix-4t2c-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.11      10.64 
2. 3.12 10.69

 imix-8t4c-ethip4ipsec4tnlsw- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.94      16.90 
2. 4.96 16.98

25ge2p1xxv710-ethip4ipsec4tnlsw-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t1c-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.11       4.54 
2. 4.13 4.56

3. 24 52 84 19 42 79
4. 47 68 83 41 69 89
5. 117 145 169 85 140 174

 64b-4t2c-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.91       5.42 
2. 4.93 5.44

3. 19 49 72 19 45 76
4. 38 61 82 31 63 85
5. 100 122 138 50 108 152

 64b-8t4c-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  8.05       8.88 
2. 8.13 8.97

3. 20 49 80 19 44 77
4. 44 63 77 43 64 81
5. 81 124 146 48 124 153

 1518b-2t1c-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.04      13.28 
2. 1.04 13.28

3. 25 42 84 25 41 87
4. 49 150 190 38 94 156
5. 187 272 306 134 244 305

 1518b-4t2c-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  1.27      16.23 
2. 1.28 16.31

3. 25 29 82 24 26 47
4. 48 98 135 28 87 116
5. 153 192 228 72 150 221

 imix-2t1c-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  2.41       8.24 
2. 2.41 8.24

 imix-4t2c-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  2.90       9.93 
2. 2.90 9.93

 imix-8t4c-ethip4ipsec4tnlsw- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.58      15.69 
2. 4.61 15.77

25ge2p1xxv710-ethip4ipsec4tnlswasync-scheduler-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t4c-ethip4ipsec4tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  3.88       5.03 
2. 3.94 5.11

3. 26 49 62 26 60 87
4. 62 92 119 57 86 102
5. 219 252 284 136 247 285

 imix-2t4c-ethip4ipsec4tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  3.33      12.03 
2. 3.36 12.15

25ge2p1xxv710-ethip4ipsec4tnlswasync-scheduler-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-ethip4ipsec4tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.10       4.52 
2. 4.14 4.57

3. 22 45 80 23 53 63
4. 65 99 116 53 88 108
5. 224 259 289 111 204 245

 64b-2t4c-ethip4ipsec4tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.02       4.44 
2. 4.06 4.48

3. 22 42 52 22 56 73
4. 58 80 96 47 78 97
5. 220 256 287 107 206 260

 imix-2t2c-ethip4ipsec4tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.26      11.14 
2. 3.29 11.25

 imix-2t4c-ethip4ipsec4tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.37      11.53 
2. 3.40 11.64

25ge2p1xxv710-ethip4ipsec4tnlswasync-scheduler-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-ethip4ipsec4tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.09       4.52 
2. 4.13 4.56

3. 22 62 73 22 46 64
4. 58 93 108 47 78 89
5. 214 248 279 109 209 254

 64b-2t4c-ethip4ipsec4tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.99       4.40 
2. 4.05 4.47

3. 25 45 64 23 52 67
4. 61 86 100 48 78 96
5. 220 255 283 108 212 257

 imix-2t2c-ethip4ipsec4tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.27      11.19 
2. 3.30 11.30

 imix-2t4c-ethip4ipsec4tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.36      11.50 
2. 3.39 11.62

25ge2p1xxv710-ethip4ipsec8tnlswasync-scheduler-ip4base-int-aes128cbc-hmac512sha-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t4c-ethip4ipsec8tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  3.84       4.98 
2. 3.88 5.03

3. 28 45 61 28 61 85
4. 75 100 120 66 92 112
5. 228 262 299 113 251 288

 imix-2t4c-ethip4ipsec8tnlswasync-scheduler- 
ip4base-int-aes128cbc-hmac512sha-ndrpdr

 1.  3.30      11.93 
2. 3.33 12.05

25ge2p1xxv710-ethip4ipsec8tnlswasync-scheduler-ip4base-int-aes128gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-ethip4ipsec8tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  4.06       4.48 
2. 4.10 4.53

3. 28 57 73 23 49 64
4. 68 99 115 51 93 119
5. 231 268 301 110 214 254

 64b-2t4c-ethip4ipsec8tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.96       4.38 
2. 4.00 4.42

3. 30 42 52 22 54 73
4. 64 87 104 46 77 91
5. 220 252 281 105 209 251

 imix-2t2c-ethip4ipsec8tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.21      11.00 
2. 3.25 11.11

 imix-2t4c-ethip4ipsec8tnlswasync-scheduler- 
ip4base-int-aes128gcm-ndrpdr

 1.  3.29      11.24 
2. 3.34 11.41

25ge2p1xxv710-ethip4ipsec8tnlswasync-scheduler-ip4base-int-aes256gcm-ndrpdr

RFC2544: Pkt throughput IPv4 IPsec tunnel mode.

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv4 on TG-DUTn, Eth-IPv4-IPSec on DUT1-DUT2

  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with multiple IPsec tunnels between them, run with IPsec async mode and use crypto sw scheduler engine to schedule crypto work to crypto cores. DUTs get IPv4 traffic from TG, encrypt it and send to another DUT, where packets are decrypted and sent back to TG.

  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, number of flows per flow-group equals to number of IPSec tunnels) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC4303 and RFC2544.

 Test Name 

 Throughput: 
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)

One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)

 64b-2t2c-ethip4ipsec8tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  4.04       4.47 
2. 4.09 4.51

3. 27 55 73 31 54 72
4. 65 82 98 58 78 96
5. 217 248 279 109 193 234

 64b-2t4c-ethip4ipsec8tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.93       4.34 
2. 3.99 4.41

3. 22 41 57 22 31 49
4. 67 93 106 49 82 96
5. 219 253 281 104 209 254

 imix-2t2c-ethip4ipsec8tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.23      11.06 
2. 3.26 11.17

 imix-2t4c-ethip4ipsec8tnlswasync-scheduler- 
ip4base-int-aes256gcm-ndrpdr

 1.  3.29      11.28 
2. 3.34 11.45