device¶
container memif¶
eth2p-eth-l2bdbasemaclrn-eth-2memif-1dcr-dev¶
eth2p-eth-l2bdbasemaclrn-eth-2memif-1dcr-dev¶
L2 bridge-domain test cases with memif interface
- [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 for L2 switching of IPv4; Eth-IPv6-ICMPv6 for L2 switching of IPv6 use. Both apply to all links.
- [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain switching. Container is connected to VPP via Memif interface. Container is running same VPP version as running on DUT.
- [Ver] TG verification: Test ICMPv4 (or ICMPv6) Echo Request packets are sent in both directions by TG on links to DUT1 and via container; on receive TG verifies packets for correctness and their IPv4 (IPv6) src-addr, dst-addr and MAC addresses.pecifications:** RFC792
Name | VPP API Test Commands History - Commands Used Per Test Case |
---|---|
eth2p-ethip4-l2bdbase-eth-2memif-1dcr-device | No Data |
eth2p-ethip6-l2bdbase-eth-2memif-1dcr-device | No Data |
eth2p-eth-l2xcbase-eth-2memif-1dcr-dev¶
eth2p-eth-l2xcbase-eth-2memif-1dcr-dev¶
L2 cross-connect test cases with memif interface
- [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 for L2 switching of IPv4; Eth-IPv6-ICMPv6 for L2 switching of IPv6.
- [Cfg] DUT configuration: DUT1 is configured with L2 cross-connect (L2XC) switching. Container is connected to VPP via Memif interface. Container is running same VPP version as running on DUT.
- [Ver] TG verification: Test ICMPv4 (or ICMPv6) Echo Request packets are sent in both directions by TG on links to DUT1 and via container; on receive TG verifies packets for correctness and their IPv4 (IPv6) src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC792
Name | VPP API Test Commands History - Commands Used Per Test Case |
---|---|
eth2p-ethip4-l2xcbase-eth-2memif-1dcr-device | No Data |
eth2p-ethip6-l2xcbase-eth-2memif-1dcr-device | No Data |
eth2p-ethip4-ip4base-eth-2memif-1dcr-dev¶
eth2p-ethip4-ip4base-eth-2memif-1dcr-dev¶
IPv4 routing test cases with memif interface
- [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 for IPv4 routing on both links.
- [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /24 route entries. Container is connected to VPP via Memif interface. Container is running same VPP version as running on DUT.
- [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in one direction by TG on links to DUT1 and via container; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC791, RFC826, RFC792
Name | VPP API Test Commands History - Commands Used Per Test Case |
---|---|
eth2p-ethip4-ip4base-eth-2memif-1dcr-device | No Data |
eth2p-ethip6-ip6base-eth-2memif-1dcr-dev¶
eth2p-ethip6-ip6base-eth-2memif-1dcr-dev¶
IPv4 routing test cases with memif interface
- [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6-ICMPv6 for IPv6 routing on both links.
- [Cfg] DUT configuration: DUT1 is configured with IPv6 routing and two static IPv6 /64 route entries. Container is connected to VPP via Memif interface. Container is running same VPP version as running on DUT.
- [Ver] TG verification: Test ICMPv6 Echo Request packets are sent in one direction by TG on links to DUT1 and via container; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC791, RFC826, RFC792
Name | VPP API Test Commands History - Commands Used Per Test Case |
---|---|
eth2p-ethip6-ip6base-eth-2memif-1dcr-device | No Data |
ip4¶
eth2p-ethip4-ip4base-dev¶
eth2p-ethip4-ip4base-dev¶
IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 for IPv4 routing on both links.
- [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /24 route entries.
- [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in one direction by TG on links to DUT1; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC791, RFC826, RFC792
Name | VPP API Test Commands History - Commands Used Per Test Case |
---|---|
eth2p-ethicmpv4-ip4base-device_echo-req-to-dut-ingress-interface | No Data |
eth2p-ethicmpv4-ip4base-device_echo-req-to-dut-egress-interface | No Data |
eth2p-ethicmpv4-ip4base-device_echo-req-to-tg-interface-for-local-ipv4-address | No Data |
eth2p-ethicmpv4-ip4base-device_echo-req-to-tg-interface-for-remote-host-ipv4-address | No Data |
ip6¶
eth2p-ethip6-ip6base-dev¶
eth2p-ethip6-ip6base-dev¶
IPv6 routing test cases
- [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6-ICMPv6 for IPv6 routing on both links.
- [Cfg] DUT configuration: DUT1 is configured with IPv6 routing and two static IPv6 /64 route entries.
- [Ver] TG verification: Test ICMPv6 Echo Request packets are sent in one direction by TG on links to DUT1; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC2460, RFC4443, RFC4861
Name | VPP API Test Commands History - Commands Used Per Test Case |
---|---|
eth2p-ethicmpv6-ip6base-device_echo-req-to-dut-ingress-interface | No Data |
eth2p-ethicmpv6-ip6base-device_echo-req-to-dut-egress-interface | No Data |
eth2p-ethicmpv6-ip6base-device_echo-req-to-tg-interface-for-local-ipv4-address | No Data |
eth2p-ethicmpv6-ip6base-device_echo-req-to-tg-interface-for-remote-host-ipv4-address | No Data |
l2bd¶
eth2p-eth-l2bdbasemaclrn-dev¶
eth2p-eth-l2bdbasemaclrn-dev¶
L2 bridge-domain test cases
- [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 for L2 switching of IPv4; Eth-IPv6-ICMPv6 for L2 switching of IPv6 use. Both apply to all links.
- [Cfg] DUT configuration: DUT1 is configured with L2 bridge-domain switching.
- [Ver] TG verification: Test ICMPv4 (or ICMPv6) Echo Request packets are sent in both directions by TG on links to DUT1; on receive TG verifies packets for correctness and their IPv4 (IPv6) src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC792
Name | VPP API Test Commands History - Commands Used Per Test Case |
---|---|
eth2p-ethicmpv4-l2bdbase-device | No Data |
eth2p-ethicmpv6-l2bdbase-device | No Data |
l2xc¶
eth2p-ethicmp-l2xcbase-dev¶
eth2p-ethicmp-l2xcbase-dev¶
L2 cross-connect test cases
- [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 for L2 switching of IPv4; Eth-IPv6-ICMPv6 for L2 switching of IPv6 use. Both apply to all links.
- [Cfg] DUT configuration: DUT1 is configured with L2 cross-connect switching.
- [Ver] TG verification: Test ICMPv4 (or ICMPv6) Echo Request packets are sent in both directions by TG on links to DUT1; on receive TG verifies packets for correctness and their IPv4 (IPv6) src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC792
Name | VPP API Test Commands History - Commands Used Per Test Case |
---|---|
eth2p-ethicmpv4-l2xcbase-device | No Data |
eth2p-ethicmpv6-l2xcbase-device | No Data |
vm vhost¶
ip4¶
eth2p-ethip4-ip4base-eth-2vhost-1vm-dev¶
eth2p-ethip4-ip4base-eth-2vhost-1vm-dev¶
IPv4 routing test cases with vhost user interface
- [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with VM and single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 for IPv4 routing on both links.
- [Cfg] DUT configuration: DUT1 is configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is configured with linux bridge interconnecting vhost-user interfaces.
- [Ver] TG verification: Test ICMPv4 Echo Request packets are sent in one direction by TG on links to DUT1; on receive TG verifies packets for correctness and their IPv4 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC791, RFC826, RFC792
Name | VPP API Test Commands History - Commands Used Per Test Case |
---|---|
eth2p-ethip4-ip4base-eth-2vhost-1vm-device | No Data |
ip6¶
eth2p-ethip6-ip6base-eth-2vhost-1vm-dev¶
eth2p-ethip6-ip6base-eth-2vhost-1vm-dev¶
IPv4 routing test cases with vhost user interface
- [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with VM and single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6-ICMPv6 for IPv6 routing on both links.
- [Cfg] DUT configuration: DUT1 is configured with IPv6 routing and two static IPv6 /64 route entries. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is configured with linux bridge interconnecting vhost-user interfaces.
- [Ver] TG verification: Test ICMPv6 Echo Request packets are sent in one direction by TG on links to DUT1; on receive TG verifies packets for correctness and their IPv6 src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC2460, RFC4443, RFC4861
Name | VPP API Test Commands History - Commands Used Per Test Case |
---|---|
eth2p-ethip6-ip6base-eth-2vhost-1vm-device | No Data |
l2bd¶
eth2p-eth-l2bdbasemaclrn-eth-2vhost-1vm-dev¶
eth2p-eth-l2bdbasemaclrn-eth-2vhost-1vm-dev¶
L2 bridge-domain test cases with vhost user interface
- [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with VM and single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 for L2 switching of IPv4; Eth-IPv6-ICMPv6 for L2 switching of IPv6.
- [Cfg] DUT configuration: DUT1 is configured with two L2 bridge-domains (L2BD) switching combined with MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is configured with linux bridge interconnecting vhost-user interfaces.
- [Ver] TG verification: Test ICMPv4 (or ICMPv6) Echo Request packets are sent in both directions by TG on links to DUT1 via VM; on receive TG verifies packets for correctness and their IPv4 (IPv6) src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC792
Name | VPP API Test Commands History - Commands Used Per Test Case |
---|---|
eth2p-ethip4-l2bdbasemaclrn-eth-2vhost-1vm-device | No Data |
eth2p-ethip6-l2bdbasemaclrn-eth-2vhost-1vm-device | No Data |
l2xc¶
eth2p-eth-l2xcbase-eth-2vhost-1vm-dev¶
eth2p-eth-l2xcbase-eth-2vhost-1vm-dev¶
L2 cross-connect test cases with vhost user interface
- [Top] Network Topologies: TG-DUT1-TG 2-node circular topology with VM and single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-ICMPv4 for L2 switching of IPv4; Eth-IPv6-ICMPv6 for L2 switching of IPv6.
- [Cfg] DUT configuration: DUT1 is configured with L2 cross-connect (L2XC) switching. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is configured with linux bridge interconnecting vhost-user interfaces.
- [Ver] TG verification: Test ICMPv4 (or ICMPv6) Echo Request packets are sent in both directions by TG on links to DUT1 via VM; on receive TG verifies packets for correctness and their IPv4 (IPv6) src-addr, dst-addr and MAC addresses.
- [Ref] Applicable standard specifications: RFC792
Name | VPP API Test Commands History - Commands Used Per Test Case |
---|---|
eth2p-ethip4-l2xcbase-eth-2vhost-1vm-device | No Data |
eth2p-ethip6-l2xcbase-eth-2vhost-1vm-device | No Data |