3n-skx-xxv710
25ge2p1xxv710-avf-dot1q-l2bdbasemaclrn-ndrpdr
RFC2544: Pkt throughput L2BD with IEEE 802.1Q test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge domain and MAC learning enabled. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 17.93 12.62
2. 18.20 12.81
3. 17 26 32 17 28 36
4. 31 39 44 28 37 44
5. 62 70 77 60 69 77
|
64b-4t2c-avf-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 34.19 24.07
2. 35.90 25.28
3. 21 28 35 19 27 34
4. 29 34 37 28 33 36
5. 55 61 65 55 60 65
|
64b-8t4c-avf-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 34.52 24.30
2. 34.95 24.61
3. 22 36 51 26 40 47
4. 25 29 34 24 28 32
5. 31 35 39 30 34 38
|
1518b-2t1c-avf-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 3.89 48.03
2. 3.91 48.27
3. 20 27 34 20 25 35
4. 27 38 46 27 34 40
5. 39 47 52 41 55 62
|
1518b-4t2c-avf-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 3.90 48.06
2. 3.92 48.30
3. 20 21 30 20 21 21
4. 28 36 46 30 44 53
5. 46 55 60 44 55 64
|
9000b-2t1c-avf-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 49 57 35 40 47
4. 46 136 157 51 132 159
5. 99 166 183 108 176 183
|
imix-2t1c-avf-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 16.12 48.72
2. 16.16 48.86
|
imix-4t2c-avf-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 16.13 48.76
2. 16.13 48.76
|
imix-8t4c-avf-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 16.13 48.76
2. 16.13 48.76
|
25ge2p1xxv710-avf-dot1q-l2xcbase-ndrpdr
RFC2544: Pkt throughput L2XC with IEEE 802.1Q test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-
dot1q-l2xcbase-ndrpdr
|
1. 24.85 17.49
2. 25.12 17.69
3. 17 26 33 17 22 28
4. 26 32 37 27 32 36
5. 46 52 59 46 52 59
|
64b-4t2c-avf-
dot1q-l2xcbase-ndrpdr
|
1. 36.94 26.01
2. 37.31 26.27
3. 20 28 34 19 28 36
4. 24 28 31 24 27 31
5. 32 35 38 32 35 38
|
64b-8t4c-avf-
dot1q-l2xcbase-ndrpdr
|
1. 31.93 22.48
2. 32.65 22.98
3. 21 33 44 23 35 46
4. 23 31 33 22 31 34
5. 26 30 33 25 28 31
|
1518b-2t1c-avf-
dot1q-l2xcbase-ndrpdr
|
1. 3.89 48.03
2. 3.91 48.27
3. 20 24 36 19 27 35
4. 27 39 44 27 38 47
5. 40 51 55 41 57 62
|
1518b-4t2c-avf-
dot1q-l2xcbase-ndrpdr
|
1. 3.89 48.02
2. 3.91 48.26
3. 20 26 35 19 28 35
4. 29 38 46 30 40 47
5. 43 64 73 41 50 56
|
9000b-2t1c-avf-
dot1q-l2xcbase-ndrpdr
|
1. 0.66 47.94
2. 0.67 48.18
3. 36 45 53 35 41 50
4. 39 224 250 48 273 289
5. 205 326 341 202 321 331
|
imix-2t1c-avf-
dot1q-l2xcbase-ndrpdr
|
1. 16.15 48.82
2. 16.15 48.82
|
imix-4t2c-avf-
dot1q-l2xcbase-ndrpdr
|
1. 16.13 48.76
2. 16.13 48.76
|
imix-8t4c-avf-
dot1q-l2xcbase-ndrpdr
|
1. 16.13 48.76
2. 16.13 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 8.17 5.49
2. 13.40 9.01
3. 17 28 36 17 26 32
4. 28 34 39 27 34 40
5. 51 59 65 51 59 65
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 18.00 12.10
2. 25.94 17.43
3. 21 29 36 19 27 33
4. 26 31 35 26 31 34
5. 47 57 64 45 51 56
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 30.77 20.68
2. 32.19 21.63
3. 24 35 47 23 36 48
4. 23 26 30 24 28 32
5. 30 34 37 29 33 36
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 29 38 20 33 44
4. 27 39 48 28 37 45
5. 41 50 55 40 51 58
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 21 24 20 29 35
4. 30 44 55 30 42 51
5. 46 59 68 43 58 67
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 39 44 35 76 98
4. 45 197 238 39 269 303
5. 168 274 291 269 361 380
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 11.16 33.36
2. 13.36 39.96
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 14.75 44.10
2. 16.22 48.51
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 7.48 5.03
2. 11.72 7.88
3. 18 27 35 17 27 31
4. 29 36 42 28 35 41
5. 53 62 68 52 62 70
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 15.92 10.70
2. 22.66 15.23
3. 22 28 33 17 18 24
4. 27 31 35 26 31 35
5. 48 55 62 49 57 65
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 30.79 20.69
2. 32.38 21.76
3. 23 37 47 23 35 45
4. 26 30 34 25 29 33
5. 32 36 40 33 37 40
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 3.88 47.76
2. 3.92 48.25
3. 20 36 54 21 34 39
4. 30 50 64 29 42 49
5. 41 52 59 46 55 62
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 3.86 47.44
2. 3.91 48.15
3. 20 22 29 20 21 31
4. 32 43 55 33 50 60
5. 44 58 68 41 61 69
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 0.66 47.31
2. 0.67 48.27
3. 37 41 49 36 52 59
4. 40 146 155 39 179 206
5. 156 255 268 209 287 300
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 8.81 26.36
2. 11.17 33.41
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 14.80 44.28
2. 16.33 48.84
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 7.99 5.37
2. 13.05 8.77
3. 17 27 33 17 27 34
4. 27 34 39 28 34 40
5. 51 59 64 52 60 67
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 17.88 12.01
2. 25.49 17.13
3. 19 28 36 20 28 35
4. 27 31 35 26 31 34
5. 48 54 62 46 52 59
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 31.09 20.89
2. 31.88 21.42
3. 22 34 47 22 35 48
4. 24 28 33 24 28 33
5. 32 37 42 31 36 41
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 21 29 20 21 26
4. 28 36 48 29 44 53
5. 41 51 54 43 53 59
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 29 34 20 33 41
4. 29 45 55 29 47 60
5. 49 62 74 41 53 67
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 51 61 35 42 50
4. 40 101 119 48 138 182
5. 122 187 200 126 175 186
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 10.26 30.70
2. 12.95 38.72
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 14.75 44.10
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 7.54 5.07
2. 10.69 7.19
3. 17 30 37 17 27 35
4. 28 37 42 26 34 40
5. 53 62 70 52 62 70
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 14.25 9.57
2. 18.66 12.54
3. 21 30 37 19 29 35
4. 29 35 41 27 32 38
5. 65 106 150 58 93 141
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 21.83 14.67
2. 24.14 16.22
3. 25 38 50 21 34 43
4. 25 30 34 24 29 34
5. 38 51 69 37 49 61
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 30 35 20 21 21
4. 28 44 52 28 43 52
5. 47 58 67 45 52 58
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 23 31 20 28 36
4. 30 41 51 30 40 50
5. 42 53 60 48 56 64
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 45 50 35 49 57
4. 44 70 115 49 112 166
5. 114 160 164 135 218 233
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 8.66 25.91
2. 10.79 32.25
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 7.38 4.96
2. 10.81 7.26
3. 17 28 36 17 25 33
4. 29 36 41 28 40 48
5. 54 63 69 53 63 72
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 14.55 9.78
2. 16.75 11.25
3. 17 28 35 19 29 35
4. 27 34 40 25 31 36
5. 47 74 105 39 53 68
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 22.77 15.30
2. 25.30 17.00
3. 24 35 47 25 38 49
4. 25 30 35 25 30 35
5. 38 49 62 39 53 69
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 27 37 20 21 31
4. 30 39 48 25 57 70
5. 49 66 74 55 77 88
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 25 33 20 31 37
4. 30 43 53 30 43 53
5. 45 57 63 45 62 72
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 37 41 35 75 81
4. 39 172 184 64 212 226
5. 164 256 271 199 316 332
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 8.76 26.21
2. 10.87 32.52
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 14.53 43.45
2. 16.38 49.00
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 7.69 5.17
2. 10.79 7.25
3. 17 29 36 17 29 36
4. 27 34 40 27 34 40
5. 54 63 71 52 61 70
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 14.24 9.57
2. 17.02 11.44
3. 17 28 35 20 28 34
4. 28 39 46 23 31 35
5. 44 61 79 45 66 89
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 21.01 14.12
2. 22.84 15.35
3. 21 33 37 26 39 54
4. 24 30 35 24 29 34
5. 41 58 80 31 39 48
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 21 27 20 22 35
4. 27 46 55 28 45 54
5. 44 55 70 42 53 61
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 27 34 20 32 45
4. 29 44 53 30 41 54
5. 42 52 61 45 55 63
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 45 57 35 38 41
4. 42 139 153 55 138 157
5. 133 217 245 125 205 220
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 8.44 25.26
2. 10.78 32.24
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 14.75 44.10
2. 16.38 49.00
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 13.09 8.79
2. 13.35 8.97
3. 17 23 36 17 26 38
4. 30 40 48 28 40 47
5. 51 58 63 50 59 65
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 25.20 16.93
2. 25.78 17.33
3. 17 29 35 17 27 34
4. 27 32 36 26 32 35
5. 46 51 56 44 54 61
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 32.16 21.61
2. 32.81 22.05
3. 22 34 44 24 36 48
4. 25 31 35 25 31 36
5. 29 33 36 29 34 38
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 20 28 20 20 30
4. 23 61 71 33 65 73
5. 41 58 61 56 81 87
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 20 24 20 20 28
4. 30 52 60 32 43 53
5. 45 57 65 42 52 60
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 45 53 35 38 41
4. 40 175 183 39 323 339
5. 208 318 327 202 317 325
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 12.83 38.37
2. 13.33 39.86
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 14.75 44.10
2. 16.08 48.09
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 11.23 7.55
2. 11.70 7.86
3. 17 33 36 19 34 42
4. 30 38 44 26 41 48
5. 52 61 68 52 62 70
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 22.00 14.79
2. 22.75 15.29
3. 17 19 27 17 26 31
4. 27 32 36 28 33 39
5. 50 59 66 52 61 69
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 31.23 20.99
2. 31.86 21.41
3. 18 31 39 20 32 47
4. 28 33 37 27 33 37
5. 32 36 40 31 35 39
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 3.90 48.00
2. 3.92 48.24
3. 20 22 25 20 36 47
4. 27 56 71 33 65 74
5. 51 62 67 54 65 71
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 3.89 47.88
2. 3.91 48.12
3. 20 28 39 20 31 42
4. 32 49 60 29 55 68
5. 56 73 81 40 69 74
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 41 48 35 59 68
4. 39 234 246 39 184 237
5. 199 319 335 86 193 206
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 10.64 31.82
2. 11.13 33.29
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 14.77 44.18
2. 15.69 46.92
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 12.80 8.60
2. 13.12 8.82
3. 17 27 32 17 35 43
4. 29 37 42 24 37 46
5. 51 58 64 57 66 73
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 25.20 16.93
2. 25.81 17.34
3. 18 27 33 17 26 33
4. 28 33 36 27 33 37
5. 52 58 64 51 59 65
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 31.06 20.87
2. 32.16 21.61
3. 23 34 46 21 35 47
4. 23 26 30 24 28 32
5. 30 35 39 30 34 38
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 28 36 20 21 30
4. 28 37 43 32 58 74
5. 45 53 59 45 56 67
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 29 37 20 36 49
4. 28 47 60 29 49 59
5. 47 61 72 54 66 75
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 38 39 36 54 60
4. 43 132 165 41 173 190
5. 208 296 312 131 162 187
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 12.60 37.69
2. 12.93 38.66
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 10.59 7.12
2. 10.86 7.30
3. 17 21 33 17 33 45
4. 29 37 42 27 40 47
5. 56 66 74 57 70 78
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 16.52 11.10
2. 17.73 11.91
3. 19 28 35 17 30 36
4. 27 33 38 27 34 39
5. 59 97 141 42 53 63
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 19.49 13.10
2. 21.73 14.60
3. 17 31 38 17 28 39
4. 25 31 36 25 30 35
5. 34 42 50 38 52 71
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 21 27 20 27 31
4. 28 39 50 29 37 44
5. 46 58 63 41 54 60
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 22 24 20 32 38
4. 29 43 54 31 48 58
5. 47 54 58 41 48 55
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 64 78 35 45 55
4. 39 288 326 58 291 306
5. 200 321 335 203 319 325
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 10.60 31.70
2. 10.76 32.17
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 14.75 44.10
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 10.42 7.01
2. 10.58 7.11
3. 17 27 34 17 30 45
4. 27 37 43 28 41 47
5. 53 63 72 54 66 76
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 15.20 10.21
2. 16.00 10.75
3. 21 29 36 17 25 33
4. 27 34 39 26 32 37
5. 38 49 62 36 45 53
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 22.22 14.93
2. 23.36 15.70
3. 20 30 39 17 17 23
4. 27 32 37 25 31 37
5. 36 46 58 37 49 63
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 30 37 20 35 61
4. 23 44 51 25 47 52
5. 54 69 75 41 55 61
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 22 30 20 30 38
4. 27 58 72 34 60 73
5. 57 75 82 57 79 88
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 37 39 35 40 50
4. 38 306 337 60 288 306
5. 186 309 322 265 365 380
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 10.56 31.59
2. 10.83 32.40
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 14.45 43.23
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 10.56 7.09
2. 10.85 7.29
3. 17 32 39 17 33 45
4. 29 40 45 27 44 50
5. 55 65 72 56 67 75
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 15.71 10.56
2. 16.08 10.80
3. 17 27 36 17 21 32
4. 26 32 37 26 31 36
5. 38 49 59 38 51 61
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 21.88 14.71
2. 23.43 15.74
3. 25 40 50 23 37 52
4. 26 32 37 24 30 35
5. 39 54 75 35 45 54
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 30 36 20 28 37
4. 24 42 50 29 45 57
5. 52 68 76 37 43 49
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 31 47 20 26 37
4. 30 45 56 32 54 63
5. 47 65 70 50 61 68
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 45 54 35 77 90
4. 43 141 159 40 235 252
5. 175 218 227 203 322 332
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 10.53 31.48
2. 10.80 32.31
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.38 49.00
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 13.14 8.83
2. 13.32 8.95
3. 17 28 36 17 28 40
4. 28 37 43 26 33 39
5. 51 58 64 48 56 62
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 25.15 16.90
2. 25.92 17.42
3. 18 26 31 17 25 31
4. 27 32 35 27 32 36
5. 47 58 66 45 51 56
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 32.36 21.75
2. 34.19 22.98
3. 21 31 42 23 34 43
4. 24 28 31 24 27 31
5. 31 35 39 31 34 38
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 21 25 20 27 33
4. 31 50 56 27 46 56
5. 52 69 77 54 68 76
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 30 39 20 27 33
4. 30 44 52 27 49 60
5. 49 60 67 48 64 72
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 55 65 35 56 66
4. 39 247 299 38 203 238
5. 200 318 328 159 228 246
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 12.94 38.69
2. 13.38 40.00
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 11.28 7.58
2. 11.68 7.85
3. 18 40 45 18 41 45
4. 32 43 49 30 40 45
5. 54 64 71 55 66 74
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 21.82 14.66
2. 22.38 15.04
3. 17 21 27 17 18 28
4. 27 34 39 27 32 37
5. 47 55 64 49 57 66
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 31.75 21.34
2. 32.56 21.88
3. 22 33 43 22 33 48
4. 26 32 36 26 30 34
5. 32 37 41 34 38 45
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 3.90 47.94
2. 3.92 48.18
3. 20 22 32 20 27 36
4. 24 58 68 26 37 45
5. 48 61 66 46 60 72
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 3.89 47.85
2. 3.91 48.09
3. 20 26 34 20 24 37
4. 29 41 50 29 37 45
5. 49 61 69 41 48 54
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 38 40 35 53 64
4. 39 203 236 49 185 207
5. 197 315 329 163 242 252
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 10.65 31.87
2. 11.15 33.34
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 14.80 44.26
2. 16.34 48.86
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 12.79 8.60
2. 13.12 8.82
3. 17 30 37 17 32 37
4. 28 39 45 28 39 44
5. 53 61 66 51 58 65
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 24.91 16.74
2. 25.29 16.99
3. 21 29 35 18 28 34
4. 26 31 35 26 31 35
5. 44 50 55 47 54 59
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 31.08 20.89
2. 32.03 21.52
3. 25 39 50 24 35 46
4. 24 27 31 24 28 31
5. 29 33 38 30 33 38
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 24 32 20 28 35
4. 25 40 47 27 34 41
5. 44 56 62 41 56 62
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 33 49 20 22 31
4. 31 52 63 31 56 66
5. 55 71 80 47 60 68
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 38 40 35 38 46
4. 39 249 283 41 198 210
5. 183 285 314 116 237 246
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 12.54 37.52
2. 12.96 38.75
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 10.57 7.10
2. 10.70 7.19
3. 17 33 41 17 34 46
4. 27 39 46 29 41 48
5. 54 64 72 53 64 73
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 17.28 11.62
2. 17.93 12.05
3. 17 26 33 17 26 32
4. 27 33 38 27 34 39
5. 42 53 64 43 55 67
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 23.18 15.58
2. 24.75 16.63
3. 22 34 45 17 26 38
4. 26 32 36 24 29 34
5. 40 53 70 35 45 54
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 21 26 20 20 22
4. 28 50 57 30 40 50
5. 49 56 64 40 52 57
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 32 52 20 36 49
4. 24 54 68 26 56 68
5. 56 74 83 44 70 75
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 55 64 35 52 60
4. 39 168 176 44 161 177
5. 165 225 293 173 332 340
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 10.57 31.62
2. 10.84 32.42
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 14.67 43.88
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.38 49.00
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 10.53 7.08
2. 10.69 7.18
3. 17 22 31 17 22 35
4. 27 35 42 26 34 40
5. 53 65 73 54 66 74
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 15.30 10.28
2. 16.10 10.82
3. 17 27 36 17 24 30
4. 25 31 37 26 32 37
5. 38 48 59 40 54 69
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 22.79 15.31
2. 24.08 16.18
3. 27 42 53 26 38 49
4. 26 33 37 25 30 34
5. 36 47 58 39 51 66
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 21 32 38 20 33 49
4. 28 40 51 28 45 54
5. 50 64 69 44 64 70
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 33 39 20 21 28
4. 29 42 49 34 64 78
5. 50 60 68 54 71 79
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 68 79 35 52 59
4. 38 249 303 38 178 201
5. 198 326 345 167 256 283
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 10.53 31.49
2. 10.69 31.97
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 14.53 43.45
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 10.54 7.08
2. 10.75 7.22
3. 17 27 39 17 22 36
4. 26 37 43 26 34 40
5. 56 67 74 53 63 70
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 15.60 10.48
2. 16.35 10.99
3. 18 28 34 17 28 38
4. 26 31 37 26 31 35
5. 41 54 68 39 52 62
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 22.52 15.13
2. 23.91 16.07
3. 23 40 54 17 32 50
4. 26 32 37 25 30 35
5. 40 52 70 35 45 55
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 23 35 20 31 38
4. 28 40 47 28 49 60
5. 41 53 58 42 52 57
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 28 35 20 24 35
4. 29 40 48 31 48 59
5. 51 63 73 45 61 71
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 46 57 35 37 39
4. 40 147 159 49 193 210
5. 100 240 247 199 334 349
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 10.54 31.53
2. 10.76 32.17
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 14.53 43.45
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdr
|
1. 6.34 4.26
2. 6.63 4.46
3. 17 21 30 16 21 36
4. 24 34 40 24 39 47
5. 41 50 57 62 77 92
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdr
|
1. 10.46 7.03
2. 12.17 8.18
3. 17 22 32 17 26 35
4. 28 35 41 27 34 41
5. 83 146 231 52 77 122
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdr
|
1. 16.08 10.81
2. 17.94 12.05
3. 20 32 43 20 33 46
4. 26 33 40 26 32 39
5. 48 78 114 37 48 63
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 25 33 20 25 31
4. 29 41 49 31 42 50
5. 49 69 77 49 63 70
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 28 43 20 21 28
4. 29 41 54 29 35 42
5. 47 55 68 41 48 55
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 38 54 35 37 42
4. 44 173 187 41 161 211
5. 189 292 335 127 230 243
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdr
|
1. 6.33 18.93
2. 6.69 20.01
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdr
|
1. 9.83 29.41
2. 10.99 32.86
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdr
|
1. 13.89 41.53
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdr
|
1. 6.11 4.11
2. 6.31 4.24
3. 17 25 38 17 24 29
4. 26 43 52 25 43 51
5. 58 75 93 47 63 69
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdr
|
1. 10.29 6.92
2. 11.71 7.87
3. 24 32 39 20 30 36
4. 29 37 44 28 38 45
5. 55 85 129 54 81 128
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdr
|
1. 15.50 10.41
2. 17.74 11.92
3. 22 36 49 22 35 47
4. 25 32 37 24 30 36
5. 51 88 193 53 108 398
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 26 35 20 21 29
4. 29 37 44 29 35 43
5. 49 57 66 46 57 65
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 27 33 20 31 39
4. 29 58 73 30 43 50
5. 44 61 71 52 65 76
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 46 57 36 41 50
4. 41 105 124 53 89 97
5. 112 179 223 120 202 214
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdr
|
1. 6.02 18.00
2. 6.08 18.18
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdr
|
1. 10.06 30.10
2. 10.99 32.85
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdr
|
1. 6.23 4.19
2. 6.75 4.54
3. 17 30 39 17 17 23
4. 27 43 50 24 35 45
5. 46 56 63 48 59 67
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdr
|
1. 10.30 6.92
2. 10.90 7.32
3. 17 28 35 17 25 32
4. 29 40 48 26 34 42
5. 40 54 71 43 63 82
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdr
|
1. 15.91 10.69
2. 18.04 12.12
3. 21 35 49 21 35 46
4. 26 34 40 24 30 35
5. 44 64 100 50 84 138
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 30 42 20 44 57
4. 30 44 51 29 60 69
5. 48 62 71 52 62 69
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 31 41 20 37 51
4. 29 41 50 34 59 70
5. 49 62 70 51 71 78
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 52 61 35 37 40
4. 40 229 277 50 320 337
5. 166 208 220 264 361 376
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdr
|
1. 6.28 18.79
2. 6.31 18.89
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdr
|
1. 10.17 30.40
2. 10.85 32.45
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdr
|
1. 12.75 38.14
2. 14.10 42.16
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdr
|
1. 9.38 6.31
2. 9.46 6.36
3. 17 27 32 16 17 33
4. 29 37 42 18 29 48
5. 51 63 70 51 65 76
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdr
|
1. 13.93 9.36
2. 16.28 10.94
3. 17 27 34 17 25 33
4. 30 39 45 25 31 37
5. 104 165 205 45 61 78
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdr
|
1. 20.54 13.80
2. 21.60 14.51
3. 18 30 38 20 31 42
4. 25 31 37 26 33 39
5. 34 51 69 36 52 76
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 24 34 20 47 62
4. 25 48 58 26 57 69
5. 44 57 61 49 59 65
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 20 22 20 20 29
4. 31 51 58 32 50 64
5. 52 65 78 46 61 69
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.03
3. 36 41 58 36 62 69
4. 39 235 260 54 173 185
5. 118 237 252 135 204 231
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdr
|
1. 9.37 28.03
2. 9.46 28.29
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdr
|
1. 14.47 43.26
2. 16.32 48.80
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdr
|
1. 8.86 5.95
2. 9.07 6.10
3. 17 25 33 17 29 50
4. 19 25 36 36 44 50
5. 54 68 79 51 66 79
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdr
|
1. 13.98 9.40
2. 14.41 9.68
3. 17 25 31 17 27 34
4. 27 33 38 27 38 46
5. 38 47 54 47 65 88
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdr
|
1. 17.28 11.61
2. 20.93 14.06
3. 22 33 44 23 35 49
4. 25 32 37 25 30 36
5. 31 40 50 44 105 235
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 31 37 20 25 30
4. 30 40 46 29 39 46
5. 49 61 67 47 61 68
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 20 21 20 20 21
4. 25 57 73 30 51 61
5. 57 76 82 55 72 79
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 59 67 35 37 40
4. 42 132 151 50 204 261
5. 128 203 228 178 231 238
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdr
|
1. 8.71 26.05
2. 8.95 26.76
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdr
|
1. 13.84 41.39
2. 16.34 48.86
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdr
|
1. 13.75 41.12
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdr
|
1. 9.14 6.14
2. 9.26 6.22
3. 17 24 34 16 30 35
4. 18 29 38 17 23 29
5. 53 65 76 52 66 77
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdr
|
1. 12.39 8.33
2. 12.96 8.71
3. 17 26 34 17 26 33
4. 25 33 39 25 32 39
5. 31 38 44 39 56 73
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdr
|
1. 18.89 12.69
2. 21.39 14.37
3. 17 19 32 17 27 37
4. 26 34 43 27 39 53
5. 50 81 110 52 90 156
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 20 21 20 20 28
4. 31 50 59 28 48 55
5. 52 62 69 44 57 64
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 26 34 20 27 31
4. 29 40 49 28 40 48
5. 48 55 60 46 61 66
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 40 46 35 37 52
4. 39 247 299 39 248 263
5. 197 320 330 173 332 345
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdr
|
1. 9.06 27.09
2. 9.20 27.51
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdr
|
1. 8.66 25.91
2. 9.01 26.95
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdr
|
1. 5.71 3.83
2. 5.77 3.88
3. 17 25 33 16 17 25
4. 23 54 62 23 55 64
5. 50 63 69 59 74 98
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdr
|
1. 10.40 6.99
2. 10.66 7.16
3. 17 27 35 17 24 33
4. 27 39 47 28 36 44
5. 45 55 66 57 74 96
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdr
|
1. 14.03 9.43
2. 17.06 11.47
3. 17 29 44 17 26 35
4. 29 37 44 28 36 43
5. 50 88 231 47 67 95
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 32 38 20 30 36
4. 32 44 52 28 48 57
5. 55 59 62 47 71 82
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 22 31 20 28 36
4. 30 42 49 29 39 48
5. 51 62 72 39 52 61
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 45 55 35 54 59
4. 41 146 177 46 100 128
5. 151 291 303 111 145 164
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdr
|
1. 5.71 17.08
2. 5.80 17.33
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdr
|
1. 10.24 30.63
2. 10.53 31.50
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdr
|
1. 16.14 48.27
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdr
|
1. 5.50 3.70
2. 5.63 3.78
3. 17 27 36 16 18 63
4. 27 52 62 28 59 68
5. 52 64 76 59 72 91
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdr
|
1. 7.61 5.12
2. 9.64 6.48
3. 17 26 33 17 29 36
4. 28 37 45 31 40 50
5. 37 46 53 61 112 247
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdr
|
1. 15.08 10.13
2. 16.51 11.09
3. 17 32 45 17 30 44
4. 27 35 42 26 32 38
5. 36 47 57 45 64 95
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdr
|
1. 3.90 47.98
2. 3.92 48.23
3. 20 29 42 20 38 50
4. 31 53 63 34 64 74
5. 57 73 82 57 70 79
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 33 42 20 33 39
4. 29 39 46 32 52 62
5. 49 58 67 43 53 59
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 47 51 35 37 42
4. 61 208 231 42 169 177
5. 120 158 223 148 252 267
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdr
|
1. 5.46 16.32
2. 5.57 16.65
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdr
|
1. 7.49 22.40
2. 9.54 28.54
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdr
|
1. 16.14 48.27
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdr
|
1. 5.62 3.77
2. 5.71 3.83
3. 17 34 45 16 20 32
4. 25 51 60 29 57 65
5. 47 63 74 59 76 93
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdr
|
1. 8.43 5.67
2. 9.95 6.69
3. 17 21 29 17 27 33
4. 25 34 40 27 37 48
5. 34 42 48 64 122 241
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdr
|
1. 15.13 10.17
2. 16.56 11.13
3. 17 30 37 18 29 39
4. 26 34 44 27 38 49
5. 36 46 57 48 68 98
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 21 26 20 20 25
4. 35 51 58 34 51 63
5. 52 62 67 45 67 74
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 24 32 20 30 40
4. 27 42 49 29 44 53
5. 53 70 76 50 64 70
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 48 57 35 40 49
4. 39 230 243 51 308 334
5. 198 319 331 239 319 327
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdr
|
1. 5.59 16.70
2. 5.67 16.96
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdr
|
1. 9.60 28.71
2. 10.29 30.78
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdr
|
1. 14.31 42.80
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-ndrpdr
RFC2544: Pkt throughput L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-
eth-l2bdbasemaclrn-ndrpdr
|
1. 24.39 16.39
2. 24.84 16.69
3. 17 24 31 18 29 35
4. 28 33 38 28 35 40
5. 51 56 62 51 58 64
|
64b-4t2c-avf-
eth-l2bdbasemaclrn-ndrpdr
|
1. 37.13 24.95
2. 37.31 25.07
3. 20 27 34 20 28 36
4. 26 30 33 25 29 32
5. 35 38 41 34 38 42
|
64b-8t4c-avf-
eth-l2bdbasemaclrn-ndrpdr
|
1. 33.07 22.23
2. 33.95 22.81
3. 22 34 48 23 37 49
4. 24 28 34 23 28 34
5. 28 31 35 27 31 34
|
1518b-2t1c-avf-
eth-l2bdbasemaclrn-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 21 27 20 27 35
4. 28 44 54 28 45 52
5. 38 57 64 38 67 72
|
1518b-4t2c-avf-
eth-l2bdbasemaclrn-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 21 25 20 26 31
4. 31 48 58 29 38 47
5. 46 55 59 41 54 60
|
9000b-2t1c-avf-
eth-l2bdbasemaclrn-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 36 38 35 37 39
4. 45 96 133 44 162 183
5. 76 133 155 138 228 255
|
imix-2t1c-avf-
eth-l2bdbasemaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-4t2c-avf-
eth-l2bdbasemaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-8t4c-avf-
eth-l2bdbasemaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 8.11 5.45
2. 12.05 8.10
3. 22 32 37 17 24 31
4. 29 40 47 26 37 49
5. 48 56 63 48 57 65
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 16.92 11.37
2. 23.86 16.03
3. 24 30 37 22 30 36
4. 27 33 37 27 32 36
5. 47 53 60 45 55 62
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 30.73 20.65
2. 32.31 21.71
3. 24 35 45 24 35 48
4. 25 29 33 25 29 33
5. 31 35 38 31 34 38
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 29 36 20 27 34
4. 28 44 55 30 46 54
5. 44 60 70 42 58 69
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 30 35 20 21 30
4. 30 39 47 30 46 55
5. 48 62 76 45 58 65
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 42 56 35 44 50
4. 42 165 194 43 238 252
5. 123 156 178 123 256 266
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 9.88 29.55
2. 12.05 36.05
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 7.49 5.03
2. 11.02 7.40
3. 17 29 36 20 30 35
4. 28 36 43 27 36 42
5. 52 61 67 52 61 70
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 16.46 11.06
2. 21.66 14.55
3. 21 29 35 17 27 32
4. 29 34 38 27 32 36
5. 50 58 65 50 59 67
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 31.27 21.01
2. 32.06 21.54
3. 25 37 49 24 35 47
4. 27 31 37 26 31 36
5. 34 38 43 33 38 43
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 3.88 47.70
2. 3.92 48.18
3. 20 23 34 20 27 33
4. 25 38 50 27 45 59
5. 45 56 64 41 50 56
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 3.86 47.53
2. 3.92 48.26
3. 20 22 35 20 21 30
4. 29 39 47 28 38 45
5. 44 52 58 41 52 61
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 49 55 35 38 52
4. 41 160 174 51 239 255
5. 127 193 208 123 226 238
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 8.47 25.34
2. 10.44 31.21
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 14.75 44.10
2. 16.32 48.82
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 7.77 5.22
2. 11.87 7.97
3. 17 31 33 17 17 18
4. 27 34 40 27 34 41
5. 50 60 67 49 59 67
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 16.87 11.34
2. 23.83 16.01
3. 22 31 39 20 29 35
4. 28 34 40 28 34 39
5. 49 56 63 47 54 60
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 31.11 20.91
2. 32.12 21.59
3. 23 36 50 22 34 44
4. 24 27 31 25 29 33
5. 31 36 40 31 35 39
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 22 32 20 22 29
4. 28 46 56 27 41 49
5. 47 58 69 43 57 67
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 27 31 20 27 39
4. 28 46 57 28 38 46
5. 48 55 59 43 54 61
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 58 66 35 65 75
4. 41 239 262 40 126 139
5. 222 300 312 132 219 228
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 9.48 28.36
2. 12.03 35.96
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.38 49.00
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.31 48.79
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 7.61 5.11
2. 9.98 6.70
3. 17 23 31 17 25 34
4. 27 38 44 25 35 44
5. 49 58 65 48 58 66
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 13.80 9.27
2. 16.33 10.97
3. 18 30 37 17 27 34
4. 28 34 40 26 31 37
5. 53 93 148 43 60 80
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 20.36 13.68
2. 23.05 15.49
3. 20 23 38 25 39 54
4. 22 26 32 24 28 33
5. 36 45 54 41 55 73
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 21 28 20 27 33
4. 30 56 67 29 43 51
5. 44 55 62 40 54 61
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 27 36 20 21 29
4. 31 50 59 29 47 57
5. 46 56 62 45 55 62
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 77 89 35 91 103
4. 39 325 344 38 306 347
5. 185 308 321 172 302 331
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 8.27 24.75
2. 9.96 29.80
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 14.75 44.10
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 7.50 5.04
2. 9.91 6.66
3. 17 24 32 17 26 32
4. 29 38 45 25 39 49
5. 49 58 65 50 62 72
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 14.17 9.52
2. 15.90 10.69
3. 17 27 33 17 26 31
4. 26 32 37 26 32 37
5. 41 55 71 38 50 63
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 21.88 14.71
2. 24.40 16.40
3. 26 39 50 25 36 46
4. 26 31 36 25 30 34
5. 42 57 75 41 57 76
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 21 23 20 29 35
4. 29 43 49 27 39 47
5. 43 55 61 48 65 73
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 21 32 20 20 21
4. 31 40 47 35 52 66
5. 47 63 68 48 58 70
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 45 63 35 55 66
4. 39 323 344 47 280 292
5. 208 345 369 276 368 377
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 8.20 24.53
2. 9.89 29.58
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 14.24 42.58
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.38 49.00
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 7.15 4.80
2. 10.01 6.73
3. 17 27 38 17 27 36
4. 29 39 47 26 36 44
5. 49 57 64 49 57 66
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 13.31 8.95
2. 15.28 10.27
3. 17 26 35 17 17 29
4. 26 33 39 25 31 36
5. 36 46 57 37 49 60
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 22.48 15.11
2. 24.77 16.65
3. 21 33 48 22 32 44
4. 27 33 38 25 33 38
5. 41 55 71 41 55 72
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 23 32 20 29 40
4. 29 40 49 27 51 64
5. 51 64 74 51 69 75
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 24 31 20 30 44
4. 29 51 64 29 38 46
5. 47 55 60 41 55 72
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.03
3. 36 46 53 35 37 40
4. 52 131 149 45 175 188
5. 125 179 193 146 209 236
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 8.17 24.44
2. 9.99 29.87
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 14.38 43.01
2. 16.38 49.00
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 12.06 8.10
2. 12.00 8.06
3. 17 25 35 17 22 28
4. 28 38 44 27 40 45
5. 48 55 62 49 58 67
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 23.52 15.81
2. 23.88 16.05
3. 22 30 35 17 27 32
4. 29 35 41 26 33 37
5. 45 51 57 48 58 65
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 31.11 20.90
2. 32.06 21.54
3. 24 36 48 23 35 50
4. 24 30 34 25 31 35
5. 31 35 38 30 33 36
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 21 27 20 28 36
4. 26 44 55 28 35 43
5. 43 63 71 42 50 56
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 27 37 20 28 36
4. 30 42 50 30 39 49
5. 46 59 69 40 47 54
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 62 70 35 63 69
4. 39 244 276 38 245 264
5. 225 329 339 159 290 300
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 12.07 36.11
2. 12.12 36.23
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 14.75 44.10
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 10.70 7.19
2. 11.09 7.45
3. 17 34 41 17 23 36
4. 28 38 45 28 38 43
5. 52 62 69 53 64 72
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 21.04 14.14
2. 21.68 14.57
3. 17 28 35 22 29 35
4. 28 33 38 27 32 36
5. 50 58 65 50 58 65
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 30.94 20.79
2. 32.05 21.54
3. 24 36 49 24 35 46
4. 24 28 34 25 28 32
5. 33 38 41 33 38 41
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 3.90 47.97
2. 3.92 48.21
3. 20 24 31 20 24 37
4. 29 39 48 29 48 56
5. 47 59 66 42 54 63
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 3.90 47.94
2. 3.92 48.18
3. 20 36 55 20 45 62
4. 27 59 71 32 61 72
5. 57 73 80 59 75 82
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 37 52 57 35 42 56
4. 43 133 142 46 134 147
5. 118 158 190 174 336 344
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 10.18 30.43
2. 10.54 31.52
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 14.78 44.20
2. 16.33 48.83
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.31 48.79
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 11.89 7.99
2. 11.96 8.04
3. 21 36 42 17 18 18
4. 29 39 45 28 44 51
5. 50 59 66 49 58 65
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 23.46 15.77
2. 23.82 16.01
3. 24 29 36 18 28 36
4. 27 33 38 27 33 37
5. 47 54 59 49 56 62
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 31.04 20.86
2. 31.94 21.46
3. 24 37 50 22 34 50
4. 24 28 32 24 28 32
5. 31 34 38 31 35 38
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 28 32 20 27 35
4. 29 44 53 31 61 72
5. 51 68 79 49 56 61
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 28 33 20 28 37
4. 32 47 57 33 48 57
5. 53 69 78 42 56 64
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 62 71 35 39 42
4. 51 206 261 44 149 165
5. 167 211 220 169 270 301
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 11.81 35.33
2. 12.09 36.17
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.32 48.82
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 9.94 6.68
2. 9.99 6.71
3. 17 35 42 17 28 44
4. 30 40 46 27 40 45
5. 51 61 70 52 64 73
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 16.66 11.19
2. 17.34 11.65
3. 18 28 33 19 27 33
4. 28 34 39 27 33 38
5. 45 58 67 43 53 63
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 21.25 14.28
2. 22.40 15.06
3. 22 34 45 24 37 48
4. 26 33 40 26 34 41
5. 38 52 69 40 55 76
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 21 27 20 21 21
4. 28 42 51 29 47 56
5. 45 55 61 46 60 67
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 21 23 20 25 33
4. 29 42 54 30 41 49
5. 48 55 59 48 59 67
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 65 75 35 64 78
4. 39 167 182 38 182 192
5. 152 279 304 107 140 151
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 9.74 29.12
2. 9.86 29.48
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.31 48.79
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 9.91 6.66
2. 10.01 6.73
3. 17 21 39 17 33 47
4. 34 46 55 38 48 54
5. 52 61 69 51 62 71
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 15.39 10.34
2. 15.94 10.71
3. 17 28 35 17 25 34
4. 28 34 41 28 39 43
5. 42 57 74 41 56 72
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 19.65 13.20
2. 20.76 13.95
3. 22 34 45 21 33 48
4. 25 32 37 24 29 35
5. 36 49 68 29 36 44
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 25 36 20 29 35
4. 32 44 53 29 38 45
5. 41 49 53 41 55 65
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 31 36 20 29 35
4. 30 40 45 34 51 58
5. 42 52 60 43 55 63
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 40 49 35 56 63
4. 38 137 149 39 255 269
5. 142 204 225 242 345 357
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 9.92 29.67
2. 9.97 29.82
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 14.75 44.10
2. 15.66 46.84
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 9.80 6.59
2. 9.80 6.59
3. 17 24 37 17 22 38
4. 29 37 42 27 39 44
5. 50 59 68 51 62 72
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 15.14 10.17
2. 16.19 10.88
3. 17 30 37 17 27 33
4. 27 35 41 27 33 38
5. 44 60 79 41 57 74
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 22.54 15.15
2. 23.77 15.97
3. 28 42 53 26 36 55
4. 28 34 39 26 29 35
5. 41 56 74 37 48 60
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 23 34 20 32 38
4. 27 36 44 26 40 48
5. 51 56 64 44 67 72
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 39 47 20 27 34
4. 33 50 59 31 52 63
5. 55 68 77 48 68 75
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 39 41 35 51 59
4. 38 230 261 38 194 207
5. 199 277 299 122 192 200
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 9.89 29.57
2. 9.98 29.86
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 14.38 43.01
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 11.99 8.06
2. 12.01 8.07
3. 17 22 32 17 18 20
4. 28 38 45 27 35 43
5. 51 59 68 52 61 71
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 23.58 15.85
2. 23.94 16.09
3. 23 29 35 17 28 37
4. 27 32 36 26 31 35
5. 46 53 59 45 55 61
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 31.17 20.94
2. 32.12 21.58
3. 23 36 50 23 35 48
4. 23 27 32 25 29 34
5. 31 35 39 30 34 37
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 21 24 20 20 25
4. 30 42 51 29 45 54
5. 45 52 61 49 64 72
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 27 34 20 21 32
4. 29 42 50 29 48 58
5. 48 58 71 46 68 76
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 47 56 35 39 46
4. 39 199 211 62 247 264
5. 198 275 293 205 284 293
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 12.01 35.92
2. 12.07 36.10
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 10.75 7.22
2. 11.07 7.44
3. 17 21 31 17 34 43
4. 29 42 48 32 42 47
5. 53 63 70 56 68 77
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 20.06 13.48
2. 21.61 14.52
3. 17 23 32 17 17 26
4. 29 35 39 29 34 39
5. 50 59 68 52 61 71
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 31.19 20.96
2. 32.15 21.60
3. 23 35 47 22 34 48
4. 25 28 32 25 30 34
5. 34 38 41 34 38 42
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 3.90 47.96
2. 3.92 48.20
3. 20 26 37 20 38 50
4. 30 45 54 30 50 58
5. 51 59 68 52 60 65
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 3.89 47.91
2. 3.91 48.15
3. 20 31 41 20 32 51
4. 31 49 56 31 44 53
5. 48 62 69 41 49 54
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 37 64 75 35 54 59
4. 41 138 156 41 221 238
5. 128 195 208 145 272 281
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 10.04 30.02
2. 10.45 31.25
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 14.86 44.45
2. 16.05 48.01
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 11.74 7.89
2. 11.92 8.01
3. 17 22 33 18 39 46
4. 31 43 49 28 43 50
5. 50 59 66 49 58 66
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 23.48 15.78
2. 23.71 15.94
3. 25 30 35 17 18 20
4. 27 32 35 27 32 36
5. 48 55 62 48 55 62
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 31.12 20.91
2. 31.91 21.44
3. 21 36 48 18 33 46
4. 25 29 33 25 29 33
5. 31 35 38 31 35 39
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 25 31 20 21 27
4. 30 55 71 31 52 65
5. 47 71 76 49 61 66
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 29 34 20 26 35
4. 29 40 53 25 45 56
5. 50 57 61 48 56 62
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 58 70 35 61 68
4. 38 249 267 37 244 255
5. 150 226 234 143 226 240
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 11.87 35.50
2. 12.04 36.01
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 9.95 6.69
2. 10.00 6.72
3. 17 22 41 17 30 40
4. 30 41 47 28 46 53
5. 51 60 67 50 61 69
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 15.44 10.38
2. 16.50 11.09
3. 17 25 30 17 26 32
4. 27 33 37 26 32 36
5. 39 50 64 197 221 231
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 23.26 15.63
2. 24.63 16.55
3. 21 35 46 21 34 43
4. 27 31 35 25 30 34
5. 44 60 79 38 50 64
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 21 28 34 20 21 22
4. 25 41 52 29 42 50
5. 42 64 70 43 56 63
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 26 33 20 22 33
4. 30 41 51 30 43 52
5. 45 60 70 41 57 67
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 38 47 35 37 39
4. 39 153 176 56 223 236
5. 154 213 223 161 235 243
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 9.99 29.87
2. 9.99 29.87
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.38 49.00
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 9.92 6.66
2. 9.97 6.70
3. 17 22 42 17 24 46
4. 36 46 52 32 46 52
5. 51 60 69 50 62 71
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 15.07 10.13
2. 15.90 10.68
3. 17 28 36 17 17 25
4. 28 35 41 27 35 40
5. 42 55 70 46 60 78
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 23.31 15.67
2. 24.74 16.63
3. 24 37 49 21 36 50
4. 26 32 36 25 30 35
5. 41 54 72 40 53 68
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 25 33 21 31 37
4. 28 42 51 30 43 51
5. 53 67 75 48 72 81
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 37 49 20 25 32
4. 27 47 59 31 52 61
5. 55 70 80 56 70 75
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 37 39 35 52 60
4. 39 330 355 38 243 262
5. 184 309 320 185 318 332
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 9.82 29.38
2. 9.82 29.38
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 13.70 40.99
2. 14.83 44.35
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 9.91 6.66
2. 9.96 6.70
3. 17 25 33 17 24 40
4. 31 42 48 31 44 50
5. 50 62 74 51 62 69
|
64b-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 15.94 10.71
2. 18.01 12.10
3. 17 25 31 17 26 32
4. 28 34 39 26 31 36
5. 72 116 160 57 82 111
|
64b-8t4c-avf-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 22.87 15.37
2. 24.16 16.23
3. 25 33 44 25 35 47
4. 26 32 37 26 32 36
5. 40 54 70 38 50 62
|
1518b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 22 30 20 29 35
4. 26 46 57 28 51 59
5. 54 73 78 40 53 67
|
1518b-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 30 35 20 39 62
4. 29 41 50 27 60 75
5. 56 73 81 52 77 84
|
9000b-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 50 58 35 48 61
4. 40 162 181 44 174 212
5. 167 297 313 129 248 263
|
imix-2t1c-avf-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 9.90 29.59
2. 9.96 29.78
|
imix-4t2c-avf-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 14.45 43.23
2. 16.30 48.76
|
imix-8t4c-avf-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdscale100kmaclrn-ndrpdr
RFC2544: Pkt throughput for L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 50k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 9.63 6.47
2. 18.48 12.42
3. 17 25 31 17 26 32
4. 30 37 43 27 34 40
5. 55 62 68 57 64 70
|
64b-4t2c-avf-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 24.73 16.62
2. 36.72 24.68
3. 22 29 35 21 29 37
4. 27 32 36 28 32 36
5. 58 64 70 58 64 70
|
64b-8t4c-avf-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 35.87 24.11
2. 36.41 24.47
3. 24 34 43 25 35 44
4. 25 30 34 25 29 33
5. 30 34 39 30 33 38
|
1518b-2t1c-avf-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 24 33 20 21 26
4. 27 40 53 27 38 47
5. 48 59 72 39 62 70
|
1518b-4t2c-avf-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 26 33 20 23 32
4. 30 42 50 31 50 59
5. 52 69 76 40 49 55
|
9000b-2t1c-avf-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 37 52 35 38 41
4. 68 236 271 39 170 187
5. 178 224 278 116 211 226
|
imix-2t1c-avf-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 16.34 48.87
2. 16.34 48.87
|
imix-4t2c-avf-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-8t4c-avf-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdscale10kmaclrn-ndrpdr
RFC2544: Pkt throughput for L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 5k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 9.13 6.13
2. 20.38 13.70
3. 17 26 33 17 26 33
4. 29 36 42 30 39 46
5. 49 55 62 59 67 74
|
64b-4t2c-avf-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 35.49 23.85
2. 37.31 25.07
3. 21 30 36 21 29 35
4. 27 30 34 25 29 32
5. 43 46 51 43 47 53
|
64b-8t4c-avf-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 33.65 22.61
2. 34.85 23.42
3. 23 35 46 22 31 40
4. 24 28 35 24 28 33
5. 29 33 36 28 32 35
|
1518b-2t1c-avf-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 27 35 20 28 36
4. 30 41 50 27 46 56
5. 41 50 58 39 52 62
|
1518b-4t2c-avf-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 21 27 20 25 31
4. 29 40 47 31 45 54
5. 43 53 60 48 69 75
|
9000b-2t1c-avf-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 37 40 35 37 40
4. 46 139 169 47 177 192
5. 165 235 250 162 270 289
|
imix-2t1c-avf-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 16.38 49.00
2. 16.38 49.00
|
imix-4t2c-avf-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-8t4c-avf-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2bdscale1mmaclrn-ndrpdr
RFC2544: Pkt throughput for L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 500k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 8.56 5.75
2. 16.74 11.25
3. 17 34 38 17 27 35
4. 33 41 49 30 37 46
5. 65 81 102 57 66 74
|
64b-4t2c-avf-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 19.61 13.18
2. 30.64 20.59
3. 21 30 39 20 27 34
4. 29 34 38 28 32 36
5. 57 70 84 55 63 70
|
64b-8t4c-avf-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 36.35 24.43
2. 36.90 24.80
3. 24 35 46 25 37 48
4. 24 29 32 25 29 32
5. 32 36 41 32 36 43
|
1518b-2t1c-avf-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 24 28 20 26 35
4. 26 37 47 30 42 51
5. 42 54 62 42 51 58
|
1518b-4t2c-avf-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 21 30 20 20 23
4. 29 38 44 29 42 52
5. 45 53 61 46 59 70
|
9000b-2t1c-avf-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 37 51 35 56 67
4. 50 195 211 39 257 297
5. 162 247 290 158 284 294
|
imix-2t1c-avf-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 10.43 31.20
2. 14.27 42.67
|
imix-4t2c-avf-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-8t4c-avf-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2patch-ndrpdr
RFC2544: Pkt throughput L2patch test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 patch DUT1 and DUT2 tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header,IPv4 header with static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-
eth-l2patch-ndrpdr
|
1. 33.25 22.34
2. 37.31 25.07
3. 18 24 31 16 22 28
4. 21 25 29 21 25 28
5. 26 29 31 26 29 31
|
64b-4t2c-avf-
eth-l2patch-ndrpdr
|
1. 33.94 22.81
2. 35.32 23.74
3. 18 25 31 15 25 34
4. 20 24 29 21 25 29
5. 24 26 29 24 27 30
|
64b-8t4c-avf-
eth-l2patch-ndrpdr
|
1. 30.33 20.38
2. 31.10 20.90
3. 21 34 43 22 34 46
4. 20 23 29 20 25 28
5. 23 26 29 23 26 29
|
1518b-2t1c-avf-
eth-l2patch-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 18 19 22 18 34 44
4. 24 50 63 22 42 52
5. 37 51 59 43 53 60
|
1518b-4t2c-avf-
eth-l2patch-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 18 20 30 18 30 37
4. 29 51 67 29 41 51
5. 49 61 69 42 59 67
|
9000b-2t1c-avf-
eth-l2patch-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 34 38 42 33 69 80
4. 37 124 159 56 190 211
5. 145 198 217 189 263 270
|
imix-2t1c-avf-
eth-l2patch-ndrpdr
|
1. 15.05 45.00
2. 16.30 48.76
|
imix-4t2c-avf-
eth-l2patch-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-8t4c-avf-
eth-l2patch-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-avf-eth-l2xcbase-ndrpdr
RFC2544: Pkt throughput L2XC test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-avf-
eth-l2xcbase-ndrpdr
|
1. 30.24 20.32
2. 37.39 25.13
3. 19 25 32 17 24 29
4. 28 33 35 27 32 35
5. 37 40 44 37 41 46
|
64b-4t2c-avf-
eth-l2xcbase-ndrpdr
|
1. 36.04 24.22
2. 36.70 24.66
3. 20 28 35 20 28 35
4. 21 24 27 22 25 28
5. 26 30 33 26 29 32
|
64b-8t4c-avf-
eth-l2xcbase-ndrpdr
|
1. 30.89 20.76
2. 31.84 21.40
3. 18 33 45 19 32 44
4. 22 26 29 22 26 29
5. 25 28 31 25 29 32
|
1518b-2t1c-avf-
eth-l2xcbase-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 19 23 41 19 37 56
4. 23 45 62 29 58 71
5. 51 73 79 45 67 72
|
1518b-4t2c-avf-
eth-l2xcbase-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 19 20 21 19 26 33
4. 28 38 47 27 41 54
5. 42 57 64 42 54 66
|
9000b-2t1c-avf-
eth-l2xcbase-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 35 52 59 34 47 56
4. 40 111 151 76 145 200
5. 140 226 278 107 216 226
|
imix-2t1c-avf-
eth-l2xcbase-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-4t2c-avf-
eth-l2xcbase-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-8t4c-avf-
eth-l2xcbase-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-dot1q-l2bdbasemaclrn-ndrpdr
RFC2544: Pkt throughput L2BD with IEEE 802.1Q test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge domain and MAC learning enabled. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 14.60 10.28
2. 14.67 10.33
3. 21 47 79 17 44 70
4. 34 44 51 35 44 51
5. 59 70 79 57 66 73
|
64b-4t2c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 28.77 20.25
2. 29.06 20.46
3. 28 47 71 28 47 67
4. 29 38 42 29 37 41
5. 60 69 77 60 68 76
|
64b-8t4c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 35.74 25.16
2. 36.28 25.54
3. 26 38 48 31 50 65
4. 26 32 35 26 32 35
5. 31 35 41 31 35 40
|
1518b-2t1c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 3.89 48.03
2. 3.91 48.27
3. 20 48 79 20 51 87
4. 32 52 64 34 48 68
5. 42 52 58 46 57 63
|
1518b-4t2c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 3.89 48.01
2. 3.91 48.25
3. 20 45 78 20 33 59
4. 41 67 95 50 82 112
5. 56 71 81 39 70 74
|
9000b-2t1c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 0.66 47.95
2. 0.67 48.19
3. 37 59 71 36 60 90
4. 59 293 332 62 269 283
5. 209 328 337 177 294 315
|
imix-2t1c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 11.76 35.56
2. 11.83 35.75
|
imix-4t2c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 16.13 48.76
2. 16.13 48.76
|
imix-8t4c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 16.13 48.76
2. 16.13 48.76
|
25ge2p1xxv710-dot1q-l2xcbase-ndrpdr
RFC2544: Pkt throughput L2XC with IEEE 802.1Q test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-dot1q-l2xcbase-ndrpdr
|
1. 18.74 13.19
2. 18.93 13.33
3. 17 45 66 18 45 65
4. 26 33 38 30 39 46
5. 48 56 64 49 57 65
|
64b-4t2c-dot1q-l2xcbase-ndrpdr
|
1. 36.94 26.01
2. 37.31 26.27
3. 23 34 44 28 45 61
4. 25 29 33 25 29 33
5. 47 53 59 49 55 61
|
64b-8t4c-dot1q-l2xcbase-ndrpdr
|
1. 33.48 23.57
2. 34.71 24.44
3. 30 46 65 34 56 73
4. 23 26 31 21 25 29
5. 28 32 35 28 32 36
|
1518b-2t1c-
dot1q-l2xcbase-ndrpdr
|
1. 3.89 48.03
2. 3.91 48.27
3. 25 47 67 20 60 92
4. 29 42 57 41 63 89
5. 36 47 55 36 43 49
|
1518b-4t2c-
dot1q-l2xcbase-ndrpdr
|
1. 3.89 48.01
2. 3.91 48.25
3. 20 40 69 19 58 90
4. 37 55 63 49 76 110
5. 52 70 81 45 77 83
|
9000b-2t1c-
dot1q-l2xcbase-ndrpdr
|
1. 0.66 47.95
2. 0.67 48.19
3. 36 66 90 35 59 65
4. 57 333 351 39 235 255
5. 208 327 344 181 309 323
|
imix-2t1c-
dot1q-l2xcbase-ndrpdr
|
1. 14.20 42.93
2. 14.36 43.39
|
imix-4t2c-
dot1q-l2xcbase-ndrpdr
|
1. 16.13 48.76
2. 16.13 48.76
|
imix-8t4c-
dot1q-l2xcbase-ndrpdr
|
1. 16.13 48.76
2. 16.13 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 11.14 7.49
2. 11.37 7.64
3. 19 33 46 29 69 79
4. 34 45 52 32 43 51
5. 53 63 74 53 65 74
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 19.99 13.44
2. 20.38 13.70
3. 26 51 66 31 49 68
4. 26 33 39 26 32 37
5. 37 43 49 46 60 70
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 32.53 21.86
2. 34.20 22.98
3. 32 42 51 29 44 54
4. 25 29 33 24 28 31
5. 35 40 45 34 42 48
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 42 73 20 40 76
4. 32 54 90 33 49 74
5. 42 51 56 38 48 55
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 40 85 21 43 73
4. 36 66 100 33 53 67
5. 47 56 63 40 48 55
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 37 68 93 36 67 99
4. 72 224 242 65 164 177
5. 196 316 332 120 162 171
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 11.24 33.61
2. 11.36 33.99
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 14.75 44.10
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 9.44 6.35
2. 9.83 6.61
3. 19 45 72 24 47 64
4. 31 43 55 31 42 51
5. 53 64 73 51 62 73
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 18.86 12.67
2. 19.24 12.93
3. 29 54 72 32 55 69
4. 29 36 44 27 34 40
5. 55 66 75 52 63 74
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 33.11 22.25
2. 34.99 23.51
3. 29 39 45 29 47 55
4. 26 30 36 26 30 35
5. 47 56 67 45 56 67
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 3.89 47.83
2. 3.93 48.31
3. 21 45 77 31 62 82
4. 32 47 74 35 50 64
5. 45 57 66 38 48 55
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 3.88 47.68
2. 3.91 48.16
3. 21 40 63 20 42 71
4. 33 47 57 35 62 80
5. 45 55 61 42 54 61
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 46 78 36 58 80
4. 67 219 249 40 331 341
5. 109 147 162 215 294 305
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 9.04 27.02
2. 9.31 27.85
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 14.75 44.11
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 10.78 7.24
2. 10.94 7.35
3. 31 54 73 31 51 67
4. 34 44 54 30 39 47
5. 56 67 76 56 70 80
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 21.04 14.14
2. 21.47 14.43
3. 32 47 64 35 52 67
4. 28 34 39 28 36 40
5. 50 59 67 50 59 67
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 32.96 22.15
2. 34.20 22.98
3. 25 39 51 25 41 61
4. 25 28 32 24 28 31
5. 35 40 45 33 37 42
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 21 42 69 20 62 93
4. 38 57 73 43 66 90
5. 45 55 60 52 61 68
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 24 71 80 20 53 90
4. 34 56 83 36 55 75
5. 51 63 78 50 63 72
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 40 87 35 38 55
4. 77 275 306 50 143 160
5. 122 276 286 120 171 186
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 10.53 31.50
2. 10.75 32.15
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 9.42 6.33
2. 9.75 6.55
3. 28 54 76 17 37 72
4. 33 42 51 32 41 48
5. 64 76 90 61 74 85
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 14.44 9.70
2. 15.80 10.62
3. 37 66 81 31 49 70
4. 29 38 48 26 32 38
5. 52 69 94 44 62 72
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 21.31 14.32
2. 23.04 15.48
3. 22 29 39 34 45 52
4. 26 31 38 26 32 38
5. 34 44 55 33 45 56
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 49 83 21 51 78
4. 32 57 87 34 58 78
5. 43 52 56 40 52 60
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 38 70 20 47 72
4. 34 52 82 41 63 92
5. 46 56 61 45 55 59
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 37 63 109 36 55 95
4. 52 220 274 59 242 265
5. 197 306 318 126 233 242
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 9.38 28.04
2. 9.72 29.06
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 9.30 6.25
2. 9.64 6.48
3. 26 57 76 17 53 75
4. 34 46 57 35 49 58
5. 62 74 85 58 72 82
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 14.96 10.06
2. 16.87 11.34
3. 28 45 63 32 55 71
4. 27 36 45 29 37 45
5. 77 168 230 60 118 173
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 22.74 15.28
2. 24.28 16.31
3. 34 54 68 30 46 59
4. 26 31 37 25 30 36
5. 40 57 83 40 57 77
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 29 41 20 24 42
4. 39 71 110 34 58 73
5. 40 52 61 39 48 59
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 22 47 66 20 35 43
4. 31 51 69 33 52 72
5. 44 55 62 44 61 71
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 0.66 47.55
2. 0.67 48.27
3. 37 38 86 36 52 66
4. 57 189 218 48 269 294
5. 115 174 181 223 363 376
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 9.40 28.11
2. 9.62 28.76
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.38 49.00
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 9.40 6.32
2. 9.64 6.48
3. 29 50 72 28 46 71
4. 38 53 65 31 41 49
5. 62 73 84 59 72 81
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 15.39 10.34
2. 17.01 11.43
3. 31 47 74 30 47 69
4. 29 35 43 29 37 45
5. 79 158 214 72 143 193
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 21.40 14.38
2. 23.42 15.74
3. 41 66 81 27 36 47
4. 27 33 39 25 31 37
5. 38 49 61 40 56 77
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 21 41 57 24 59 71
4. 35 49 80 31 45 71
5. 42 51 58 42 56 67
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 21 44 67 22 48 79
4. 40 57 70 36 56 82
5. 50 59 66 43 50 56
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 0.66 47.55
2. 0.67 48.27
3. 37 59 66 36 59 95
4. 40 226 246 65 125 160
5. 127 198 209 104 179 191
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 9.25 27.67
2. 9.62 28.78
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 14.60 43.66
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 11.22 7.54
2. 11.39 7.65
3. 21 39 68 23 56 73
4. 37 51 62 36 48 57
5. 55 66 76 55 68 78
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 19.95 13.41
2. 20.37 13.69
3. 23 43 67 23 47 71
4. 29 35 42 25 31 36
5. 39 45 52 47 62 72
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 32.81 22.05
2. 34.67 23.30
3. 21 36 59 33 50 69
4. 25 29 32 24 29 32
5. 36 41 47 36 45 52
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 36 64 20 36 56
4. 35 54 75 38 57 72
5. 46 67 72 44 63 68
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 34 55 20 42 64
4. 39 56 64 35 58 83
5. 43 61 72 45 60 70
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 53 86 35 62 109
4. 54 274 285 59 316 332
5. 228 297 359 217 331 341
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 11.17 33.41
2. 11.18 33.45
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 9.57 6.43
2. 9.91 6.66
3. 17 49 71 17 42 70
4. 32 41 53 33 47 57
5. 57 69 80 54 67 78
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 18.72 12.58
2. 19.19 12.90
3. 27 47 65 27 48 62
4. 28 33 38 28 33 39
5. 52 62 70 47 56 65
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 33.10 22.24
2. 34.49 23.18
3. 22 45 55 31 42 50
4. 25 29 32 26 30 34
5. 47 56 64 43 50 57
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 3.89 47.85
2. 3.93 48.32
3. 21 36 59 22 47 74
4. 32 44 61 36 56 84
5. 46 55 64 45 53 62
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 3.90 47.94
2. 3.92 48.18
3. 20 31 43 28 58 83
4. 40 58 72 38 57 79
5. 53 62 76 44 54 62
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 70 80 36 50 77
4. 46 160 211 54 120 140
5. 176 237 278 144 305 313
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 9.01 26.94
2. 9.38 28.05
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 14.77 44.19
2. 16.33 48.85
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 10.81 7.26
2. 11.03 7.41
3. 20 48 74 17 57 75
4. 33 41 53 34 47 55
5. 55 67 79 52 64 75
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 21.43 14.40
2. 21.65 14.55
3. 26 44 56 32 52 69
4. 28 33 39 27 32 37
5. 56 65 72 50 60 68
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 33.10 22.24
2. 34.15 22.95
3. 21 32 39 25 37 57
4. 25 29 32 25 29 33
5. 34 38 42 34 39 43
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 42 71 20 25 71
4. 35 51 62 40 76 108
5. 54 71 78 49 72 75
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 42 67 20 39 78
4. 37 51 61 45 80 113
5. 45 65 70 55 71 85
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 53 84 36 43 85
4. 46 141 164 45 310 347
5. 229 285 301 229 344 350
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 10.54 31.52
2. 10.71 32.04
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 14.75 44.10
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 9.41 6.32
2. 9.74 6.55
3. 17 50 73 16 42 64
4. 32 42 47 38 50 61
5. 65 79 94 65 79 89
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 15.32 10.29
2. 15.99 10.75
3. 25 43 71 23 46 72
4. 28 34 41 27 33 40
5. 51 75 121 44 62 73
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 22.46 15.10
2. 22.92 15.40
3. 23 36 46 41 57 68
4. 25 29 36 26 32 38
5. 36 47 59 37 49 60
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 39 65 20 26 46
4. 37 57 77 33 54 80
5. 50 65 71 44 57 63
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 40 72 20 42 74
4. 37 55 62 40 71 96
5. 52 69 74 56 72 81
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 54 85 36 39 86
4. 59 306 343 74 303 312
5. 186 308 322 264 362 372
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 9.68 28.94
2. 9.73 29.11
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 14.75 44.10
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 9.38 6.30
2. 9.66 6.49
3. 17 49 79 17 45 63
4. 32 41 48 32 43 51
5. 67 81 96 63 77 87
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 15.17 10.19
2. 16.94 11.38
3. 30 53 73 27 55 69
4. 30 38 46 27 34 41
5. 72 151 202 76 155 214
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 21.83 14.67
2. 23.30 15.66
3. 26 31 65 34 57 72
4. 28 34 43 25 30 35
5. 38 48 59 41 59 83
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 34 76 21 49 75
4. 35 58 94 34 50 74
5. 45 56 62 40 52 61
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 40 74 20 42 61
4. 36 56 71 38 57 85
5. 52 60 65 48 63 76
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 37 47 52 36 59 77
4. 41 231 253 41 192 260
5. 171 237 257 150 255 263
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 9.30 27.81
2. 9.52 28.46
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 14.17 42.37
2. 16.38 49.00
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 9.44 6.34
2. 9.68 6.51
3. 19 58 72 17 45 68
4. 33 41 50 38 50 60
5. 66 81 97 62 76 85
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 15.17 10.19
2. 16.77 11.27
3. 19 49 72 19 46 68
4. 29 36 43 28 36 43
5. 78 161 217 60 107 161
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 22.19 14.91
2. 23.33 15.68
3. 26 52 64 24 32 49
4. 27 32 37 26 32 41
5. 42 58 78 36 45 56
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 37 74 20 41 55
4. 33 53 78 32 52 83
5. 41 51 55 49 61 69
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 44 73 21 51 72
4. 35 64 103 43 62 82
5. 45 67 77 57 71 77
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 53 64 36 41 85
4. 41 150 157 70 218 231
5. 149 227 239 132 204 232
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 9.35 27.95
2. 9.61 28.73
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 14.75 44.10
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 11.25 7.56
2. 11.36 7.63
3. 22 42 57 18 57 74
4. 33 45 58 35 49 60
5. 57 68 81 52 65 74
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 20.07 13.49
2. 20.38 13.69
3. 22 49 71 32 49 66
4. 28 34 41 26 35 40
5. 38 43 49 46 60 70
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 32.97 22.16
2. 34.03 22.87
3. 24 45 61 34 55 69
4. 25 29 33 25 29 33
5. 34 40 45 33 42 49
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 40 71 20 51 74
4. 39 57 75 39 70 106
5. 42 57 68 51 61 69
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 41 50 22 52 67
4. 34 52 73 35 53 72
5. 47 56 63 43 51 57
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 62 93 35 58 70
4. 58 179 206 40 255 266
5. 196 274 290 192 318 329
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 11.25 33.63
2. 11.38 34.02
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.38 49.00
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 9.54 6.41
2. 9.88 6.64
3. 17 45 52 17 39 67
4. 34 45 54 38 50 59
5. 56 68 78 53 66 77
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 18.73 12.58
2. 19.20 12.90
3. 23 45 59 28 52 72
4. 29 37 45 26 32 39
5. 52 62 71 47 57 66
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 33.22 22.33
2. 34.76 23.36
3. 33 50 54 26 42 51
4. 29 33 39 28 34 38
5. 47 54 61 44 51 58
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 3.90 47.93
2. 3.91 48.17
3. 20 38 69 26 59 79
4. 37 54 70 31 45 58
5. 47 63 71 44 54 60
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 3.90 47.93
2. 3.92 48.17
3. 21 40 68 21 58 81
4. 33 47 61 36 55 65
5. 46 68 76 48 67 80
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 37 40 57 36 60 91
4. 58 167 177 71 213 236
5. 125 222 235 151 224 236
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 9.09 27.18
2. 9.34 27.93
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 14.77 44.17
2. 16.33 48.85
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 10.83 7.28
2. 10.94 7.35
3. 20 47 73 16 41 67
4. 32 42 53 34 48 57
5. 57 69 79 58 74 83
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 21.14 14.20
2. 21.67 14.56
3. 23 45 64 19 50 69
4. 29 36 42 27 34 40
5. 51 59 67 51 61 70
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 32.73 21.99
2. 34.41 23.12
3. 22 43 60 25 49 61
4. 25 29 32 25 28 32
5. 37 41 45 34 38 42
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 47 79 20 54 67
4. 38 54 81 49 76 105
5. 43 56 67 52 65 72
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 46 81 20 39 68
4. 33 51 77 36 55 77
5. 43 52 60 46 57 65
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 52 84 35 39 50
4. 58 237 268 73 259 306
5. 201 321 332 205 283 290
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 10.63 31.80
2. 10.80 32.31
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 9.36 6.29
2. 9.70 6.52
3. 17 41 66 17 44 68
4. 36 49 61 35 49 60
5. 68 81 95 62 75 83
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 14.97 10.06
2. 15.66 10.52
3. 20 41 66 22 39 70
4. 28 36 42 27 34 40
5. 50 77 131 44 62 75
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 22.24 14.95
2. 22.95 15.42
3. 22 35 45 18 32 40
4. 26 31 35 26 32 40
5. 36 47 59 34 46 57
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 50 72 20 65 82
4. 37 56 77 37 58 74
5. 46 57 62 42 56 62
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 21 48 82 20 36 69
4. 36 64 91 39 74 94
5. 52 64 76 59 75 81
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 52 57 36 51 61
4. 47 270 285 58 170 183
5. 214 321 344 116 265 283
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 9.47 28.32
2. 9.67 28.92
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 9.36 6.29
2. 9.65 6.49
3. 23 51 72 17 46 66
4. 34 47 57 40 54 65
5. 63 77 92 63 78 90
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 15.09 10.14
2. 16.82 11.30
3. 27 47 75 31 51 73
4. 29 36 41 27 34 40
5. 72 163 225 53 95 155
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 21.97 14.76
2. 23.10 15.52
3. 21 36 53 33 44 50
4. 27 33 38 25 30 34
5. 42 57 77 35 45 55
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 38 65 20 42 79
4. 41 71 93 45 76 99
5. 54 67 78 42 60 65
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 21 45 62 20 45 78
4. 34 53 75 38 72 84
5. 51 77 83 41 51 60
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 37 60 92 36 50 95
4. 59 254 275 70 244 269
5. 201 321 329 208 284 296
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 9.40 28.12
2. 9.60 28.70
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 14.67 43.88
2. 16.31 48.79
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 9.30 6.25
2. 9.63 6.47
3. 18 48 70 16 42 72
4. 36 48 57 32 48 60
5. 68 82 96 61 75 84
|
64b-4t2c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 15.52 10.43
2. 16.98 11.41
3. 27 46 71 31 50 71
4. 29 36 42 27 33 38
5. 62 106 161 66 138 184
|
64b-8t4c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 22.69 15.25
2. 23.85 16.03
3. 28 47 69 23 37 71
4. 31 38 45 29 41 46
5. 43 58 78 39 50 65
|
1518b-2t1c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 22 51 80 20 33 72
4. 36 56 87 49 77 110
5. 53 66 74 45 63 69
|
1518b-4t2c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 36 70 20 41 66
4. 36 54 82 51 80 99
5. 49 64 69 49 73 79
|
9000b-2t1c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 37 48 55 36 55 68
4. 41 160 173 61 165 183
5. 139 179 206 156 240 247
|
imix-2t1c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 9.30 27.82
2. 9.59 28.69
|
imix-4t2c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 14.67 43.88
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 6.51 4.37
2. 6.51 4.37
3. 17 47 77 23 46 70
4. 39 54 68 31 45 56
5. 52 62 73 48 60 70
|
64b-4t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 9.15 6.15
2. 10.53 7.08
3. 36 56 79 31 55 79
4. 28 37 49 31 43 52
5. 38 49 60 69 172 294
|
64b-8t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 15.91 10.69
2. 17.32 11.64
3. 24 45 75 35 52 76
4. 28 35 45 27 35 42
5. 38 57 103 38 51 65
|
1518b-2t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 21 54 78 27 51 78
4. 37 63 76 34 51 72
5. 50 57 63 47 60 67
|
1518b-4t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 21 42 56 20 35 42
4. 32 46 61 32 46 62
5. 44 56 60 41 48 57
|
9000b-2t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 49 58 36 40 70
4. 47 126 157 51 161 179
5. 207 302 319 122 236 251
|
imix-2t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 5.87 17.55
2. 5.87 17.55
|
imix-4t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 10.36 30.97
2. 10.97 32.80
|
imix-8t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 15.90 47.55
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 5.79 3.89
2. 5.86 3.94
3. 17 58 80 17 44 66
4. 34 50 63 31 45 58
5. 45 56 66 59 73 85
|
64b-4t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 10.46 7.03
2. 10.53 7.08
3. 24 50 69 26 52 78
4. 30 41 51 29 38 46
5. 48 67 85 45 62 77
|
64b-8t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 13.02 8.75
2. 16.18 10.87
3. 32 49 71 34 53 74
4. 27 35 45 29 38 48
5. 36 48 60 40 92 519
|
1518b-2t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 21 53 74 20 36 44
4. 36 53 60 33 46 58
5. 49 67 76 44 57 68
|
1518b-4t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 21 46 77 20 46 90
4. 35 59 83 37 66 82
5. 49 63 75 48 58 70
|
9000b-2t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 0.66 47.55
2. 0.67 48.27
3. 37 52 91 36 65 92
4. 51 240 289 65 137 145
5. 113 210 220 127 175 226
|
imix-2t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 5.75 17.18
2. 5.97 17.85
|
imix-4t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 9.20 27.50
2. 9.93 29.69
|
imix-8t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 13.75 41.12
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 5.89 3.95
2. 5.97 4.01
3. 20 43 63 26 51 67
4. 30 43 54 35 48 64
5. 62 82 99 44 54 61
|
64b-4t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 10.00 6.72
2. 10.36 6.96
3. 28 54 75 33 58 77
4. 31 40 49 31 42 53
5. 44 59 76 41 55 71
|
64b-8t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 16.58 11.14
2. 17.18 11.55
3. 32 50 64 28 48 66
4. 28 36 47 26 33 40
5. 35 45 56 39 53 73
|
1518b-2t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 21 49 72 21 45 70
4. 33 53 67 35 52 81
5. 47 56 63 46 57 67
|
1518b-4t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 22 45 70 21 43 58
4. 34 56 75 37 55 76
5. 48 62 72 49 61 68
|
9000b-2t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 55 83 36 68 125
4. 56 91 123 70 130 149
5. 132 210 224 137 187 192
|
imix-2t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 5.85 17.49
2. 5.94 17.76
|
imix-4t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 9.38 28.04
2. 9.79 29.27
|
imix-8t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 8.07 5.42
2. 8.61 5.79
3. 23 49 77 16 33 56
4. 35 50 64 32 46 58
5. 62 75 86 61 78 91
|
64b-4t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 13.06 8.78
2. 13.87 9.32
3. 31 48 71 25 43 66
4. 26 33 41 29 40 49
5. 46 64 93 56 90 147
|
64b-8t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 17.08 11.48
2. 20.25 13.61
3. 22 46 71 31 50 65
4. 30 38 47 25 31 36
5. 37 57 114 35 48 67
|
1518b-2t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 51 80 20 52 76
4. 34 46 58 38 55 76
5. 42 52 58 41 66 70
|
1518b-4t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 21 54 74 21 42 73
4. 34 46 59 48 71 94
5. 45 66 73 44 60 68
|
9000b-2t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 40 67 36 60 90
4. 58 105 169 50 157 183
5. 122 197 217 94 176 205
|
imix-2t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 8.08 24.16
2. 8.58 25.67
|
imix-4t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 13.63 40.76
2. 14.31 42.80
|
imix-8t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 7.65 5.14
2. 7.96 5.35
3. 31 63 81 16 40 53
4. 37 55 69 39 58 73
5. 56 70 80 55 73 90
|
64b-4t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 11.50 7.72
2. 12.84 8.63
3. 24 42 68 17 42 76
4. 30 40 49 32 44 52
5. 51 77 121 69 141 225
|
64b-8t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 16.78 11.28
2. 19.81 13.31
3. 28 48 68 30 48 71
4. 26 32 39 26 32 39
5. 33 43 54 43 133 311
|
1518b-2t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 41 83 20 42 75
4. 35 56 72 34 49 70
5. 41 50 54 41 52 57
|
1518b-4t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 62 81 20 68 91
4. 37 63 86 52 83 114
5. 47 57 61 50 73 77
|
9000b-2t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 51 59 36 51 72
4. 62 166 176 40 237 247
5. 128 189 227 157 284 296
|
imix-2t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 7.56 22.61
2. 8.01 23.97
|
imix-4t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 12.99 38.84
2. 13.43 40.16
|
imix-8t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 7.87 5.29
2. 8.15 5.47
3. 28 61 78 16 28 45
4. 33 46 59 34 47 60
5. 54 69 80 51 63 72
|
64b-4t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 12.98 8.72
2. 13.71 9.21
3. 24 56 76 32 54 79
4. 28 39 44 27 34 42
5. 54 75 106 50 74 122
|
64b-8t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 18.51 12.44
2. 20.38 13.70
3. 26 46 66 20 50 69
4. 26 34 42 27 35 42
5. 32 41 53 37 52 79
|
1518b-2t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 26 46 20 37 50
4. 32 55 81 46 71 89
5. 51 66 72 43 62 67
|
1518b-4t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 57 72 20 42 73
4. 35 66 84 39 56 70
5. 44 56 61 51 72 78
|
9000b-2t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 59 90 36 60 92
4. 53 155 185 61 186 250
5. 118 164 212 178 311 323
|
imix-2t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 7.88 23.56
2. 8.10 24.21
|
imix-4t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 11.63 34.79
2. 13.38 40.00
|
imix-8t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 5.37 3.61
2. 5.42 3.65
3. 17 38 66 16 42 57
4. 41 56 72 40 59 72
5. 52 69 92 60 75 90
|
64b-4t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 7.19 4.83
2. 7.94 5.34
3. 35 68 81 17 37 63
4. 30 41 54 30 43 55
5. 35 44 56 44 71 116
|
64b-8t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 15.42 10.36
2. 16.38 11.01
3. 25 48 67 25 48 72
4. 28 35 44 27 36 44
5. 40 53 64 44 65 96
|
1518b-2t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 57 89 22 42 63
4. 36 50 77 35 51 71
5. 54 61 65 45 52 56
|
1518b-4t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 46 74 37 65 93
4. 43 71 85 42 63 84
5. 48 61 70 49 59 67
|
9000b-2t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 71 125 37 55 85
4. 43 177 235 61 104 127
5. 125 236 257 98 166 177
|
imix-2t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 5.35 16.00
2. 5.40 16.14
|
imix-4t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 7.90 23.62
2. 9.13 27.31
|
imix-8t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 16.06 48.03
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 5.20 3.49
2. 5.28 3.55
3. 17 56 81 16 58 67
4. 34 63 74 36 62 69
5. 60 69 93 69 89 113
|
64b-4t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 8.67 5.82
2. 9.39 6.31
3. 22 50 74 35 66 77
4. 36 55 66 34 43 49
5. 51 71 88 69 114 220
|
64b-8t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 14.47 9.72
2. 15.86 10.66
3. 32 51 71 34 54 71
4. 28 34 41 27 34 40
5. 42 64 111 47 67 94
|
1518b-2t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 51 71 21 41 66
4. 40 55 69 35 48 62
5. 53 65 75 42 55 63
|
1518b-4t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 40 71 20 45 77
4. 38 64 90 38 62 86
5. 57 73 80 42 52 58
|
9000b-2t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 57 90 36 72 94
4. 56 246 263 69 286 302
5. 201 319 333 205 319 327
|
imix-2t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 5.08 15.20
2. 5.16 15.43
|
imix-4t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 9.06 27.09
2. 9.57 28.63
|
imix-8t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 14.53 43.45
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 5.25 3.53
2. 5.30 3.56
3. 17 47 81 16 31 46
4. 34 50 64 41 60 69
5. 59 69 93 68 88 111
|
64b-4t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 9.25 6.22
2. 9.74 6.54
3. 23 46 67 16 41 61
4. 34 48 56 36 49 59
5. 44 57 73 65 88 127
|
64b-8t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 14.30 9.61
2. 15.54 10.44
3. 34 66 82 34 52 69
4. 29 37 46 27 34 41
5. 37 47 57 48 94 210
|
1518b-2t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 27 70 27 48 72
4. 45 74 116 35 49 59
5. 51 60 64 52 62 68
|
1518b-4t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 24 57 77 21 53 79
4. 35 54 69 33 50 73
5. 51 60 69 41 55 61
|
9000b-2t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 44 90 36 39 86
4. 58 218 240 68 301 316
5. 174 307 333 231 344 352
|
imix-2t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 5.20 15.54
2. 5.27 15.76
|
imix-4t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 8.36 24.99
2. 9.27 27.71
|
imix-8t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 13.01 38.91
2. 13.48 40.30
|
25ge2p1xxv710-eth-l2bdbasemaclrn-ndrpdr
RFC2544: Pkt throughput L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 18.63 12.52
2. 19.68 13.23
3. 29 48 69 22 46 70
4. 32 39 45 32 40 48
5. 61 71 81 61 71 80
|
64b-4t2c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 36.57 24.58
2. 37.31 25.07
3. 23 40 59 28 45 58
4. 27 32 37 27 31 35
5. 52 57 63 52 59 66
|
64b-8t4c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 35.08 23.58
2. 35.62 23.93
3. 29 47 63 27 45 55
4. 23 26 30 22 26 29
5. 31 35 39 30 34 39
|
1518b-2t1c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 21 48 70 20 67 83
4. 31 49 69 42 67 88
5. 38 51 57 38 49 59
|
1518b-4t2c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 38 73 20 50 80
4. 32 53 68 34 52 81
5. 45 53 57 44 56 63
|
9000b-2t1c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 36 39 58 36 52 82
4. 43 231 255 55 129 139
5. 194 272 295 101 180 187
|
imix-2t1c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-4t2c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-8t4c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 10.16 6.83
2. 10.57 7.10
3. 27 54 68 33 54 77
4. 32 40 51 30 39 46
5. 52 61 71 51 62 72
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 18.95 12.73
2. 19.33 12.99
3. 27 43 56 28 50 68
4. 28 34 42 27 33 38
5. 39 45 51 47 63 73
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 33.00 22.18
2. 34.60 23.25
3. 22 42 56 28 38 49
4. 25 29 32 26 30 34
5. 38 45 52 37 53 63
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 30 68 21 42 74
4. 33 60 93 34 51 63
5. 45 55 64 40 53 61
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 46 76 20 38 47
4. 34 52 63 33 50 67
5. 44 63 72 46 53 60
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 39 72 35 44 56
4. 52 270 283 50 268 338
5. 187 306 319 217 306 332
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 10.16 30.37
2. 10.60 31.71
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.38 49.00
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 9.18 6.17
2. 9.46 6.36
3. 27 55 77 31 47 58
4. 32 43 53 32 42 49
5. 58 69 78 52 64 75
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 18.00 12.09
2. 18.36 12.34
3. 34 51 68 32 50 69
4. 27 33 37 29 36 46
5. 53 62 71 50 60 70
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 33.03 22.19
2. 35.22 23.67
3. 29 42 56 26 47 58
4. 28 32 36 27 31 35
5. 57 69 79 54 65 77
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 3.89 47.81
2. 3.93 48.29
3. 20 46 76 20 33 52
4. 34 54 77 33 48 70
5. 46 60 63 47 55 60
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 21 45 66 25 53 83
4. 33 54 76 39 59 78
5. 50 67 79 47 76 82
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 49 88 36 67 94
4. 65 208 226 65 112 140
5. 141 249 260 133 239 249
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 8.57 25.64
2. 8.89 26.60
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 14.75 44.13
2. 16.32 48.82
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 9.94 6.68
2. 10.35 6.96
3. 28 53 74 29 57 78
4. 29 38 47 31 42 48
5. 55 65 74 54 65 76
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 19.83 13.33
2. 20.43 13.73
3. 29 47 70 28 48 69
4. 27 33 41 28 34 40
5. 50 59 67 51 61 70
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 32.90 22.11
2. 34.33 23.07
3. 27 46 59 31 47 61
4. 26 29 32 26 29 32
5. 37 42 46 38 43 49
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 21 48 71 24 71 78
4. 34 57 91 33 55 80
5. 44 52 59 42 52 58
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 21 43 60 21 53 78
4. 33 48 66 39 55 69
5. 45 56 65 48 58 68
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 41 93 36 60 90
4. 39 230 252 49 147 155
5. 123 214 239 107 172 184
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 10.04 30.03
2. 10.31 30.82
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 8.72 5.86
2. 9.26 6.22
3. 22 44 68 29 52 70
4. 32 47 59 36 44 52
5. 63 76 88 61 74 83
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 14.38 9.66
2. 15.54 10.44
3. 27 53 83 34 45 69
4. 28 36 44 28 34 40
5. 50 71 99 46 65 77
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 20.86 14.02
2. 22.85 15.35
3. 17 32 36 38 52 58
4. 26 31 36 26 31 37
5. 36 47 57 35 49 63
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 21 42 73 20 46 79
4. 35 53 81 37 52 72
5. 43 56 62 49 60 68
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 21 48 78 25 65 80
4. 35 54 81 33 53 68
5. 49 68 77 45 63 73
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 37 53 84 36 52 85
4. 50 139 163 70 269 289
5. 184 273 305 196 326 336
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 8.70 26.02
2. 9.27 27.71
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 14.67 43.88
2. 14.90 44.55
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 8.63 5.80
2. 9.17 6.16
3. 28 49 76 24 49 70
4. 27 35 42 34 42 48
5. 60 72 81 62 77 87
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 14.79 9.94
2. 16.43 11.04
3. 28 49 64 30 52 68
4. 29 35 43 27 34 39
5. 62 105 164 74 163 223
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 22.09 14.84
2. 23.46 15.76
3. 42 71 81 29 40 61
4. 28 33 40 26 31 35
5. 43 59 77 40 58 79
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 22 53 74 21 49 65
4. 35 54 78 37 54 85
5. 46 59 70 45 55 60
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 21 42 66 25 68 88
4. 33 48 73 34 58 73
5. 49 63 74 44 58 68
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 38 61 36 64 93
4. 50 142 159 55 155 163
5. 129 227 248 189 297 310
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 8.61 25.75
2. 9.20 27.52
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 14.24 42.58
2. 15.05 45.00
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 8.66 5.82
2. 9.19 6.18
3. 29 50 72 28 58 77
4. 35 42 46 29 37 45
5. 63 75 87 62 76 86
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 14.36 9.65
2. 16.17 10.87
3. 30 56 72 30 48 71
4. 29 36 45 28 35 43
5. 64 130 188 76 172 231
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 21.71 14.59
2. 23.06 15.50
3. 22 26 49 25 37 49
4. 27 33 42 27 32 37
5. 42 60 81 39 51 65
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 39 69 20 40 75
4. 39 61 89 38 56 67
5. 41 54 61 45 59 69
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 21 53 81 24 70 81
4. 33 46 59 33 49 62
5. 43 53 58 42 52 59
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 50 65 37 75 93
4. 58 176 187 70 120 141
5. 179 250 278 122 218 284
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 8.62 25.79
2. 8.98 26.85
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 14.60 43.66
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 10.21 6.86
2. 10.63 7.14
3. 19 45 79 17 46 77
4. 33 46 56 34 47 56
5. 56 68 78 52 63 73
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 18.98 12.76
2. 19.30 12.97
3. 28 48 65 29 48 65
4. 27 33 41 28 34 40
5. 40 46 52 47 63 73
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 33.06 22.22
2. 34.41 23.13
3. 24 49 60 36 55 73
4. 25 29 32 26 30 34
5. 37 44 50 37 51 60
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 38 77 20 53 76
4. 39 59 96 44 77 111
5. 49 59 65 48 76 81
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 52 71 20 43 73
4. 36 57 82 42 66 88
5. 49 58 66 50 71 76
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 49 80 36 87 136
4. 47 124 136 76 290 309
5. 163 289 303 229 307 315
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 10.16 30.37
2. 10.65 31.84
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.38 49.00
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 9.21 6.19
2. 9.45 6.35
3. 23 51 79 17 40 57
4. 46 62 72 26 39 51
5. 59 71 81 54 68 78
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 17.93 12.05
2. 18.38 12.35
3. 26 46 75 22 55 76
4. 24 28 35 30 38 43
5. 53 63 72 50 60 69
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 33.17 22.29
2. 35.22 23.67
3. 25 40 52 30 49 59
4. 28 32 37 27 30 33
5. 53 61 70 52 62 71
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 3.90 47.97
2. 3.92 48.21
3. 20 39 70 20 44 68
4. 39 56 78 33 52 81
5. 51 58 64 46 62 70
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 3.90 47.93
2. 3.92 48.17
3. 21 51 80 20 42 59
4. 36 49 62 36 57 88
5. 47 63 69 49 64 76
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 37 60 74 36 54 76
4. 64 162 186 50 123 143
5. 171 251 261 142 221 233
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 8.55 25.56
2. 8.94 26.75
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 10.19 6.85
2. 10.40 6.99
3. 20 51 69 17 44 71
4. 33 42 56 36 50 59
5. 59 70 80 59 72 80
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 20.09 13.50
2. 20.39 13.70
3. 26 50 67 31 51 69
4. 27 33 39 28 34 42
5. 50 58 66 53 62 71
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 32.99 22.17
2. 34.17 22.96
3. 27 36 47 33 54 69
4. 26 29 33 26 29 33
5. 38 42 47 37 42 47
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 39 53 20 42 74
4. 39 73 96 50 75 104
5. 44 54 58 47 56 61
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 39 76 20 32 42
4. 37 55 69 45 69 85
5. 49 60 68 53 64 70
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 37 58 89 36 51 85
4. 45 154 178 48 222 239
5. 120 169 190 238 277 287
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 10.15 30.34
2. 10.31 30.83
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 8.65 5.82
2. 9.28 6.24
3. 27 51 75 17 43 77
4. 39 49 55 32 40 45
5. 64 78 92 58 74 82
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 14.28 9.59
2. 15.35 10.32
3. 23 41 49 22 49 79
4. 32 40 52 27 33 38
5. 51 80 139 44 62 73
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 20.84 14.00
2. 21.61 14.52
3. 27 51 66 29 50 71
4. 28 33 42 26 34 41
5. 34 42 50 34 46 58
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 30 71 20 43 70
4. 36 54 68 41 66 87
5. 46 56 63 48 63 70
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 21 39 72 20 39 70
4. 34 62 91 36 69 105
5. 46 64 73 40 48 52
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 71 105 36 76 93
4. 59 278 317 40 298 335
5. 199 317 327 240 352 357
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 8.71 26.05
2. 9.14 27.33
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 14.38 43.01
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 8.71 5.85
2. 8.98 6.03
3. 18 45 66 17 47 62
4. 28 44 50 43 56 66
5. 52 64 75 55 68 78
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 14.97 10.06
2. 16.47 11.07
3. 25 44 74 25 42 69
4. 30 37 44 30 38 45
5. 67 116 169 62 113 167
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 21.84 14.68
2. 22.96 15.43
3. 23 34 51 19 40 47
4. 26 31 36 25 31 43
5. 44 61 81 39 50 62
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 39 70 20 53 64
4. 40 59 77 46 80 110
5. 57 76 83 56 67 75
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 35 51 22 48 59
4. 34 55 68 36 53 70
5. 47 65 76 49 65 72
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 55 88 36 39 86
4. 59 316 341 77 295 313
5. 187 308 320 264 363 373
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 8.69 25.98
2. 9.16 27.40
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 14.45 43.23
2. 15.27 45.68
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 8.60 5.78
2. 9.18 6.17
3. 21 47 73 17 43 69
4. 40 49 55 25 34 51
5. 61 73 82 57 73 83
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 13.84 9.30
2. 15.67 10.53
3. 33 64 80 21 50 77
4. 31 40 47 28 37 42
5. 52 81 155 57 115 175
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 21.95 14.75
2. 23.08 15.51
3. 21 24 63 42 58 66
4. 26 32 38 26 31 36
5. 43 58 77 40 53 69
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 29 44 20 49 72
4. 34 56 87 33 49 73
5. 46 53 60 43 52 64
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 28 48 20 40 50
4. 32 49 64 40 65 84
5. 46 56 60 46 56 65
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 52 63 36 60 68
4. 56 161 197 41 249 269
5. 163 317 332 124 249 262
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 8.65 25.86
2. 9.12 27.27
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 14.60 43.66
2. 16.32 48.82
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 10.16 6.83
2. 10.63 7.14
3. 17 46 78 17 41 68
4. 33 41 51 35 47 57
5. 58 71 81 55 69 77
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 18.91 12.71
2. 19.26 12.94
3. 25 48 73 27 50 75
4. 28 36 42 27 35 41
5. 40 46 52 48 65 76
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 33.00 22.18
2. 34.79 23.38
3. 25 49 61 25 33 41
4. 25 29 34 25 29 34
5. 38 45 52 37 54 63
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 21 39 64 20 41 76
4. 39 60 71 42 65 84
5. 41 51 54 52 69 78
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 24 51 82 24 52 71
4. 33 54 71 39 60 84
5. 48 56 64 45 62 66
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 51 63 36 64 96
4. 59 199 257 61 182 207
5. 148 213 224 106 167 188
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 10.23 30.59
2. 10.62 31.77
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.32 48.82
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 9.15 6.15
2. 9.43 6.34
3. 23 57 72 17 46 72
4. 34 51 57 27 38 45
5. 58 71 81 53 67 79
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 17.83 11.98
2. 18.38 12.35
3. 31 51 75 31 56 69
4. 26 30 35 29 36 42
5. 53 62 71 49 59 69
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 33.22 22.32
2. 34.92 23.47
3. 27 51 63 27 47 63
4. 27 30 33 27 30 33
5. 54 66 77 52 63 73
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 3.90 48.02
2. 3.92 48.26
3. 20 29 46 20 43 75
4. 44 59 75 45 70 90
5. 51 59 61 44 57 66
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 3.90 47.93
2. 3.91 48.17
3. 21 45 67 20 44 73
4. 35 54 81 40 60 81
5. 50 58 66 47 60 67
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 49 55 37 60 77
4. 56 140 198 59 105 140
5. 123 187 203 131 218 231
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 8.60 25.73
2. 8.92 26.66
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 14.78 44.20
2. 16.32 48.81
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 10.02 6.74
2. 10.38 6.98
3. 22 51 69 22 47 70
4. 36 49 62 28 35 41
5. 60 72 82 53 65 75
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 20.03 13.46
2. 20.44 13.73
3. 28 46 67 26 48 73
4. 27 32 37 27 33 39
5. 52 61 69 53 63 73
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 32.99 22.17
2. 34.86 23.42
3. 26 51 59 27 40 48
4. 25 29 32 25 29 31
5. 39 44 49 39 44 50
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 32 49 20 52 70
4. 36 54 68 37 56 79
5. 47 57 62 41 60 67
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 21 59 78 23 51 71
4. 37 56 66 34 48 64
5. 44 57 62 43 55 62
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 37 41 51 36 95 143
4. 69 170 184 40 309 344
5. 135 196 216 225 354 369
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 10.18 30.44
2. 10.29 30.77
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 8.63 5.80
2. 9.30 6.25
3. 22 46 69 19 47 74
4. 36 44 50 25 33 37
5. 66 82 97 67 81 93
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 14.51 9.75
2. 15.46 10.39
3. 22 41 65 24 46 75
4. 29 34 40 29 39 46
5. 51 71 101 45 63 74
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 22.31 14.99
2. 22.81 15.33
3. 22 35 45 38 51 66
4. 26 31 37 25 30 37
5. 36 47 59 34 48 61
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 25 49 20 30 47
4. 38 56 75 39 61 82
5. 52 74 79 44 55 60
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 21 48 82 21 62 82
4. 34 48 60 44 74 106
5. 52 66 75 54 71 79
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 61 76 36 78 110
4. 46 144 197 45 161 205
5. 163 263 277 150 312 318
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 8.65 25.87
2. 9.10 27.22
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 14.67 43.88
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 8.66 5.82
2. 8.97 6.03
3. 23 50 67 17 44 74
4. 35 45 50 31 50 62
5. 56 68 79 54 69 80
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 14.84 9.98
2. 16.58 11.14
3. 21 56 74 26 49 74
4. 32 41 50 28 34 40
5. 71 137 193 75 148 199
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 22.27 14.96
2. 23.53 15.81
3. 38 56 64 38 49 57
4. 29 33 41 25 32 37
5. 43 61 81 38 51 66
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 40 75 20 42 61
4. 33 56 74 36 55 77
5. 43 51 57 48 57 66
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 21 38 61 20 48 75
4. 32 49 60 36 54 76
5. 50 60 68 50 62 70
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 37 42 61 36 70 81
4. 54 83 123 43 170 180
5. 157 244 274 147 224 236
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 8.68 25.96
2. 9.15 27.37
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 14.75 44.10
2. 16.38 49.00
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 8.65 5.81
2. 9.00 6.05
3. 17 48 75 17 40 73
4. 35 45 51 27 37 49
5. 59 71 82 55 70 79
|
64b-4t2c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 14.35 9.64
2. 15.86 10.66
3. 28 52 72 20 46 73
4. 26 32 38 28 35 42
5. 53 76 104 52 87 151
|
64b-8t4c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 22.13 14.87
2. 23.38 15.71
3. 44 68 79 17 30 42
4. 28 35 41 26 32 37
5. 44 57 72 43 60 81
|
1518b-2t1c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 3.90 48.00
2. 3.92 48.24
3. 21 47 74 21 52 83
4. 34 50 75 41 64 82
5. 50 61 67 48 60 68
|
1518b-4t2c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 21 32 67 20 39 69
4. 37 54 73 39 59 75
5. 54 65 73 46 68 75
|
9000b-2t1c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 0.66 47.79
2. 0.67 48.27
3. 37 55 100 36 40 56
4. 46 229 258 67 192 199
5. 211 273 300 167 326 337
|
imix-2t1c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 8.70 26.03
2. 9.13 27.31
|
imix-4t2c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 14.60 43.66
2. 16.30 48.76
|
imix-8t4c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 14.82 44.33
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdscale100kmaclrn-ndrpdr
RFC2544: Pkt throughput for L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 50k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 13.12 8.82
2. 14.36 9.65
3. 30 48 74 35 54 72
4. 32 41 48 30 38 46
5. 63 74 85 60 70 81
|
64b-4t2c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 26.71 17.95
2. 28.66 19.26
3. 28 42 53 29 43 58
4. 28 33 38 28 33 37
5. 53 61 69 66 80 92
|
64b-8t4c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 35.99 24.18
2. 36.49 24.52
3. 28 46 61 26 46 60
4. 24 28 31 24 27 30
5. 31 35 41 30 34 41
|
1518b-2t1c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 36 66 20 44 76
4. 36 56 72 39 63 84
5. 44 71 76 38 51 60
|
1518b-4t2c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 43 75 20 34 61
4. 33 51 75 52 83 105
5. 45 58 65 57 70 78
|
9000b-2t1c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 37 54 90 35 39 74
4. 42 233 243 57 285 304
5. 183 308 319 270 369 381
|
imix-2t1c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 12.84 38.41
2. 13.90 41.58
|
imix-4t2c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-8t4c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdscale10kmaclrn-ndrpdr
RFC2544: Pkt throughput for L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 5k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 13.81 9.28
2. 15.50 10.41
3. 28 44 50 30 45 60
4. 34 46 53 31 40 47
5. 61 70 79 53 61 69
|
64b-4t2c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 29.96 20.14
2. 31.03 20.85
3. 26 43 57 26 37 50
4. 26 30 34 26 31 35
5. 58 67 75 55 63 70
|
64b-8t4c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 35.51 23.86
2. 36.05 24.22
3. 25 42 51 27 40 49
4. 23 27 30 24 27 31
5. 29 33 36 29 32 36
|
1518b-2t1c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 20 28 45 20 44 72
4. 30 50 68 32 48 61
5. 41 50 57 43 58 68
|
1518b-4t2c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 24 49 68 20 48 66
4. 34 49 59 39 63 78
5. 46 56 65 40 59 66
|
9000b-2t1c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 0.66 47.55
2. 0.67 48.27
3. 36 38 59 35 38 57
4. 52 165 197 52 187 279
5. 163 256 290 206 311 353
|
imix-2t1c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-4t2c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-8t4c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2bdscale1mmaclrn-ndrpdr
RFC2544: Pkt throughput for L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 500k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 10.58 7.11
2. 13.13 8.82
3. 19 49 81 33 56 78
4. 32 43 52 33 42 50
5. 64 85 105 59 71 82
|
64b-4t2c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 21.78 14.63
2. 25.82 17.35
3. 29 44 55 29 45 61
4. 29 36 42 28 34 39
5. 64 81 102 52 62 71
|
64b-8t4c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 36.57 24.57
2. 37.08 24.92
3. 30 43 52 25 39 54
4. 28 32 37 25 30 33
5. 37 42 48 34 39 46
|
1518b-2t1c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 20 44 69 20 49 80
4. 34 68 108 32 55 76
5. 38 53 59 41 53 61
|
1518b-4t2c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 3.86 47.55
2. 3.92 48.27
3. 20 38 71 21 71 83
4. 33 49 63 33 52 81
5. 45 55 60 40 52 59
|
9000b-2t1c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 0.66 47.31
2. 0.67 48.27
3. 37 45 75 35 69 107
4. 40 229 249 39 333 349
5. 139 229 241 270 373 382
|
imix-2t1c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 10.16 30.38
2. 11.50 34.40
|
imix-4t2c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-8t4c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2patch-ndrpdr
RFC2544: Pkt throughput L2patch test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 patch DUT1 and DUT2 tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header,IPv4 header with static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-l2patch-ndrpdr
|
1. 35.96 24.16
2. 36.50 24.53
3. 23 43 57 24 52 68
4. 22 26 29 22 25 28
5. 42 47 52 43 48 53
|
64b-4t2c-eth-l2patch-ndrpdr
|
1. 35.48 23.84
2. 36.02 24.20
3. 24 42 50 23 42 52
4. 22 30 31 21 29 31
5. 26 31 35 26 30 33
|
64b-8t4c-eth-l2patch-ndrpdr
|
1. 31.07 20.88
2. 31.72 21.32
3. 22 42 50 28 51 67
4. 20 26 30 20 28 31
5. 23 27 30 23 26 30
|
1518b-2t1c-eth-l2patch-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 19 39 78 18 24 40
4. 27 40 57 31 50 70
5. 38 47 54 41 52 57
|
1518b-4t2c-eth-l2patch-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 18 40 66 21 58 74
4. 29 46 58 30 47 57
5. 46 58 68 42 61 69
|
9000b-2t1c-eth-l2patch-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 35 52 83 34 47 97
4. 56 330 350 38 319 333
5. 229 299 311 224 338 344
|
imix-2t1c-eth-l2patch-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-4t2c-eth-l2patch-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-8t4c-eth-l2patch-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
25ge2p1xxv710-eth-l2xcbase-ndrpdr
RFC2544: Pkt throughput L2XC test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with Intel-XXV710.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-2t1c-eth-l2xcbase-ndrpdr
|
1. 26.53 17.83
2. 27.06 18.19
3. 25 50 67 27 52 72
4. 26 30 33 29 35 42
5. 50 56 62 50 57 63
|
64b-4t2c-eth-l2xcbase-ndrpdr
|
1. 36.89 24.79
2. 37.07 24.91
3. 24 36 49 25 38 47
4. 24 27 31 22 26 30
5. 29 33 37 29 32 37
|
64b-8t4c-eth-l2xcbase-ndrpdr
|
1. 32.57 21.89
2. 33.84 22.74
3. 25 45 61 24 45 60
4. 22 29 32 21 25 30
5. 76 107 124 63 89 115
|
1518b-2t1c-eth-l2xcbase-ndrpdr
|
1. 3.90 48.03
2. 3.92 48.27
3. 19 27 45 19 44 68
4. 36 55 70 38 74 95
5. 45 64 74 42 65 74
|
1518b-4t2c-eth-l2xcbase-ndrpdr
|
1. 3.88 47.79
2. 3.92 48.27
3. 19 29 56 19 44 74
4. 32 46 57 35 61 82
5. 50 74 80 44 55 59
|
9000b-2t1c-eth-l2xcbase-ndrpdr
|
1. 0.67 48.03
2. 0.67 48.27
3. 36 76 111 35 51 72
4. 58 259 308 63 189 197
5. 200 319 329 173 241 281
|
imix-2t1c-eth-l2xcbase-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-4t2c-eth-l2xcbase-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|
imix-8t4c-eth-l2xcbase-ndrpdr
|
1. 16.30 48.76
2. 16.30 48.76
|