2n-clx-xxv710

2n1l-25ge2p1xxv710-avf-dot1q-ip6base-mrr

RFC2544: Pkt throughput IPv6 routing with IEEE 802.1Q test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing. IEEE 802.1Q tagging is applied on link between DUT1-if2 and TG-if2.

  • [Cfg] DUT configuration: DUT1 is configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG veriffication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 78b-2t1c-avf-dot1q-ip6base-mrr 

 [15.31, 15.71, 15.39, 15.51, 15.23, 15.98, 15.37, 15.48, 15.34, 15.41] 

 78b-4t2c-avf-dot1q-ip6base-mrr 

 [31.29, 30.54, 30.55, 30.68, 30.66, 31.14, 30.46, 30.71, 30.58, 30.36] 

 78b-8t4c-avf-dot1q-ip6base-mrr 

 [36.14, 36.09, 36.12, 35.89, 35.92, 37.02, 35.98, 36.13, 35.94, 37.25]

2n1l-25ge2p1xxv710-avf-ethip6-ip6base-mrr

Packet throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 tested with Intel-XXV710.

  • [Ver] TG veriffication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 78b-2t1c-avf- 
 ethip6-ip6base-mrr 

 [18.99, 19.09, 18.91, 18.94, 19.21, 19.09, 19.17, 19.01, 18.87, 19.29] 

 78b-4t2c-avf- 
 ethip6-ip6base-mrr 

 [36.77, 36.87, 37.03, 36.93, 36.78, 36.79, 36.75, 37.02, 37.04, 37.07] 

 78b-8t4c-avf- 
 ethip6-ip6base-mrr 

 [35.42, 35.18, 35.65, 35.75, 35.78, 36.09, 35.30, 35.57, 35.74, 35.51]

2n1l-25ge2p1xxv710-avf-ethip6-ip6scale200k-mrr

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv6 routing and 2x100k static IPv6 /64 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG veriffication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 78b-2t1c-avf- 
 ethip6-ip6scale200k-mrr 

 [12.21, 12.87, 13.43, 12.68, 12.84, 13.61, 12.75, 12.71, 12.70, 12.91] 

 78b-4t2c-avf- 
 ethip6-ip6scale200k-mrr 

 [22.63, 23.46, 22.98, 22.89, 23.10, 23.11, 23.78, 23.38, 23.67, 24.30] 

 78b-8t4c-avf- 
 ethip6-ip6scale200k-mrr 

 [37.49, 37.50, 37.38, 37.26, 37.50, 37.28, 37.22, 37.33, 37.24, 37.24]

2n1l-25ge2p1xxv710-avf-ethip6-ip6scale20k-mrr

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv6 routing and 2x10k static IPv6 /64 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG veriffication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 78b-2t1c-avf- 
 ethip6-ip6scale20k-mrr 

 [15.53, 15.88, 15.60, 15.68, 16.00, 15.75, 15.60, 16.37, 16.03, 15.69] 

 78b-4t2c-avf- 
 ethip6-ip6scale20k-mrr 

 [31.20, 30.25, 31.15, 31.17, 30.58, 31.12, 30.65, 30.49, 32.40, 30.86] 

 78b-8t4c-avf- 
 ethip6-ip6scale20k-mrr 

 [36.33, 36.02, 36.07, 37.48, 36.78, 37.05, 36.82, 36.09, 36.54, 36.52]

2n1l-25ge2p1xxv710-avf-ethip6-ip6scale2m-mrr

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv6 routing and 2x1M static IPv6 /64 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG veriffication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 78b-2t1c-avf- 
 ethip6-ip6scale2m-mrr 

 [9.58, 9.73, 10.05, 9.94, 10.03, 9.91, 9.82, 10.47, 9.87, 9.95] 

 78b-4t2c-avf- 
 ethip6-ip6scale2m-mrr 

 [18.15, 18.23, 18.47, 18.65, 18.56, 19.28, 18.36, 19.38, 18.75, 18.32] 

 78b-8t4c-avf- 
 ethip6-ip6scale2m-mrr 

 [35.72, 35.51, 35.45, 35.89, 35.62, 35.82, 36.35, 35.50, 35.71, 35.70]

2n1l-25ge2p1xxv710-dot1q-ip6base-mrr

RFC2544: Pkt throughput IPv6 routing with IEEE 802.1Q test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing. IEEE 802.1Q tagging is applied on link between DUT1-if2 and TG-if2.

  • [Cfg] DUT configuration: DUT1 is configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG veriffication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 78b-2t1c-dot1q-ip6base-mrr 

 [12.88, 13.23, 13.66, 13.06, 12.94, 12.94, 13.19, 12.91, 13.08, 12.93] 

 78b-4t2c-dot1q-ip6base-mrr 

 [25.13, 24.96, 24.90, 24.95, 25.27, 25.04, 25.07, 24.98, 25.13, 25.23] 

 78b-8t4c-dot1q-ip6base-mrr 

 [37.36, 37.08, 36.96, 37.07, 36.94, 36.99, 37.00, 37.20, 36.86, 37.01]

2n1l-25ge2p1xxv710-ethip6-ip6base-mrr

Packet throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 tested with Intel-XXV710.

  • [Ver] TG veriffication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 78b-2t1c-ethip6-ip6base-mrr 

 [15.34, 15.91, 15.21, 15.78, 15.65, 15.15, 15.28, 15.27, 15.19, 15.45] 

 78b-4t2c-ethip6-ip6base-mrr 

 [30.91, 30.51, 30.31, 30.85, 31.65, 30.41, 30.41, 30.23, 30.93, 31.13] 

 78b-8t4c-ethip6-ip6base-mrr 

 [36.91, 36.24, 36.24, 36.60, 36.69, 36.24, 36.24, 36.37, 36.39, 36.22]

2n1l-25ge2p1xxv710-ethip6-ip6scale200k-mrr

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv6 routing and 2x100k static IPv6 /64 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG veriffication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 78b-2t1c- 
 ethip6-ip6scale200k-mrr 

 [11.13, 10.97, 10.86, 10.84, 10.84, 11.94, 10.82, 11.57, 11.54, 11.03] 

 78b-4t2c- 
 ethip6-ip6scale200k-mrr 

 [18.88, 20.03, 19.02, 19.12, 19.84, 19.16, 20.01, 19.09, 19.68, 19.17] 

 78b-8t4c- 
 ethip6-ip6scale200k-mrr 

 [36.24, 34.82, 33.57, 33.73, 33.69, 33.52, 34.07, 34.23, 33.67, 33.57]

2n1l-25ge2p1xxv710-ethip6-ip6scale20k-mrr

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv6 routing and 2x10k static IPv6 /64 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG veriffication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 78b-2t1c- 
 ethip6-ip6scale20k-mrr 

 [13.01, 12.89, 12.96, 13.78, 13.14, 13.52, 13.14, 12.90, 12.97, 13.11] 

 78b-4t2c- 
 ethip6-ip6scale20k-mrr 

 [26.94, 25.89, 25.82, 25.73, 25.92, 25.73, 25.47, 25.78, 25.26, 25.43] 

 78b-8t4c- 
 ethip6-ip6scale20k-mrr 

 [37.15, 37.05, 37.11, 37.50, 37.13, 37.50, 37.11, 37.10, 37.49, 36.87]

2n1l-25ge2p1xxv710-ethip6-ip6scale2m-mrr

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.

  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.

  • [Cfg] DUT configuration: DUT1 is configured with IPv6 routing and 2x1M static IPv6 /64 route entries. DUT1 is tested with Intel-XXV710.

  • [Ver] TG veriffication: In MaxReceivedRate tests TG sends traffic at line rate and reports total received packets over trial period. Test packets are generated by TG on links to DUT1. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.

  • [Ref] Applicable standard specifications: RFC2544.

 Test Name 

 Maximum Receive Rate trial [Mpps] 

 78b-2t1c-ethip6-ip6scale2m-mrr 

 [8.91, 8.64, 9.23, 8.76, 8.79, 9.16, 9.11, 8.74, 9.26, 8.70] 

 78b-4t2c-ethip6-ip6scale2m-mrr 

 [16.05, 16.82, 16.12, 16.90, 16.23, 16.24, 16.37, 16.27, 16.60, 16.31] 

 78b-8t4c-ethip6-ip6scale2m-mrr 

 [29.86, 30.05, 30.36, 30.19, 30.18, 30.28, 30.29, 30.52, 30.31, 30.53]