3n-hsw-vic1385
40ge2p1vic1385-dot1q-l2bdbasemaclrn-ndrpdr
RFC2544: Pkt throughput L2BD with IEEE 802.1Q test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge domain and MAC learning enabled. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 5.59 3.76
2. 8.35 5.61
3. 10 46 54 10 39 56
4. 32 41 46 37 45 51
5. 80 99 114 84 105 119
|
64b-2t2c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 12.64 8.49
2. 16.89 11.35
3. 11 22 37 10 24 40
4. 29 43 51 28 41 50
5. 51 61 69 49 59 67
|
64b-4t4c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 28.55 19.18
2. 31.08 20.89
3. 10 16 21 10 16 21
4. 19 26 31 17 23 28
5. 36 41 46 36 41 47
|
1518b-1t1c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 1.39 17.07
2. 3.08 37.95
3. 12 25 31 12 24 32
4. 22 37 46 16 38 47
5. 38 49 57 39 50 60
|
1518b-2t2c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 2.90 35.72
2. 3.08 37.93
3. 12 20 28 12 18 25
4. 14 31 41 15 32 45
5. 29 41 49 28 41 48
|
1518b-4t4c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 2.95 36.30
2. 3.13 38.54
3. 12 19 26 11 15 25
4. 13 29 34 12 29 34
5. 20 36 40 25 34 38
|
imix-1t1c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 0.68 2.03
2. 6.84 20.46
|
imix-2t2c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 1.34 3.99
2. 11.71 35.01
|
imix-4t4c-
dot1q-l2bdbasemaclrn-ndrpdr
|
1. 8.79 26.29
2. 12.18 36.43
|
40ge2p1vic1385-dot1q-l2xcbase-ndrpdr
RFC2544: Pkt throughput L2XC with IEEE 802.1Q test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-dot1q-l2xcbase-ndrpdr
|
1. 8.47 5.69
2. 10.51 7.06
3. 10 24 33 10 29 39
4. 25 40 53 26 40 50
5. 67 86 99 72 91 106
|
64b-2t2c-dot1q-l2xcbase-ndrpdr
|
1. 14.43 9.70
2. 21.42 14.39
3. 10 18 25 10 22 29
4. 17 23 29 16 25 31
5. 37 42 48 33 39 45
|
64b-4t4c-dot1q-l2xcbase-ndrpdr
|
1. 28.60 19.22
2. 31.30 21.03
3. 10 13 15 9 12 15
4. 14 18 21 14 17 21
5. 20 23 28 21 24 28
|
1518b-1t1c-
dot1q-l2xcbase-ndrpdr
|
1. 2.76 33.94
2. 3.10 38.08
3. 11 18 31 11 14 27
4. 14 41 49 14 42 50
5. 33 44 50 33 44 52
|
1518b-2t2c-
dot1q-l2xcbase-ndrpdr
|
1. 2.79 34.38
2. 3.09 38.00
3. 11 14 16 11 12 16
4. 14 32 47 12 36 45
5. 27 36 44 25 34 42
|
1518b-4t4c-
dot1q-l2xcbase-ndrpdr
|
1. 3.02 37.21
2. 3.13 38.53
3. 12 14 18 11 12 16
4. 14 30 36 12 32 36
5. 27 40 46 27 38 45
|
imix-1t1c-
dot1q-l2xcbase-ndrpdr
|
1. 0.37 1.11
2. 8.48 25.35
|
imix-2t2c-
dot1q-l2xcbase-ndrpdr
|
1. 1.60 4.80
2. 11.53 34.47
|
imix-4t4c-
dot1q-l2xcbase-ndrpdr
|
1. 8.56 25.60
2. 12.14 36.31
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 5.28 3.55
2. 5.40 3.63
3. 10 40 55 10 54 74
4. 40 72 100 13 57 91
5. 59 89 107 59 84 94
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 10.34 6.95
2. 10.64 7.15
3. 10 15 21 10 18 25
4. 22 46 56 18 44 52
5. 36 45 52 36 46 52
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 16.78 11.28
2. 18.33 12.31
3. 10 18 28 10 20 30
4. 20 31 36 20 30 34
5. 38 52 75 35 48 73
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 3.11 38.27
2. 3.13 38.46
3. 12 34 42 12 30 41
4. 12 52 61 13 53 65
5. 42 53 60 44 58 67
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 2.92 35.95
2. 3.09 37.99
3. 12 18 25 12 12 20
4. 13 48 57 16 47 60
5. 30 47 59 29 47 60
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 2.78 34.21
2. 3.15 38.76
3. 12 15 21 12 15 19
4. 13 36 42 12 37 43
5. 30 39 42 29 40 45
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 5.35 16.00
2. 5.41 16.17
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 9.30 27.80
2. 10.67 31.91
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl10sf-100flows-ndrpdr
|
1. 8.99 26.88
2. 12.26 36.66
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 5.34 3.59
2. 5.39 3.62
3. 10 38 55 10 52 72
4. 41 56 80 37 71 85
5. 55 74 91 55 74 87
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 10.11 6.79
2. 10.36 6.96
3. 10 34 44 10 34 42
4. 23 37 46 22 37 45
5. 41 52 59 43 54 61
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 17.39 11.69
2. 18.55 12.47
3. 10 13 19 10 13 19
4. 18 30 36 17 28 34
5. 36 51 95 33 45 74
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 3.11 38.27
2. 3.11 38.27
3. 12 21 37 12 15 36
4. 13 51 59 12 55 66
5. 41 53 60 44 58 71
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 2.84 34.97
2. 3.06 37.70
3. 12 21 29 12 16 27
4. 13 52 62 12 51 59
5. 34 46 54 39 53 63
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 2.78 34.24
2. 3.15 38.80
3. 12 13 28 12 13 25
4. 16 36 39 15 36 42
5. 31 39 42 30 41 47
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 5.35 16.01
2. 5.38 16.09
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 9.20 27.51
2. 10.70 31.99
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl10sf-100kflows-ndrpdr
|
1. 9.85 29.46
2. 12.22 36.55
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 5.35 3.59
2. 5.40 3.63
3. 10 17 24 10 17 22
4. 20 45 61 19 30 53
5. 60 82 98 57 80 91
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 10.37 6.97
2. 10.58 7.11
3. 10 23 36 10 28 37
4. 19 32 43 19 29 40
5. 45 59 66 43 57 65
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 16.42 11.03
2. 17.18 11.54
3. 11 16 23 10 12 18
4. 17 24 30 16 24 29
5. 30 45 74 27 35 42
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 3.11 38.25
2. 3.11 38.25
3. 12 22 37 12 16 36
4. 17 51 59 13 56 67
5. 41 54 61 43 58 70
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 3.06 37.65
2. 3.08 37.84
3. 12 23 30 12 17 27
4. 13 49 61 12 50 64
5. 34 50 58 32 50 63
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 2.79 34.31
2. 3.14 38.68
3. 12 15 20 12 12 18
4. 13 37 42 12 38 45
5. 30 39 43 30 40 45
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 5.33 15.95
2. 5.39 16.11
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 10.33 30.89
2. 10.64 31.81
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl10sf-10kflows-ndrpdr
|
1. 9.89 29.57
2. 12.24 36.61
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 5.34 3.59
2. 5.39 3.62
3. 10 17 25 10 18 30
4. 21 56 71 19 61 68
5. 52 74 89 51 71 84
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 10.24 6.88
2. 10.54 7.08
3. 10 15 25 10 15 26
4. 20 40 48 19 38 45
5. 37 48 56 39 48 56
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 17.29 11.62
2. 18.44 12.39
3. 11 15 31 10 16 29
4. 19 29 35 19 28 34
5. 35 46 62 35 48 78
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 3.10 38.08
2. 3.10 38.08
3. 12 18 38 12 15 35
4. 13 53 63 13 55 64
5. 41 52 59 48 60 73
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 3.03 37.31
2. 3.08 37.87
3. 12 15 29 12 12 27
4. 13 46 53 12 49 56
5. 32 50 61 31 50 63
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 3.03 37.31
2. 3.15 38.74
3. 12 16 27 12 12 25
4. 14 36 42 12 37 44
5. 32 39 43 32 41 46
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 5.35 16.00
2. 5.39 16.13
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 10.28 30.73
2. 10.62 31.77
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl10sl-100flows-ndrpdr
|
1. 9.04 27.03
2. 12.26 36.66
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 5.36 3.60
2. 5.39 3.62
3. 10 20 34 10 24 38
4. 33 55 79 26 48 75
5. 55 78 91 57 79 88
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 10.32 6.94
2. 10.56 7.09
3. 10 11 21 10 12 20
4. 18 39 48 16 37 45
5. 37 47 53 38 47 54
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 17.30 11.63
2. 18.01 12.10
3. 10 16 28 10 14 22
4. 16 23 29 16 22 28
5. 31 41 54 29 35 41
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 3.11 38.24
2. 3.11 38.24
3. 12 18 38 11 15 35
4. 13 55 64 13 55 71
5. 41 53 61 43 57 69
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 3.05 37.55
2. 3.08 37.92
3. 12 15 29 12 12 26
4. 13 50 63 12 51 61
5. 32 47 57 36 48 63
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 2.79 34.28
2. 3.16 38.85
3. 12 26 30 12 24 28
4. 13 36 41 12 36 42
5. 30 39 43 31 40 47
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 5.20 15.57
2. 5.25 15.69
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 10.21 30.54
2. 10.63 31.79
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl10sl-100kflows-ndrpdr
|
1. 9.92 29.67
2. 12.26 36.66
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 5.31 3.57
2. 5.39 3.62
3. 10 17 54 10 17 57
4. 24 40 55 24 42 58
5. 52 71 85 48 67 78
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 10.36 6.96
2. 10.67 7.17
3. 10 19 28 10 23 30
4. 16 40 48 15 37 44
5. 36 44 52 38 48 56
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 16.69 11.22
2. 17.39 11.68
3. 10 20 27 10 12 19
4. 18 25 30 18 25 31
5. 29 38 47 29 38 46
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 3.11 38.26
2. 3.13 38.45
3. 12 17 30 12 15 23
4. 18 47 54 19 49 57
5. 41 52 59 43 58 69
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 3.09 38.04
2. 3.09 38.04
3. 12 18 28 12 17 25
4. 13 32 42 15 33 55
5. 32 46 55 31 48 57
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 2.95 36.32
2. 3.15 38.79
3. 12 25 29 12 23 27
4. 13 36 41 12 38 44
5. 31 39 43 29 41 46
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 5.34 15.96
2. 5.39 16.12
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 10.28 30.74
2. 10.65 31.85
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl10sl-10kflows-ndrpdr
|
1. 9.88 29.55
2. 12.24 36.59
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 5.20 3.49
2. 5.25 3.53
3. 10 30 51 10 28 53
4. 20 49 61 14 50 69
5. 53 74 88 54 70 83
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 10.34 6.95
2. 10.62 7.14
3. 10 20 32 10 21 32
4. 17 26 35 17 26 33
5. 34 44 51 39 48 55
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 17.04 11.45
2. 18.95 12.74
3. 10 11 18 10 10 18
4. 17 27 33 16 24 29
5. 41 75 134 33 43 57
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 3.09 38.05
2. 3.11 38.24
3. 12 19 29 12 15 27
4. 18 45 56 18 46 56
5. 36 46 54 39 51 58
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 2.85 35.11
2. 3.06 37.70
3. 12 15 26 12 12 20
4. 13 41 47 12 40 53
5. 33 47 57 39 50 59
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 2.77 34.10
2. 3.16 38.83
3. 12 13 24 12 12 23
4. 13 35 39 13 35 42
5. 30 39 42 29 40 46
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 5.22 15.60
2. 5.24 15.68
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 9.41 28.13
2. 10.67 31.92
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl1sf-100flows-ndrpdr
|
1. 8.87 26.54
2. 12.25 36.64
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 5.13 3.45
2. 5.21 3.50
3. 10 40 74 10 50 74
4. 19 30 39 16 29 38
5. 50 71 87 50 69 83
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 10.38 6.97
2. 10.66 7.17
3. 10 16 26 10 17 24
4. 18 35 42 20 32 42
5. 33 42 49 38 47 55
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 16.97 11.40
2. 18.20 12.23
3. 10 15 21 10 16 22
4. 18 27 33 17 26 31
5. 39 57 98 33 40 48
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 3.08 37.93
2. 3.11 38.31
3. 12 18 40 12 15 38
4. 15 47 58 16 49 58
5. 42 52 60 43 54 61
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 2.86 35.21
2. 3.08 37.95
3. 12 15 20 12 12 18
4. 18 39 56 17 40 60
5. 33 44 59 37 49 61
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 2.75 33.81
2. 3.14 38.69
3. 12 20 26 12 20 26
4. 16 28 35 16 29 36
5. 30 40 44 27 40 49
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 5.21 15.58
2. 5.23 15.65
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 9.11 27.24
2. 10.67 31.91
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl1sf-100kflows-ndrpdr
|
1. 8.82 26.38
2. 12.25 36.65
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 5.22 3.51
2. 5.25 3.53
3. 10 16 22 10 15 26
4. 25 43 58 22 40 74
5. 54 79 91 53 78 90
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 10.41 6.99
2. 10.59 7.12
3. 10 20 31 10 19 26
4. 24 43 53 21 39 50
5. 41 55 62 41 54 61
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 17.28 11.61
2. 19.08 12.82
3. 10 14 17 10 12 16
4. 20 29 35 19 28 32
5. 44 88 148 35 47 65
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 3.08 37.87
2. 3.11 38.25
3. 12 28 40 12 25 39
4. 15 45 52 14 50 58
5. 37 51 63 40 53 63
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 2.86 35.19
2. 3.07 37.74
3. 12 15 27 12 12 15
4. 15 41 48 14 40 46
5. 31 49 58 30 48 61
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 2.72 33.47
2. 3.16 38.89
3. 12 23 28 12 23 28
4. 13 33 37 13 33 41
5. 24 35 38 26 35 41
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 5.21 15.58
2. 5.26 15.74
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 9.14 27.32
2. 10.65 31.85
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr
|
1. 8.97 26.83
2. 12.26 36.66
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 5.13 3.44
2. 5.22 3.51
3. 10 34 76 10 60 71
4. 32 65 77 23 64 77
5. 61 87 111 61 86 101
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 10.39 6.98
2. 10.65 7.16
3. 10 17 25 10 19 28
4. 20 37 44 18 36 43
5. 43 58 65 46 60 67
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 16.05 10.78
2. 18.04 12.13
3. 10 17 25 10 14 18
4. 15 22 28 15 21 27
5. 32 43 56 35 88 172
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 3.10 38.20
2. 3.12 38.39
3. 12 36 43 12 36 44
4. 21 46 54 23 50 59
5. 42 54 63 44 57 66
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 2.84 34.99
2. 3.10 38.10
3. 12 15 28 12 12 23
4. 19 46 58 18 46 56
5. 34 48 57 31 48 60
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 2.75 33.79
2. 3.14 38.67
3. 12 13 25 12 12 24
4. 13 33 36 12 32 38
5. 29 36 41 28 38 44
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 5.20 15.56
2. 5.24 15.68
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 9.17 27.43
2. 10.71 32.02
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl1sl-100flows-ndrpdr
|
1. 8.74 26.14
2. 12.23 36.58
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 5.20 3.50
2. 5.23 3.51
3. 10 43 64 10 44 63
4. 31 57 73 21 59 79
5. 52 72 85 56 74 85
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 10.45 7.02
2. 10.67 7.17
3. 10 14 18 10 15 20
4. 18 27 33 18 26 32
5. 39 50 58 41 51 58
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 17.68 11.88
2. 18.78 12.62
3. 10 11 16 10 10 14
4. 19 28 34 19 28 34
5. 35 52 79 37 55 97
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 3.09 37.96
2. 3.12 38.34
3. 12 36 42 12 36 42
4. 20 46 53 22 51 58
5. 44 54 62 46 60 71
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 2.84 34.94
2. 3.08 37.86
3. 12 18 28 12 15 21
4. 13 39 51 14 43 58
5. 31 49 60 31 50 63
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 2.79 34.30
2. 3.16 38.87
3. 12 17 27 12 16 26
4. 13 34 40 13 34 44
5. 30 39 43 29 40 47
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 5.12 15.32
2. 5.20 15.55
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 9.98 29.85
2. 10.35 30.95
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl1sl-100kflows-ndrpdr
|
1. 8.98 26.85
2. 12.24 36.60
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 5.21 3.50
2. 5.25 3.53
3. 10 14 29 10 19 29
4. 25 42 52 24 40 50
5. 52 70 84 49 70 85
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 10.41 7.00
2. 10.64 7.15
3. 10 13 18 10 13 19
4. 15 35 44 16 37 43
5. 38 51 60 45 57 66
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 16.59 11.15
2. 18.69 12.56
3. 10 16 25 10 14 25
4. 17 26 32 16 24 30
5. 36 51 71 36 57 153
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 3.10 38.20
2. 3.10 38.20
3. 12 24 40 12 15 38
4. 19 42 52 16 46 56
5. 30 48 58 31 50 60
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 2.86 35.16
2. 3.10 38.10
3. 12 25 30 12 19 28
4. 13 38 51 13 40 47
5. 35 49 58 33 48 59
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 2.75 33.89
2. 3.17 38.96
3. 12 13 24 12 12 24
4. 13 31 35 12 29 37
5. 29 38 42 29 41 46
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 5.15 15.41
2. 5.23 15.64
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 9.09 27.20
2. 10.60 31.70
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr
|
1. 9.04 27.02
2. 12.24 36.60
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 5.17 3.48
2. 5.27 3.54
3. 11 23 36 10 26 34
4. 21 35 43 22 33 45
5. 51 71 87 52 70 84
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 10.39 6.98
2. 10.63 7.15
3. 10 11 33 10 15 21
4. 17 29 37 18 29 36
5. 33 46 53 36 48 55
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 15.16 10.19
2. 16.35 10.99
3. 10 21 29 10 12 20
4. 29 33 37 16 32 38
5. 28 36 42 31 41 59
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 3.11 38.29
2. 3.11 38.29
3. 12 30 38 12 27 36
4. 17 48 57 13 48 57
5. 41 53 61 45 58 69
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 3.08 37.84
2. 3.08 37.84
3. 12 15 30 12 12 26
4. 13 50 62 12 48 60
5. 33 47 58 34 47 58
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 2.93 36.07
2. 3.16 38.88
3. 12 13 24 12 12 23
4. 13 34 40 12 35 40
5. 31 38 42 29 40 46
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 5.23 15.63
2. 5.28 15.79
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 10.25 30.65
2. 10.61 31.74
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl50sf-100flows-ndrpdr
|
1. 8.89 26.59
2. 12.25 36.63
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 5.14 3.46
2. 5.25 3.53
3. 10 39 57 10 42 55
4. 20 62 72 17 63 77
5. 63 89 104 65 86 97
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 10.47 7.04
2. 10.61 7.13
3. 10 22 39 10 19 38
4. 14 33 40 15 30 35
5. 40 51 59 44 54 61
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 15.65 10.52
2. 16.96 11.40
3. 10 16 21 10 14 22
4. 16 27 34 16 27 34
5. 28 36 42 30 39 52
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 3.12 38.33
2. 3.12 38.33
3. 12 18 25 12 15 25
4. 20 34 39 19 36 44
5. 33 42 52 35 44 54
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 3.09 38.05
2. 3.09 38.05
3. 12 15 30 12 12 27
4. 13 40 52 12 46 58
5. 30 46 57 29 46 60
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 2.99 36.81
2. 3.14 38.69
3. 12 26 29 12 25 28
4. 13 36 43 12 37 44
5. 30 39 43 29 40 47
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 5.13 15.34
2. 5.23 15.65
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 9.96 29.79
2. 10.22 30.56
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl50sf-100kflows-ndrpdr
|
1. 9.49 28.37
2. 12.24 36.62
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 5.16 3.47
2. 5.26 3.54
3. 10 19 25 10 17 28
4. 13 22 31 17 25 32
5. 53 70 82 52 68 80
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 10.04 6.75
2. 10.23 6.87
3. 10 19 22 10 18 23
4. 17 38 47 18 37 47
5. 33 42 48 40 49 57
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 18.18 12.22
2. 19.21 12.91
3. 10 21 31 10 20 30
4. 18 27 33 17 25 30
5. 38 58 107 39 55 87
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 3.08 37.95
2. 3.08 37.95
3. 12 17 37 12 14 35
4. 21 48 57 23 50 60
5. 40 54 63 45 59 70
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 3.02 37.13
2. 3.08 37.88
3. 12 15 30 12 12 26
4. 13 48 59 12 48 60
5. 35 48 60 38 51 61
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 3.01 37.08
2. 3.17 38.98
3. 12 18 27 12 13 24
4. 15 33 37 13 34 39
5. 30 39 42 29 40 45
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 5.16 15.44
2. 5.24 15.67
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 10.25 30.66
2. 10.66 31.88
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr
|
1. 9.70 29.00
2. 12.25 36.65
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 5.25 3.53
2. 5.28 3.55
3. 10 22 40 10 23 56
4. 30 55 68 17 55 66
5. 57 74 93 56 72 83
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 10.41 6.99
2. 10.62 7.14
3. 10 16 25 10 16 28
4. 17 27 37 17 27 35
5. 36 45 52 39 49 55
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 17.00 11.43
2. 18.01 12.11
3. 10 15 20 10 12 19
4. 17 24 29 16 23 28
5. 35 45 63 31 41 51
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 3.11 38.21
2. 3.11 38.21
3. 12 18 36 12 15 33
4. 13 53 62 12 55 67
5. 41 54 61 44 59 69
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 3.10 38.11
2. 3.10 38.11
3. 12 24 30 12 16 27
4. 13 48 58 12 48 56
5. 34 48 59 38 52 64
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 3.05 37.56
2. 3.15 38.71
3. 12 25 29 12 23 27
4. 13 36 42 12 39 45
5. 30 39 43 30 40 46
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 5.24 15.67
2. 5.27 15.75
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 10.28 30.73
2. 10.68 31.94
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl50sl-100flows-ndrpdr
|
1. 9.88 29.55
2. 12.27 36.70
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 5.17 3.47
2. 5.24 3.52
3. 10 14 28 10 14 30
4. 21 46 61 16 64 73
5. 59 79 99 57 76 91
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 10.40 6.99
2. 10.62 7.14
3. 10 15 21 10 14 20
4. 17 31 39 17 29 37
5. 34 44 50 39 48 54
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 16.66 11.19
2. 18.13 12.19
3. 10 21 34 10 18 33
4. 18 29 34 18 29 34
5. 36 44 57 37 55 127
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 3.12 38.36
2. 3.12 38.36
3. 12 18 39 12 15 34
4. 13 53 61 13 55 64
5. 41 54 61 44 59 71
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 3.10 38.17
2. 3.09 37.98
3. 12 28 30 12 12 16
4. 13 52 70 12 48 59
5. 33 49 60 37 50 62
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 2.96 36.39
2. 3.14 38.64
3. 12 20 29 12 12 12
4. 13 36 42 12 37 44
5. 29 39 43 29 40 46
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 5.34 15.97
2. 5.40 16.14
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 10.20 30.51
2. 10.62 31.75
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl50sl-100kflows-ndrpdr
|
1. 9.67 28.91
2. 12.25 36.64
|
40ge2p1vic1385-eth-l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 5.16 3.47
2. 5.24 3.52
3. 10 25 40 10 30 41
4. 26 54 68 22 55 66
5. 62 82 97 59 76 89
|
64b-2t2c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 10.29 6.91
2. 10.57 7.11
3. 11 35 49 10 39 49
4. 20 34 40 19 32 39
5. 45 60 68 45 59 68
|
64b-4t4c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 16.29 10.95
2. 17.62 11.84
3. 10 15 17 10 13 17
4. 17 24 30 16 23 29
5. 30 38 47 31 40 55
|
1518b-1t1c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 3.10 38.17
2. 3.10 38.17
3. 12 19 38 11 15 35
4. 13 55 64 13 58 73
5. 38 52 63 42 58 67
|
1518b-2t2c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 2.99 36.83
2. 3.08 37.96
3. 12 15 28 12 12 21
4. 13 49 63 12 47 58
5. 34 48 64 35 47 61
|
1518b-4t4c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 2.79 34.34
2. 3.15 38.72
3. 12 15 24 12 13 23
4. 13 37 42 12 37 45
5. 30 39 43 29 40 45
|
imix-1t1c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 5.16 15.43
2. 5.24 15.67
|
imix-2t2c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 10.06 30.09
2. 10.36 30.99
|
imix-4t4c-eth-
l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr
|
1. 9.55 28.56
2. 12.25 36.63
|
40ge2p1vic1385-eth-l2bdbasemaclrn-macip-iacl10sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 3.80 2.55
2. 3.80 2.55
3. 10 48 107 10 29 100
4. 11 84 112 11 92 115
5. 57 116 131 63 116 126
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 7.08 4.76
2. 7.18 4.82
3. 10 33 44 10 33 42
4. 19 55 65 17 55 64
5. 37 55 63 38 55 66
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 13.23 8.89
2. 13.59 9.14
3. 10 30 37 10 25 35
4. 15 34 41 19 35 42
5. 39 45 52 29 48 55
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 3.08 37.90
2. 3.11 38.28
3. 12 20 43 12 21 41
4. 14 64 74 14 69 77
5. 56 68 80 62 78 86
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 2.89 35.56
2. 3.10 38.14
3. 12 18 30 12 12 25
4. 13 44 52 12 45 55
5. 32 45 54 38 52 64
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 2.76 34.01
2. 3.15 38.73
3. 12 13 25 12 12 24
4. 13 36 42 12 37 44
5. 30 39 42 30 40 47
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 3.54 10.60
2. 3.76 11.25
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 6.78 20.29
2. 6.88 20.57
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100flows-ndrpdr
|
1. 8.90 26.62
2. 12.18 36.41
|
40ge2p1vic1385-eth-l2bdbasemaclrn-macip-iacl10sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 3.48 2.34
2. 3.64 2.45
3. 10 21 60 10 23 62
4. 24 98 128 30 107 134
5. 64 113 140 70 115 135
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 6.63 4.45
2. 6.69 4.50
3. 10 21 49 10 21 39
4. 13 42 56 13 41 54
5. 39 58 68 44 64 73
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 11.30 7.59
2. 11.97 8.04
3. 11 24 33 10 21 30
4. 18 33 47 19 32 44
5. 46 85 207 38 72 193
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 3.12 38.38
2. 3.12 38.38
3. 12 18 21 12 16 28
4. 23 49 59 25 53 63
5. 54 71 84 56 80 90
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 3.00 36.95
2. 3.08 37.89
3. 12 16 30 12 13 27
4. 13 41 50 16 42 58
5. 33 49 56 34 50 58
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 2.81 34.57
2. 3.15 38.78
3. 12 23 28 12 20 27
4. 14 35 39 12 37 43
5. 28 39 43 29 41 48
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 3.38 10.12
2. 3.44 10.28
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 6.23 18.62
2. 6.32 18.90
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-100kflows-ndrpdr
|
1. 8.93 26.70
2. 11.63 34.79
|
40ge2p1vic1385-eth-l2bdbasemaclrn-macip-iacl10sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 3.61 2.43
2. 3.61 2.43
3. 10 13 41 10 19 63
4. 22 86 110 21 85 109
5. 62 97 126 61 97 124
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 6.68 4.49
2. 6.77 4.55
3. 10 17 33 10 11 32
4. 12 37 45 12 33 44
5. 29 42 51 39 54 69
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 12.23 8.22
2. 12.54 8.42
3. 10 11 21 10 11 16
4. 18 39 46 18 41 49
5. 30 43 50 38 51 64
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 3.09 38.06
2. 3.09 38.06
3. 12 19 43 12 22 43
4. 21 69 79 24 74 84
5. 56 69 78 66 79 88
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 2.78 34.16
2. 3.08 37.94
3. 12 16 30 12 13 27
4. 13 47 62 12 48 59
5. 32 45 57 37 51 68
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 2.72 33.46
2. 3.16 38.87
3. 12 13 22 12 13 21
4. 13 35 41 12 37 44
5. 30 38 42 30 40 46
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 3.45 10.31
2. 3.56 10.66
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 6.34 18.96
2. 6.42 19.19
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl10sl-10kflows-ndrpdr
|
1. 8.95 26.75
2. 11.64 34.80
|
40ge2p1vic1385-eth-l2bdbasemaclrn-macip-iacl1sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 5.10 3.43
2. 5.18 3.48
3. 10 42 69 10 51 64
4. 18 54 68 22 56 70
5. 57 81 99 59 84 97
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 9.18 6.17
2. 9.30 6.25
3. 10 16 26 10 21 33
4. 15 29 37 19 32 41
5. 26 35 43 33 44 51
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 16.15 10.86
2. 16.81 11.30
3. 10 18 26 10 19 27
4. 12 20 27 14 21 27
5. 27 35 41 31 38 46
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 3.12 38.41
2. 3.12 38.41
3. 12 37 41 11 37 44
4. 27 49 55 20 53 61
5. 42 53 60 45 57 72
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 3.08 37.88
2. 3.08 37.88
3. 12 29 35 12 27 30
4. 26 43 56 19 51 59
5. 27 44 58 29 45 61
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 2.99 36.73
2. 3.15 38.81
3. 12 14 23 12 12 19
4. 15 34 37 15 35 42
5. 31 39 43 32 41 46
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 5.07 15.17
2. 5.15 15.40
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 9.07 27.11
2. 9.21 27.56
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100flows-ndrpdr
|
1. 10.04 30.03
2. 12.25 36.64
|
40ge2p1vic1385-eth-l2bdbasemaclrn-macip-iacl1sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 4.73 3.18
2. 4.80 3.23
3. 10 31 42 10 28 42
4. 18 57 71 17 61 68
5. 58 81 113 66 83 99
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 8.53 5.73
2. 8.68 5.84
3. 10 28 47 10 25 43
4. 25 47 59 32 52 59
5. 27 52 63 33 55 71
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 13.85 9.31
2. 15.77 10.60
3. 10 16 22 10 15 24
4. 12 22 29 11 18 25
5. 28 37 50 32 44 58
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 3.11 38.25
2. 3.11 38.25
3. 12 38 45 12 38 44
4. 17 48 56 23 53 63
5. 43 55 61 45 60 69
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 3.06 37.61
2. 3.09 37.99
3. 12 29 37 12 27 35
4. 13 39 48 14 43 54
5. 33 46 57 36 48 61
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 2.83 34.80
2. 3.14 38.65
3. 12 15 24 12 15 23
4. 15 33 38 13 33 39
5. 28 36 39 28 37 42
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 4.61 13.78
2. 4.65 13.89
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 8.45 25.27
2. 8.57 25.63
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-100kflows-ndrpdr
|
1. 9.03 27.02
2. 12.26 36.68
|
40ge2p1vic1385-eth-l2bdbasemaclrn-macip-iacl1sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 4.80 3.23
2. 4.92 3.31
3. 10 12 30 10 12 24
4. 17 63 93 17 67 92
5. 63 95 116 66 95 101
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 7.81 5.25
2. 8.83 5.93
3. 10 26 48 10 20 33
4. 18 39 48 21 42 50
5. 21 36 47 31 45 64
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 14.80 9.94
2. 15.09 10.14
3. 10 15 22 10 15 21
4. 16 26 33 15 24 31
5. 25 35 47 28 43 64
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 3.10 38.10
2. 3.10 38.10
3. 12 21 35 12 21 35
4. 15 42 49 15 45 54
5. 37 48 56 39 52 62
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 2.86 35.23
2. 3.09 37.98
3. 12 15 29 12 13 26
4. 17 33 44 17 38 51
5. 32 47 59 37 49 61
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 2.74 33.69
2. 3.15 38.76
3. 12 17 27 12 16 26
4. 14 32 36 13 34 40
5. 30 37 41 30 39 45
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 4.71 14.09
2. 4.85 14.51
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 8.32 24.88
2. 8.59 25.69
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl1sl-10kflows-ndrpdr
|
1. 8.99 26.88
2. 12.24 36.61
|
40ge2p1vic1385-eth-l2bdbasemaclrn-macip-iacl50sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 3.39 2.28
2. 3.49 2.35
3. 10 51 97 10 13 89
4. 28 105 144 16 111 128
5. 71 124 146 75 128 136
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 6.31 4.24
2. 6.40 4.30
3. 10 18 33 10 20 35
4. 19 67 81 18 75 83
5. 49 71 81 55 79 85
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 11.32 7.61
2. 11.70 7.86
3. 11 23 38 10 21 43
4. 18 41 48 19 43 51
5. 33 47 59 39 56 73
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 3.10 38.19
2. 3.12 38.38
3. 12 28 48 12 28 46
4. 30 86 99 38 90 101
5. 71 91 105 80 100 115
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 2.84 34.95
2. 3.08 37.86
3. 12 15 29 12 12 26
4. 13 45 55 12 50 62
5. 34 48 60 37 49 66
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 2.81 34.53
2. 3.15 38.74
3. 12 13 27 12 13 26
4. 13 36 42 12 37 45
5. 30 39 43 30 40 48
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 3.27 9.77
2. 3.40 10.18
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 6.25 18.68
2. 6.31 18.88
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100flows-ndrpdr
|
1. 8.85 26.46
2. 11.91 35.61
|
40ge2p1vic1385-eth-l2bdbasemaclrn-macip-iacl50sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 3.29 2.21
2. 3.29 2.21
3. 10 13 72 10 26 102
4. 29 97 151 26 108 148
5. 68 130 145 82 133 144
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 5.80 3.90
2. 6.03 4.05
3. 10 53 67 10 34 77
4. 14 58 78 12 69 79
5. 52 77 86 61 86 93
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 11.14 7.49
2. 11.37 7.64
3. 11 18 28 10 17 28
4. 22 41 49 19 44 49
5. 33 44 50 41 54 65
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 3.07 37.77
2. 3.13 38.53
3. 12 31 55 12 31 45
4. 41 88 107 48 96 110
5. 87 108 132 103 127 146
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 2.68 33.02
2. 3.06 37.61
3. 12 23 32 12 13 27
4. 13 51 65 13 47 56
5. 34 46 57 40 52 65
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 2.79 34.37
2. 3.15 38.75
3. 12 13 25 12 13 24
4. 13 37 42 12 37 44
5. 31 40 43 30 41 46
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 2.82 8.42
2. 3.14 9.40
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 5.80 17.34
2. 5.87 17.56
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-100kflows-ndrpdr
|
1. 9.01 26.93
2. 11.28 33.75
|
40ge2p1vic1385-eth-l2bdbasemaclrn-macip-iacl50sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required MACIP ACL rules are applied to input paths of both DUT1 interfaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 3.24 2.18
2. 3.29 2.21
3. 10 29 71 10 23 65
4. 18 81 127 19 81 124
5. 74 137 153 82 127 142
|
64b-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 5.79 3.89
2. 6.03 4.05
3. 10 45 65 10 61 76
4. 16 59 80 19 63 84
5. 47 75 86 56 81 94
|
64b-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 11.14 7.49
2. 11.51 7.73
3. 11 22 34 10 18 33
4. 20 40 47 20 42 50
5. 33 47 53 38 51 62
|
1518b-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 3.08 37.93
2. 3.11 38.32
3. 12 29 43 12 31 45
4. 26 88 101 30 93 106
5. 80 104 121 88 110 128
|
1518b-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 2.85 35.09
2. 3.09 38.02
3. 12 16 30 12 14 27
4. 13 47 54 12 51 63
5. 34 47 58 38 50 64
|
1518b-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 2.79 34.27
2. 3.17 39.03
3. 12 13 21 12 12 20
4. 13 36 42 12 37 43
5. 31 39 43 30 41 46
|
imix-1t1c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 2.83 8.47
2. 3.21 9.60
|
imix-2t2c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 5.86 17.53
2. 5.92 17.71
|
imix-4t4c-eth-l2bdbasemaclrn-
macip-iacl50sl-10kflows-ndrpdr
|
1. 8.92 26.68
2. 11.23 33.58
|
40ge2p1vic1385-eth-l2bdbasemaclrn-ndrpdr
RFC2544: Pkt throughput L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 8.89 5.98
2. 10.13 6.81
3. 11 30 43 10 22 37
4. 26 40 46 21 39 47
5. 68 86 101 70 87 102
|
64b-2t2c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 14.56 9.78
2. 20.15 13.54
3. 13 25 32 10 11 18
4. 28 40 48 23 36 44
5. 38 44 50 39 46 52
|
64b-4t4c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 27.71 18.62
2. 31.25 21.00
3. 10 15 22 10 15 19
4. 15 19 23 15 20 24
5. 25 29 33 24 28 32
|
1518b-1t1c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 3.10 38.10
2. 3.10 38.10
3. 12 23 34 11 18 31
4. 13 45 56 12 45 52
5. 34 47 54 36 46 54
|
1518b-2t2c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 3.08 37.89
2. 3.08 37.89
3. 12 15 27 11 13 24
4. 15 37 45 14 33 47
5. 35 48 56 35 48 56
|
1518b-4t4c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 2.73 33.63
2. 3.16 38.88
3. 12 19 26 11 16 26
4. 14 36 41 12 35 42
5. 27 39 46 28 37 42
|
imix-1t1c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 9.78 29.26
2. 10.18 30.46
|
imix-2t2c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 10.63 31.78
2. 11.86 35.47
|
imix-4t4c-
eth-l2bdbasemaclrn-ndrpdr
|
1. 8.81 26.35
2. 12.29 36.77
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 5.15 3.46
2. 5.17 3.48
3. 10 19 30 10 25 30
4. 20 39 58 21 45 58
5. 55 73 88 54 72 87
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 9.99 6.72
2. 10.22 6.87
3. 11 25 32 11 25 32
4. 18 27 37 19 27 35
5. 34 44 51 37 47 54
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 14.91 10.02
2. 16.64 11.18
3. 11 15 19 10 13 17
4. 20 28 33 18 26 31
5. 30 39 49 32 53 127
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 3.12 38.33
2. 3.12 38.33
3. 12 32 43 12 28 44
4. 22 47 61 25 53 67
5. 45 60 70 47 62 73
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 2.88 35.39
2. 3.08 37.96
3. 12 17 29 12 12 16
4. 18 40 51 13 43 52
5. 33 49 55 32 51 64
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 2.75 33.87
2. 3.15 38.77
3. 12 17 27 12 17 25
4. 13 33 39 12 34 39
5. 30 38 42 29 40 44
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 5.10 15.25
2. 5.13 15.33
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 9.15 27.37
2. 10.22 30.57
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl10sf-100flows-ndrpdr
|
1. 8.94 26.72
2. 12.24 36.60
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 5.17 3.47
2. 5.22 3.51
3. 10 23 32 10 24 34
4. 22 43 64 21 41 63
5. 54 75 92 57 78 91
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 9.98 6.71
2. 10.23 6.88
3. 10 20 23 10 15 22
4. 22 42 52 22 39 47
5. 38 48 55 38 48 55
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 16.37 11.00
2. 17.51 11.77
3. 10 27 34 10 14 22
4. 20 28 34 17 26 32
5. 35 44 58 31 39 47
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 3.12 38.33
2. 3.12 38.33
3. 12 19 35 12 16 32
4. 24 44 52 24 46 57
5. 42 54 64 48 59 68
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 2.89 35.60
2. 3.09 37.99
3. 12 17 21 12 13 20
4. 13 38 51 13 41 53
5. 32 47 56 32 49 60
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 2.87 35.26
2. 3.15 38.78
3. 12 13 19 12 13 19
4. 14 34 38 15 34 40
5. 30 38 42 30 40 46
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 5.18 15.49
2. 5.21 15.57
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 9.28 27.75
2. 10.27 30.72
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl10sf-100kflows-ndrpdr
|
1. 8.98 26.86
2. 12.24 36.62
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 5.18 3.48
2. 5.23 3.51
3. 10 35 54 10 35 52
4. 22 35 46 20 37 46
5. 54 70 86 52 69 82
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 10.09 6.78
2. 10.29 6.92
3. 11 24 32 11 24 34
4. 18 29 37 19 31 38
5. 38 48 55 39 48 55
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 14.60 9.81
2. 15.87 10.67
3. 10 11 20 10 11 15
4. 11 15 20 12 16 21
5. 27 36 45 28 39 62
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 3.12 38.37
2. 3.12 38.37
3. 12 19 41 12 15 40
4. 25 54 62 26 58 65
5. 43 54 61 45 61 72
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 2.92 35.90
2. 3.08 37.93
3. 12 22 29 12 18 27
4. 13 44 58 12 44 53
5. 33 48 59 35 47 62
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 2.76 33.90
2. 3.15 38.80
3. 12 13 24 12 12 21
4. 15 34 38 13 35 40
5. 32 40 43 30 41 46
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 5.17 15.48
2. 5.20 15.55
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 9.17 27.43
2. 10.20 30.50
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl10sf-10kflows-ndrpdr
|
1. 8.93 26.72
2. 12.27 36.68
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 5.13 3.45
2. 5.21 3.50
3. 10 25 49 10 28 50
4. 23 43 55 20 42 52
5. 52 72 91 54 75 93
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 10.11 6.79
2. 10.23 6.88
3. 11 41 50 11 30 45
4. 21 37 45 22 37 45
5. 43 54 61 42 53 61
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 15.83 10.64
2. 16.89 11.35
3. 10 14 21 10 14 24
4. 17 24 29 18 24 29
5. 31 40 50 31 40 54
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 3.12 38.44
2. 3.12 38.44
3. 12 22 33 12 20 32
4. 24 44 53 25 47 55
5. 39 49 60 41 54 67
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 2.87 35.34
2. 3.08 37.90
3. 12 16 28 12 12 24
4. 15 33 43 13 35 46
5. 31 48 61 33 46 62
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 2.76 33.96
2. 3.17 39.06
3. 12 17 28 12 12 16
4. 13 37 41 12 37 44
5. 31 39 42 30 41 46
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 5.11 15.27
2. 5.18 15.50
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 9.26 27.71
2. 10.21 30.53
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl10sl-100flows-ndrpdr
|
1. 9.04 27.05
2. 12.24 36.60
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 5.15 3.46
2. 5.20 3.50
3. 10 17 34 10 20 35
4. 24 47 61 21 52 64
5. 57 85 101 56 84 96
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 10.07 6.77
2. 10.24 6.88
3. 10 28 36 10 28 37
4. 22 42 51 21 39 49
5. 41 52 60 43 53 60
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 15.80 10.62
2. 17.46 11.73
3. 11 20 27 10 14 19
4. 19 27 33 20 27 32
5. 36 45 57 40 58 132
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 3.12 38.34
2. 3.12 38.34
3. 12 34 43 12 33 43
4. 17 48 53 16 53 59
5. 42 54 61 45 59 68
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 2.91 35.84
2. 3.09 38.06
3. 12 24 31 12 17 29
4. 13 48 62 13 50 61
5. 33 48 60 38 50 63
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 2.71 33.32
2. 3.15 38.71
3. 12 25 29 12 23 28
4. 13 33 37 12 34 40
5. 23 37 43 23 38 45
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 5.18 15.49
2. 5.20 15.56
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 10.01 29.95
2. 10.30 30.81
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl10sl-100kflows-ndrpdr
|
1. 9.90 29.59
2. 12.24 36.60
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 5.10 3.43
2. 5.20 3.50
3. 10 21 39 10 28 37
4. 26 43 55 22 44 54
5. 57 78 92 57 78 91
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 10.01 6.72
2. 10.27 6.90
3. 11 21 30 11 20 24
4. 20 28 34 20 28 33
5. 40 51 59 42 53 60
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 16.11 10.83
2. 18.02 12.11
3. 11 17 22 10 16 20
4. 17 25 30 16 24 29
5. 43 63 103 44 109 172
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 3.12 38.41
2. 3.12 38.41
3. 12 20 39 12 14 35
4. 23 48 57 22 52 61
5. 42 52 61 44 57 65
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 3.09 37.98
2. 3.09 37.98
3. 12 18 23 12 17 20
4. 18 40 53 16 43 54
5. 32 50 58 31 49 57
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 2.77 34.13
2. 3.16 38.87
3. 12 15 23 12 13 17
4. 14 36 40 12 35 39
5. 28 37 41 28 38 42
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 5.18 15.50
2. 5.21 15.57
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 10.02 29.95
2. 10.31 30.84
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl10sl-10kflows-ndrpdr
|
1. 9.98 29.85
2. 12.27 36.71
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 5.18 3.48
2. 5.21 3.50
3. 10 22 28 10 22 29
4. 21 35 49 22 35 50
5. 57 79 91 57 77 87
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 10.02 6.73
2. 10.27 6.90
3. 11 21 29 10 20 25
4. 19 31 46 18 30 39
5. 36 46 53 39 48 55
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 15.69 10.54
2. 17.11 11.50
3. 11 16 25 10 13 21
4. 17 26 32 17 25 31
5. 30 39 47 32 44 67
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 3.04 37.38
2. 3.13 38.52
3. 12 18 31 12 12 16
4. 22 37 42 24 40 44
5. 41 55 65 44 60 68
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 3.03 37.29
2. 3.09 38.04
3. 12 21 30 12 14 27
4. 20 46 55 13 49 61
5. 30 43 52 34 46 52
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 2.75 33.80
2. 3.16 38.88
3. 12 20 29 12 18 28
4. 16 35 39 15 34 40
5. 31 39 42 29 41 46
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 5.18 15.50
2. 5.24 15.66
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 9.91 29.64
2. 10.27 30.72
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl1sf-100flows-ndrpdr
|
1. 9.91 29.63
2. 12.27 36.69
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 5.09 3.42
2. 5.19 3.49
3. 10 24 43 10 27 49
4. 21 44 59 22 45 61
5. 52 69 89 54 70 86
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 10.01 6.73
2. 10.26 6.89
3. 10 12 23 10 12 13
4. 18 33 43 18 31 41
5. 36 47 56 40 51 60
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 15.18 10.20
2. 17.04 11.45
3. 11 21 32 10 16 28
4. 18 33 39 18 31 37
5. 32 41 48 35 52 109
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 3.09 38.06
2. 3.09 38.06
3. 12 22 38 12 23 37
4. 13 56 68 13 57 66
5. 42 55 61 48 60 69
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 2.84 34.89
2. 3.10 38.18
3. 12 16 23 12 12 20
4. 13 43 54 12 42 58
5. 32 45 53 33 49 59
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 2.77 34.10
2. 3.16 38.83
3. 12 25 29 12 24 28
4. 13 34 41 12 34 43
5. 30 38 42 29 39 45
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 5.17 15.48
2. 5.23 15.63
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 9.91 29.65
2. 10.25 30.64
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl1sf-100kflows-ndrpdr
|
1. 8.74 26.14
2. 12.27 36.70
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 5.19 3.49
2. 5.22 3.51
3. 10 30 43 10 30 45
4. 23 37 49 24 39 49
5. 49 69 86 49 70 85
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 9.77 6.56
2. 9.96 6.69
3. 10 20 31 10 16 27
4. 20 36 44 21 35 44
5. 31 41 48 36 46 54
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 16.98 11.41
2. 18.57 12.48
3. 11 13 21 10 14 20
4. 17 26 32 17 24 30
5. 49 105 154 36 48 70
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 3.11 38.20
2. 3.11 38.20
3. 12 22 38 12 22 35
4. 13 53 64 13 57 68
5. 42 56 63 45 60 69
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 2.83 34.78
2. 3.11 38.25
3. 12 17 22 12 16 19
4. 14 46 63 12 48 66
5. 33 48 57 34 49 58
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 2.64 32.46
2. 3.14 38.67
3. 12 23 29 12 21 27
4. 13 34 38 12 33 40
5. 30 39 43 29 40 45
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 5.09 15.23
2. 5.19 15.51
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 9.19 27.49
2. 10.01 29.94
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl1sf-10kflows-ndrpdr
|
1. 9.89 29.58
2. 12.25 36.64
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 5.11 3.43
2. 5.18 3.48
3. 10 36 69 10 25 73
4. 22 55 74 24 59 77
5. 62 90 107 63 87 100
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 10.05 6.75
2. 10.25 6.89
3. 11 22 31 10 16 21
4. 20 27 34 20 30 35
5. 36 49 57 38 51 59
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 15.55 10.45
2. 17.92 12.04
3. 11 19 26 10 15 22
4. 18 26 32 15 23 29
5. 39 69 183 29 39 54
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 3.12 38.35
2. 3.12 38.35
3. 12 19 35 12 15 31
4. 13 54 62 13 56 65
5. 44 54 63 45 57 67
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 2.93 36.00
2. 3.09 38.03
3. 12 16 29 12 12 24
4. 13 42 53 15 38 51
5. 33 48 59 34 49 61
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 2.72 33.46
2. 3.14 38.68
3. 12 18 32 12 17 33
4. 16 36 40 16 37 43
5. 32 39 42 29 40 45
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 5.17 15.47
2. 5.23 15.63
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 9.96 29.77
2. 10.30 30.80
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl1sl-100flows-ndrpdr
|
1. 9.66 28.90
2. 12.25 36.65
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 5.09 3.42
2. 5.19 3.49
3. 10 20 45 10 27 46
4. 28 52 76 33 53 71
5. 53 71 86 54 73 85
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 10.03 6.74
2. 10.23 6.88
3. 11 30 39 10 18 34
4. 19 29 37 18 30 40
5. 38 49 55 41 53 59
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 14.83 9.96
2. 16.46 11.06
3. 11 20 29 10 17 30
4. 28 33 37 28 35 40
5. 28 36 43 30 40 64
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 3.07 37.72
2. 3.11 38.29
3. 12 18 33 12 15 30
4. 19 48 57 18 52 59
5. 43 55 62 48 60 72
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 2.86 35.23
2. 3.09 37.98
3. 12 27 30 12 12 21
4. 13 42 54 12 43 52
5. 32 47 55 30 47 59
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 2.69 33.12
2. 3.14 38.68
3. 12 13 24 12 12 26
4. 13 34 39 12 34 41
5. 28 40 44 29 40 48
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 5.10 15.25
2. 5.18 15.49
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 9.87 29.53
2. 10.26 30.69
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl1sl-100kflows-ndrpdr
|
1. 9.84 29.44
2. 12.25 36.65
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 5.10 3.43
2. 5.19 3.49
3. 10 16 23 10 18 28
4. 22 37 51 21 38 52
5. 56 71 84 53 67 81
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 9.85 6.62
2. 10.04 6.75
3. 10 14 29 10 11 11
4. 18 30 38 19 32 40
5. 33 43 51 39 50 58
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 16.27 10.94
2. 17.84 11.99
3. 11 24 35 10 17 30
4. 21 31 37 17 29 34
5. 36 45 60 32 48 80
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 3.11 38.26
2. 3.11 38.26
3. 12 18 35 12 15 32
4. 16 49 57 17 52 61
5. 43 56 63 46 59 68
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 2.84 34.98
2. 3.08 37.90
3. 12 22 31 12 18 29
4. 18 39 50 13 42 53
5. 31 44 52 31 50 58
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 2.73 33.60
2. 3.15 38.71
3. 12 13 23 12 13 22
4. 13 34 38 12 36 41
5. 25 38 43 25 40 47
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 5.10 15.24
2. 5.19 15.52
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 9.81 29.35
2. 10.27 30.73
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl1sl-10kflows-ndrpdr
|
1. 9.88 29.55
2. 12.23 36.59
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 5.08 3.42
2. 5.10 3.43
3. 10 22 37 10 16 27
4. 22 46 60 22 48 57
5. 61 94 111 69 95 105
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 9.98 6.71
2. 10.17 6.84
3. 10 40 53 10 36 51
4. 31 52 60 28 48 55
5. 48 61 70 45 59 71
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 16.09 10.81
2. 17.82 11.97
3. 11 16 21 10 14 20
4. 17 25 30 15 22 28
5. 44 71 130 32 62 146
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 3.08 37.91
2. 3.11 38.29
3. 12 19 36 12 15 33
4. 21 51 67 17 51 64
5. 42 52 60 44 57 65
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 2.85 35.11
2. 3.08 37.85
3. 12 16 22 12 13 17
4. 13 46 54 12 44 54
5. 30 44 56 31 48 60
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 2.67 32.83
2. 3.15 38.72
3. 12 14 25 12 14 25
4. 13 34 39 12 35 41
5. 30 38 42 29 40 46
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 5.08 15.19
2. 5.12 15.31
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 9.18 27.44
2. 10.25 30.66
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl50sf-100flows-ndrpdr
|
1. 8.94 26.73
2. 12.27 36.71
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 5.07 3.41
2. 5.12 3.44
3. 10 15 25 10 17 29
4. 22 48 63 22 45 62
5. 58 81 94 58 81 92
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 10.02 6.74
2. 10.18 6.84
3. 10 19 22 10 15 22
4. 20 34 41 20 29 38
5. 39 48 55 38 49 56
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 16.59 11.15
2. 18.75 12.60
3. 10 12 18 10 13 20
4. 21 32 38 19 30 35
5. 53 117 142 38 55 79
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 3.09 38.05
2. 3.09 38.05
3. 12 33 42 12 27 44
4. 19 39 45 18 41 49
5. 36 44 54 39 48 57
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 2.89 35.52
2. 3.08 37.91
3. 12 19 29 12 15 20
4. 14 41 53 15 43 57
5. 33 47 58 38 50 61
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 2.75 33.85
2. 3.15 38.74
3. 12 15 22 12 15 20
4. 15 35 48 15 36 42
5. 29 37 41 29 38 44
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 5.04 15.09
2. 5.09 15.24
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 9.28 27.75
2. 10.22 30.57
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl50sf-100kflows-ndrpdr
|
1. 9.11 27.24
2. 12.27 36.71
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 5.04 3.39
2. 5.09 3.42
3. 10 15 32 10 16 31
4. 23 36 46 23 38 48
5. 54 72 87 53 74 85
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 10.06 6.76
2. 10.26 6.89
3. 11 44 52 10 30 50
4. 20 38 48 20 35 43
5. 40 50 57 40 50 57
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 15.54 10.45
2. 16.68 11.21
3. 10 13 20 10 16 22
4. 17 24 29 17 24 29
5. 30 38 45 29 40 61
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 3.11 38.28
2. 3.11 38.28
3. 12 27 41 12 20 41
4. 13 51 66 24 56 72
5. 44 56 63 49 60 69
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 2.92 35.88
2. 3.08 37.92
3. 12 16 27 12 12 16
4. 17 41 51 16 44 61
5. 31 44 56 32 46 59
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 2.68 32.95
2. 3.17 39.06
3. 12 16 27 12 13 20
4. 14 36 42 13 37 43
5. 31 39 42 30 40 45
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 5.03 15.05
2. 5.08 15.20
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 9.89 29.59
2. 10.29 30.76
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl50sf-10kflows-ndrpdr
|
1. 8.91 26.65
2. 12.25 36.65
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100 flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 5.06 3.40
2. 5.08 3.41
3. 10 23 39 10 24 41
4. 26 55 74 26 56 75
5. 57 76 93 58 79 94
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 10.05 6.75
2. 10.25 6.89
3. 10 21 24 10 11 14
4. 22 37 46 23 39 46
5. 40 54 61 42 53 59
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 15.58 10.47
2. 17.15 11.52
3. 11 22 33 10 15 26
4. 18 31 37 16 26 33
5. 35 55 111 31 45 98
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 3.12 38.33
2. 3.12 38.33
3. 12 35 45 12 30 44
4. 24 49 56 25 55 72
5. 44 56 64 48 61 69
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 3.02 37.21
2. 3.10 38.16
3. 12 20 29 12 18 22
4. 13 42 51 12 48 61
5. 33 47 59 37 52 65
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 2.72 33.48
2. 3.15 38.71
3. 12 18 28 12 17 27
4. 14 34 38 12 35 41
5. 29 37 41 29 38 43
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 5.00 14.97
2. 5.11 15.28
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 9.22 27.59
2. 10.28 30.74
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl50sl-100flows-ndrpdr
|
1. 8.90 26.63
2. 12.25 36.62
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 5.09 3.42
2. 5.11 3.44
3. 10 13 28 10 15 32
4. 21 51 69 21 54 73
5. 55 88 103 54 91 102
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 10.06 6.76
2. 10.27 6.90
3. 10 21 23 10 20 22
4. 24 43 50 21 40 47
5. 41 51 58 40 51 58
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 17.62 11.84
2. 18.61 12.50
3. 10 11 17 10 12 20
4. 20 30 37 19 27 34
5. 47 67 107 36 49 67
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 3.09 37.98
2. 3.10 38.17
3. 12 19 36 12 16 34
4. 23 45 51 17 48 62
5. 44 58 67 46 63 72
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 2.88 35.43
2. 3.09 38.00
3. 12 28 32 12 21 28
4. 16 39 49 17 42 57
5. 33 48 58 37 48 61
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 2.73 33.59
2. 3.14 38.64
3. 12 24 28 12 24 28
4. 13 32 38 13 32 40
5. 31 39 44 29 41 47
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 5.09 15.22
2. 5.12 15.30
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 8.88 26.57
2. 10.18 30.43
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl50sl-100kflows-ndrpdr
|
1. 8.98 26.86
2. 12.27 36.69
|
40ge2p1vic1385-eth-l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
RFC2544: Packet throughput L2BD test cases with ACL
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 5.00 3.36
2. 5.07 3.41
3. 10 19 37 10 20 44
4. 21 46 63 21 46 68
5. 56 76 89 57 77 93
|
64b-2t2c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 9.99 6.71
2. 10.24 6.88
3. 10 38 50 10 20 45
4. 22 44 51 21 41 48
5. 45 57 63 44 56 63
|
64b-4t4c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 16.24 10.91
2. 17.86 12.00
3. 10 21 29 10 16 24
4. 25 36 41 18 31 36
5. 38 51 77 33 40 53
|
1518b-1t1c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 3.12 38.39
2. 3.12 38.39
3. 12 21 36 12 20 33
4. 19 49 58 22 53 61
5. 44 56 64 47 62 71
|
1518b-2t2c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 2.91 35.79
2. 3.09 38.00
3. 12 18 30 12 16 26
4. 13 46 57 15 51 66
5. 34 49 62 37 48 59
|
1518b-4t4c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 2.77 34.14
2. 3.16 38.87
3. 12 13 22 12 13 21
4. 14 34 41 13 34 43
5. 30 39 43 29 40 45
|
imix-1t1c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 5.05 15.11
2. 5.12 15.30
|
imix-2t2c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 9.20 27.52
2. 10.24 30.62
|
imix-4t4c-eth-
l2bdbasemaclrn-oacl50sl-10kflows-ndrpdr
|
1. 9.04 27.05
2. 12.25 36.65
|
40ge2p1vic1385-eth-l2bdscale100kmaclrn-ndrpdr
RFC2544: Pkt throughput for L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 50k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 6.85 4.61
2. 7.06 4.75
3. 10 45 62 10 17 59
4. 21 55 64 19 52 63
5. 74 103 127 75 104 129
|
64b-2t2c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 12.39 8.32
2. 13.42 9.02
3. 11 17 26 10 11 11
4. 33 53 68 30 52 62
5. 46 56 66 48 58 66
|
64b-4t4c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 21.35 14.34
2. 26.21 17.61
3. 11 18 26 10 18 25
4. 20 27 32 20 27 33
5. 47 64 77 47 58 66
|
1518b-1t1c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 3.11 38.25
2. 3.11 38.25
3. 12 34 39 11 33 38
4. 19 49 60 12 49 66
5. 37 56 64 36 53 61
|
1518b-2t2c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 2.99 36.80
2. 3.05 37.55
3. 12 19 36 12 20 36
4. 16 43 54 14 45 56
5. 30 45 59 30 45 56
|
1518b-4t4c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 2.97 36.49
2. 3.15 38.75
3. 12 13 27 12 12 26
4. 19 36 42 16 35 39
5. 32 40 45 31 40 45
|
imix-1t1c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 6.40 19.15
2. 6.54 19.55
|
imix-2t2c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 11.72 35.05
2. 11.90 35.58
|
imix-4t4c-
eth-l2bdscale100kmaclrn-ndrpdr
|
1. 10.14 30.31
2. 12.30 36.79
|
40ge2p1vic1385-eth-l2bdscale10kmaclrn-ndrpdr
RFC2544: Pkt throughput for L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 5k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 7.45 5.01
2. 7.96 5.35
3. 10 15 21 10 14 29
4. 10 18 30 10 10 15
5. 62 76 89 61 75 88
|
64b-2t2c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 13.52 9.08
2. 15.42 10.36
3. 10 29 44 10 29 47
4. 26 46 57 31 46 55
5. 55 67 75 53 65 73
|
64b-4t4c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 23.80 15.99
2. 29.96 20.13
3. 10 15 18 10 14 17
4. 17 23 28 17 23 28
5. 37 43 49 34 39 45
|
1518b-1t1c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 3.10 38.17
2. 3.12 38.36
3. 12 24 34 11 16 32
4. 17 42 48 17 43 51
5. 37 49 58 37 49 58
|
1518b-2t2c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 2.97 36.55
2. 3.08 37.85
3. 12 13 26 12 12 23
4. 13 42 53 12 40 51
5. 32 46 57 35 43 52
|
1518b-4t4c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 2.77 34.05
2. 3.14 38.58
3. 12 21 27 11 13 25
4. 13 34 38 13 33 39
5. 27 41 48 25 40 46
|
imix-1t1c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 7.66 22.90
2. 7.77 23.25
|
imix-2t2c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 10.58 31.65
2. 11.81 35.33
|
imix-4t4c-
eth-l2bdscale10kmaclrn-ndrpdr
|
1. 8.90 26.62
2. 12.29 36.76
|
40ge2p1vic1385-eth-l2bdscale1mmaclrn-ndrpdr
RFC2544: Pkt throughput for L2BD test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 500k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 6.43 4.32
2. 6.52 4.38
3. 10 16 38 10 14 34
4. 26 69 79 23 69 82
5. 68 89 116 70 90 118
|
64b-2t2c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 11.82 7.94
2. 12.36 8.31
3. 11 31 57 10 27 54
4. 33 56 66 31 53 64
5. 59 74 84 56 70 81
|
64b-4t4c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 21.82 14.66
2. 23.28 15.65
3. 11 20 34 10 17 33
4. 25 35 42 22 33 38
5. 45 56 68 44 52 60
|
1518b-1t1c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 3.10 38.10
2. 3.10 38.10
3. 12 21 34 11 20 34
4. 17 50 61 15 48 56
5. 39 52 59 38 52 59
|
1518b-2t2c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 2.95 36.27
2. 3.05 37.53
3. 12 15 25 12 12 20
4. 13 50 60 12 47 63
5. 32 44 59 37 47 54
|
1518b-4t4c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 2.75 33.80
2. 3.15 38.70
3. 12 13 26 12 12 25
4. 13 37 43 12 37 44
5. 30 40 45 30 38 44
|
imix-1t1c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 5.88 17.59
2. 6.00 17.95
|
imix-2t2c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 11.61 34.73
2. 11.79 35.25
|
imix-4t4c-
eth-l2bdscale1mmaclrn-ndrpdr
|
1. 9.11 27.23
2. 12.29 36.76
|
40ge2p1vic1385-eth-l2patch-ndrpdr
RFC2544: Pkt throughput L2patch test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 patch DUT1 and DUT2 tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header,IPv4 header with static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2patch-ndrpdr
|
1. 12.75 8.57
2. 18.64 12.53
3. 9 12 18 9 10 16
4. 14 20 25 15 20 25
5. 38 45 53 38 46 54
|
64b-2t2c-eth-l2patch-ndrpdr
|
1. 21.72 14.60
2. 28.89 19.41
3. 9 13 17 9 11 15
4. 14 20 23 14 19 22
5. 20 23 26 19 22 25
|
64b-4t4c-eth-l2patch-ndrpdr
|
1. 25.55 17.17
2. 28.95 19.46
3. 9 11 13 9 10 12
4. 11 14 16 11 14 16
5. 13 16 18 13 15 18
|
1518b-1t1c-eth-l2patch-ndrpdr
|
1. 3.08 37.89
2. 3.08 37.89
3. 11 23 28 10 22 27
4. 11 43 55 11 43 54
5. 30 45 51 29 45 53
|
1518b-2t2c-eth-l2patch-ndrpdr
|
1. 2.82 34.69
2. 3.10 38.15
3. 11 17 25 10 13 19
4. 11 46 56 11 45 59
5. 31 46 57 32 47 60
|
1518b-4t4c-eth-l2patch-ndrpdr
|
1. 2.77 34.02
2. 3.15 38.75
3. 11 11 22 10 11 22
4. 11 32 39 11 33 43
5. 30 40 47 28 40 47
|
imix-1t1c-eth-l2patch-ndrpdr
|
1. 10.84 32.42
2. 11.80 35.29
|
imix-2t2c-eth-l2patch-ndrpdr
|
1. 10.05 30.06
2. 11.68 34.92
|
imix-4t4c-eth-l2patch-ndrpdr
|
1. 8.86 26.50
2. 12.23 36.59
|
40ge2p1vic1385-eth-l2xcbase-ndrpdr
RFC2544: Pkt throughput L2XC test cases
[Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
[Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
[Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with Cisco-VIC-1385.
[Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
[Ref] Applicable standard specifications: RFC2544.
|
Throughput:
1. Mpps Gbps (NDR)
2. Mpps Gbps (PDR)
One-Way Latency Percentiles in uSec at %PDR load,
one set per each direction:
3. P50 P90 P99 P50 P90 P99 (10% PDR)
4. P50 P90 P99 P50 P90 P99 (50% PDR)
5. P50 P90 P99 P50 P90 P99 (90% PDR)
|
|---|
64b-1t1c-eth-l2xcbase-ndrpdr
|
1. 10.29 6.92
2. 13.48 9.06
3. 10 21 28 10 27 34
4. 21 35 40 17 34 39
5. 60 75 86 50 61 79
|
64b-2t2c-eth-l2xcbase-ndrpdr
|
1. 18.31 12.31
2. 27.05 18.18
3. 10 15 17 9 14 16
4. 17 22 27 17 22 27
5. 34 40 46 33 38 43
|
64b-4t4c-eth-l2xcbase-ndrpdr
|
1. 26.70 17.94
2. 28.92 19.44
3. 10 13 18 9 12 16
4. 13 18 20 13 17 20
5. 16 19 21 16 19 22
|
1518b-1t1c-eth-l2xcbase-ndrpdr
|
1. 3.06 37.65
2. 3.08 37.84
3. 11 21 29 11 14 27
4. 13 41 57 13 40 53
5. 30 43 56 31 44 62
|
1518b-2t2c-eth-l2xcbase-ndrpdr
|
1. 2.81 34.57
2. 3.09 38.02
3. 11 14 20 11 11 17
4. 12 41 56 12 40 54
5. 31 48 62 33 46 61
|
1518b-4t4c-eth-l2xcbase-ndrpdr
|
1. 2.86 35.18
2. 3.14 38.68
3. 11 12 12 11 11 12
4. 15 35 43 14 35 41
5. 32 39 45 28 41 47
|
imix-1t1c-eth-l2xcbase-ndrpdr
|
1. 11.62 34.75
2. 11.91 35.63
|
imix-2t2c-eth-l2xcbase-ndrpdr
|
1. 10.42 31.16
2. 11.81 35.31
|
imix-4t4c-eth-l2xcbase-ndrpdr
|
1. 8.94 26.72
2. 12.22 36.56
|