container memif¶
10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr¶
RFC2544: Pkt throughput L2BD with memif and IEEE 802.1Q test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 bridge domain. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with two L2 bridge domains and MAC learning enabled. Container is connected to VPP via Memif interface. Container is running same VPP version as running on DUT. Container is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory constraints. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr |
|
64b-4t2c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr |
|
64b-8t4c-dot1q-l2bdbasemaclrn-eth-2memif-1dcr-ndrpdr | Minimal rate loss fraction 0.00713664287786 does not reach target 0.005. 4282 packets lost. |
10ge2p1x710-eth-l2bdbasemaclrn-eth-2memif-1lxc-ndrpdr¶
RFC2544: Pkt throughput L2BD test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 bridge domain.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with two L2 bridge domains and MAC learning enabled. LXC is connected to VPP via Memif interface. LXC is running same VPP version as running on DUT. LXC is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory constraints. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-eth-l2bdbasemaclrn-eth-2memif-1lxc-ndrpdr |
|
64b-4t2c-eth-l2bdbasemaclrn-eth-2memif-1lxc-ndrpdr |
|
64b-8t4c-eth-l2bdbasemaclrn-eth-2memif-1lxc-ndrpdr | Minimal rate loss fraction 0.00405165316116 does not reach target 0.0. 2431 packets lost. |
imix-2t1c-eth-l2bdbasemaclrn-eth-2memif-1lxc-ndrpdr |
|
imix-4t2c-eth-l2bdbasemaclrn-eth-2memif-1lxc-ndrpdr |
|
imix-8t4c-eth-l2bdbasemaclrn-eth-2memif-1lxc-ndrpdr |
|
10ge2p1x710-eth-l2xcbase-eth-1memif-1dcr-ndrpdr¶
RFC2544: Pkt throughput L2XC test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
- [Cfg] DUT configuration: DUT1 and DUT2 configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. Container is connected to VPP via Memif interface running same VPP version as running on DUT. Resources are limited via cgroup to use 5 cores allocated from pool of isolated CPUs. There are no memory contraints. Cross Horizontal topology with packets flowing via DUT (VPP) to Container, then via horizontal memif to the next Container, and so on until the last Container then to NIC (in last Container). Single Container is supported as of now.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-eth-l2xcbase-eth-1memif-1dcr-ndrpdr |
|
64b-4t2c-eth-l2xcbase-eth-1memif-1dcr-ndrpdr |
|
64b-8t4c-eth-l2xcbase-eth-1memif-1dcr-ndrpdr |
|
imix-2t1c-eth-l2xcbase-eth-1memif-1dcr-ndrpdr |
|
imix-4t2c-eth-l2xcbase-eth-1memif-1dcr-ndrpdr |
|
imix-8t4c-eth-l2xcbase-eth-1memif-1dcr-ndrpdr |
|
10ge2p1x710-eth-l2xcbase-eth-2memif-1dcr-ndrpdr¶
RFC2544: Pkt throughput L2XC test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. Container is connected to VPP via Memif interface. Container is running same VPP version as running on DUT. Container is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory contraints.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-eth-l2xcbase-eth-2memif-1dcr-ndrpdr |
|
64b-4t2c-eth-l2xcbase-eth-2memif-1dcr-ndrpdr |
|
64b-8t4c-eth-l2xcbase-eth-2memif-1dcr-ndrpdr |
|
imix-2t1c-eth-l2xcbase-eth-2memif-1dcr-ndrpdr |
|
imix-4t2c-eth-l2xcbase-eth-2memif-1dcr-ndrpdr |
|
imix-8t4c-eth-l2xcbase-eth-2memif-1dcr-ndrpdr |
|
10ge2p1x710-eth-l2xcbase-eth-2memif-1lxc-ndrpdr¶
RFC2544: Pkt throughput L2XC test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel. LXC is connected to VPP via Memif interface. LXC is running same VPP version as running on DUT. LXC is limited via cgroup to use 3 cores allocated from pool of isolated CPUs. There are no memory contraints.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-eth-l2xcbase-eth-2memif-1lxc-ndrpdr |
|
64b-4t2c-eth-l2xcbase-eth-2memif-1lxc-ndrpdr |
|
64b-8t4c-eth-l2xcbase-eth-2memif-1lxc-ndrpdr |
|
imix-2t1c-eth-l2xcbase-eth-2memif-1lxc-ndrpdr |
|
imix-4t2c-eth-l2xcbase-eth-2memif-1lxc-ndrpdr |
|
imix-8t4c-eth-l2xcbase-eth-2memif-1lxc-ndrpdr |
|
10ge2p1x710-ethip4-ip4base-eth-2memif-1dcr-ndrpdr¶
RFC2544: Pkt throughput IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing with two FIB tables and two static IPv4 /24 route entries per FIB table. Container is connected to VPP via Memif interface. Container is running same VPP version as running on DUT. Container is limited via cgroup to use cores allocated from pool of isolated CPUs. There are no memory contraints. DUTs are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance and throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4base-eth-2memif-1dcr-ndrpdr |
|
64b-4t2c-ethip4-ip4base-eth-2memif-1dcr-ndrpdr |
|
64b-8t4c-ethip4-ip4base-eth-2memif-1dcr-ndrpdr |
|
imix-2t1c-ethip4-ip4base-eth-2memif-1dcr-ndrpdr |
|
imix-4t2c-ethip4-ip4base-eth-2memif-1dcr-ndrpdr |
|
imix-8t4c-ethip4-ip4base-eth-2memif-1dcr-ndrpdr |
|
ip4¶
10ge2p1x710-avf-eth-ip4base-ndrpdr¶
RFC2544: Pkt throughput IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel with VF enabled.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-avf-eth-ip4base-ndrpdr |
|
64b-4t2c-avf-eth-ip4base-ndrpdr |
|
64b-8t4c-avf-eth-ip4base-ndrpdr |
|
10ge2p1x710-dot1q-ip4base-ndrpdr¶
RFC2544: Pkt throughput IPv4 routing with IEEE 802.1Q test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /30 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-dot1q-ip4base-ndrpdr |
|
64b-4t2c-dot1q-ip4base-ndrpdr |
|
64b-8t4c-dot1q-ip4base-ndrpdr |
|
10ge2p1x710-ethip4-ip4base-copwhtlistbase-ndrpdr¶
RFC2544: Pkt throughput IPv4 whitelist test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 COP security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4base-copwhtlistbase-ndrpdr |
|
64b-4t2c-ethip4-ip4base-copwhtlistbase-ndrpdr |
|
64b-8t4c-ethip4-ip4base-copwhtlistbase-ndrpdr |
|
10ge2p1x710-ethip4-ip4base-iacldstbase-ndrpdr¶
RFC2544: Pkt throughput IPv4 iAcl whitelist test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 iAcl security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4base-iacldstbase-ndrpdr |
|
64b-4t2c-ethip4-ip4base-iacldstbase-ndrpdr |
|
64b-8t4c-ethip4-ip4base-iacldstbase-ndrpdr |
|
10ge2p1x710-ethip4-ip4base-ipolicemarkbase-ndrpdr¶
RFC2544: Pkt throughput IPv4 policer test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries and policer with 2R3C color-aware configuration. Policer is applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544, RFC2698.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4base-ipolicemarkbase-ndrpdr |
|
64b-4t2c-ethip4-ip4base-ipolicemarkbase-ndrpdr |
|
64b-8t4c-ethip4-ip4base-ipolicemarkbase-ndrpdr |
|
10ge2p1x710-ethip4-ip4base-ndrpdr¶
RFC2544: Pkt throughput IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4base-ndrpdr |
|
64b-4t2c-ethip4-ip4base-ndrpdr |
|
64b-8t4c-ethip4-ip4base-ndrpdr |
|
10ge2p1x710-ethip4-ip4scale200k-ndrpdr¶
RFC2544: Pkt throughput IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4scale200k-ndrpdr |
|
64b-4t2c-ethip4-ip4scale200k-ndrpdr |
|
64b-8t4c-ethip4-ip4scale200k-ndrpdr |
|
10ge2p1x710-ethip4-ip4scale20k-ndrpdr¶
RFC2544: Pkt throughput IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4scale20k-ndrpdr |
|
64b-4t2c-ethip4-ip4scale20k-ndrpdr |
|
64b-8t4c-ethip4-ip4scale20k-ndrpdr |
|
10ge2p1x710-ethip4-ip4scale2m-ndrpdr¶
RFC2544: Pkt throughput IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4scale2m-ndrpdr |
|
64b-4t2c-ethip4-ip4scale2m-ndrpdr |
|
64b-8t4c-ethip4-ip4scale2m-ndrpdr |
|
10ge2p1x710-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr¶
RFC2544: Pkt throughput IPv4 test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 Niantic by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr |
|
64b-4t2c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr |
|
64b-8t4c-ethip4udp-ip4base-iacl1sf-10kflows-ndrpdr |
|
10ge2p1x710-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr¶
RFC2544: Pkt throughput IPv4 test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 Niantic by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr |
|
64b-4t2c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr |
|
64b-8t4c-ethip4udp-ip4base-iacl1sl-10kflows-ndrpdr |
|
10ge2p1x710-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr¶
RFC2544: Pkt throughput IPv4 test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 Niantic by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr |
|
64b-4t2c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr |
|
64b-8t4c-ethip4udp-ip4base-iacl50sf-10kflows-ndrpdr |
|
10ge2p1x710-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr¶
RFC2544: Pkt throughput IPv4 test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and one static IPv4 /24 route entries. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 Niantic by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr |
|
64b-4t2c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr |
|
64b-8t4c-ethip4udp-ip4base-iacl50sl-10kflows-ndrpdr |
|
10ge2p1x710-ethip4udp-ip4base-nat44-ndrpdr¶
RFC2544: Pkt throughput NAT44 performance test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4udp-ip4base-nat44-ndrpdr |
|
64b-4t2c-ethip4udp-ip4base-nat44-ndrpdr |
|
64b-8t4c-ethip4udp-ip4base-nat44-ndrpdr |
|
10ge2p1x710-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr¶
RFC2544: Pkt throughput NAT44 performance test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr |
|
64b-4t2c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr |
|
64b-8t4c-ethip4udp-ip4scale1000-udpsrcscale15-nat44-ndrpdr |
|
25ge2p1xxv710-avf-eth-ip4base-ndrpdr¶
RFC2544: Pkt throughput IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p25GE NIC XXV710 by Intel with VF enabled.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-avf-eth-ip4base-ndrpdr |
|
64b-4t2c-avf-eth-ip4base-ndrpdr |
|
64b-8t4c-avf-eth-ip4base-ndrpdr |
|
ip4 tunnels¶
10ge2p1x710-dot1q–ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr¶
RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-Dot1Q-IPv4 for L2 switching of IPv4 on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with 100 L2 bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, up to 64,5k flows per flow-group) with all packets containing Ethernet header, IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name | Status |
---|---|
64b-2t1c-dot1q–ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr |
|
64b-4t2c-dot1q–ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr |
|
64b-8t4c-dot1q–ethip4vxlan-l2bdscale100l2bd100vlan100vxlan-ndrpdr |
|
10ge2p1x710-dot1q–ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr¶
RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-Dot1Q-IPv4 for L2 switching of IPv4 on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with 10 L2 bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, up to 64,5k flows per flow-group) with all packets containing Ethernet header, IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name | Status |
---|---|
64b-2t1c-dot1q–ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr |
|
64b-4t2c-dot1q–ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr |
|
64b-8t4c-dot1q–ethip4vxlan-l2bdscale10l2bd10vlan10vxlan-ndrpdr |
|
10ge2p1x710-dot1q–ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr¶
RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-Dot1Q-IPv4 for L2 switching of IPv4 on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with 1k L2 bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, up to 64,5k flows per flow-group) with all packets containing Ethernet header, IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name | Status |
---|---|
64b-2t1c-dot1q–ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr |
|
64b-4t2c-dot1q–ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr |
|
64b-8t4c-dot1q–ethip4vxlan-l2bdscale1kl2bd1kvlan1kvxlan-ndrpdr |
|
10ge2p1x710-dot1q–ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr¶
RFC2544: Pkt throughput L2BD with IEEE 802.1Q and VXLANoIPv4 test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-Dot1Q-IPv4 for L2 switching of IPv4 on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with 1 L2 bridge domains. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, up to 64,5k flows per flow-group) with all packets containing Ethernet header, IEEE 802.1Q header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name | Status |
---|---|
64b-2t1c-dot1q–ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr |
|
64b-4t2c-dot1q–ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr |
|
64b-8t4c-dot1q–ethip4vxlan-l2bdscale1l2bd1vlan1vxlan-ndrpdr |
|
10ge2p1x710-ethip4lispip4-ip4base-ndrpdr¶
RFC2544: Pkt throughput Lisp test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv4 on DUT1-DUT2, Eth-IPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC6830.
Name | Status |
---|---|
64b-2t1c-ethip4lispip4-ip4base-ndrpdr |
|
64b-4t2c-ethip4lispip4-ip4base-ndrpdr |
|
64b-8t4c-ethip4lispip4-ip4base-ndrpdr |
|
10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-ndrpdr¶
RFC2544: Pkt throughput L2BD with VXLANoIPv4 test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4 on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUTs.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name | Status |
---|---|
64b-2t1c-ethip4vxlan-l2bdbasemaclrn-ndrpdr |
|
64b-4t2c-ethip4vxlan-l2bdbasemaclrn-ndrpdr |
|
64b-8t4c-ethip4vxlan-l2bdbasemaclrn-ndrpdr |
|
10ge2p1x710-ethip4vxlan-l2xcbase-ndrpdr¶
RFC2544: Pkt throughput L2XC with VXLANoIPv4 test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross-connect on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. VXLAN tunnels are configured between L2XCs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name | Status |
---|---|
64b-2t1c-ethip4vxlan-l2xcbase-ndrpdr |
|
64b-4t2c-ethip4vxlan-l2xcbase-ndrpdr |
|
64b-8t4c-ethip4vxlan-l2xcbase-ndrpdr |
|
ip6¶
10ge2p1x710-ethip6-ip6base-copwhtlistbase-ndrpdr¶
RFC2544: Pkt throughput IPv6 whitelist test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 COP security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
78b-2t1c-ethip6-ip6base-copwhtlistbase-ndrpdr |
|
78b-4t2c-ethip6-ip6base-copwhtlistbase-ndrpdr |
|
78b-8t4c-ethip6-ip6base-copwhtlistbase-ndrpdr |
|
10ge2p1x710-ethip6-ip6base-iacldstbase-ndrpdr¶
RFC2544: Pkt throughput IPv6 iAcl whitelist test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 iAcl security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
78b-2t1c-ethip6-ip6base-iacldstbase-ndrpdr |
|
78b-4t2c-ethip6-ip6base-iacldstbase-ndrpdr |
|
78b-8t4c-ethip6-ip6base-iacldstbase-ndrpdr |
|
10ge2p1x710-ethip6-ip6base-ndrpdr¶
RFC2544: Pkt throughput IPv6 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
78b-2t1c-ethip6-ip6base-ndrpdr |
|
78b-4t2c-ethip6-ip6base-ndrpdr |
|
78b-8t4c-ethip6-ip6base-ndrpdr |
|
10ge2p1x710-ethip6-ip6scale200k-ndrpdr¶
RFC2544: Pkt throughput IPv6 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x100k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
78b-2t1c-ethip6-ip6scale200k-ndrpdr |
|
78b-4t2c-ethip6-ip6scale200k-ndrpdr |
|
78b-8t4c-ethip6-ip6scale200k-ndrpdr |
|
10ge2p1x710-ethip6-ip6scale20k-ndrpdr¶
RFC2544: Pkt throughput IPv6 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
78b-2t1c-ethip6-ip6scale20k-ndrpdr |
|
78b-4t2c-ethip6-ip6scale20k-ndrpdr |
|
78b-8t4c-ethip6-ip6scale20k-ndrpdr |
|
10ge2p1x710-ethip6-ip6scale2m-ndrpdr¶
RFC2544: Pkt throughput IPv6 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x1M static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv6 header with IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
78b-2t1c-ethip6-ip6scale2m-ndrpdr |
|
78b-4t2c-ethip6-ip6scale2m-ndrpdr |
|
78b-8t4c-ethip6-ip6scale2m-ndrpdr |
|
l2¶
10ge2p1x710-avf-eth-l2bdbasemaclrn-ndrpdr¶
RFC2544: Pkt throughput L2BD test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 bridge-domain.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel with VF enabled.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-avf-eth-l2bdbasemaclrn-ndrpdr |
|
64b-4t2c-avf-eth-l2bdbasemaclrn-ndrpdr |
|
64b-8t4c-avf-eth-l2bdbasemaclrn-ndrpdr |
|
10ge2p1x710-avf-eth-l2patch-ndrpdr¶
RFC2544: Pkt throughput L2patch test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 patch DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel with VF enabled.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-avf-eth-l2patch-ndrpdr | Minimal rate loss fraction 1.0 does not reach target 0.005. Zero packets forwarded! |
64b-4t2c-avf-eth-l2patch-ndrpdr | Minimal rate loss fraction 1.0 does not reach target 0.005. Zero packets forwarded! |
64b-8t4c-avf-eth-l2patch-ndrpdr | Minimal rate loss fraction 1.0 does not reach target 0.005. Zero packets forwarded! |
10ge2p1x710-avf-eth-l2xcbase-ndrpdr¶
RFC2544: Pkt throughput L2XC test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross-connect.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel with VF enabled.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-avf-eth-l2xcbase-ndrpdr |
|
64b-4t2c-avf-eth-l2xcbase-ndrpdr |
|
64b-8t4c-avf-eth-l2xcbase-ndrpdr |
|
10ge2p1x710-dot1q-l2bdbasemaclrn-ndrpdr¶
RFC2544: Pkt throughput L2BD with IEEE 802.1Q test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge domain and MAC learning enabled. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-dot1q-l2bdbasemaclrn-ndrpdr |
|
64b-4t2c-dot1q-l2bdbasemaclrn-ndrpdr |
|
64b-8t4c-dot1q-l2bdbasemaclrn-ndrpdr |
|
10ge2p1x710-dot1q-l2xcbase-ndrpdr¶
RFC2544: Pkt throughput L2XC with IEEE 802.1Q test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-dot1q-l2xcbase-ndrpdr |
|
64b-4t2c-dot1q-l2xcbase-ndrpdr |
|
64b-8t4c-dot1q-l2xcbase-ndrpdr |
|
10ge2p1x710-eth-l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr¶
RFC2544: Pkt throughput L2BD test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr |
|
64b-4t2c-eth-l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr |
|
64b-8t4c-eth-l2bdbasemaclrn-iacl1sf-10kflows-ndrpdr |
|
10ge2p1x710-eth-l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr¶
RFC2544: Pkt throughput L2BD test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr |
|
64b-4t2c-eth-l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr |
|
64b-8t4c-eth-l2bdbasemaclrn-iacl1sl-10kflows-ndrpdr |
|
10ge2p1x710-eth-l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr¶
RFC2544: Pkt throughput L2BD test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr |
|
64b-4t2c-eth-l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr |
|
64b-8t4c-eth-l2bdbasemaclrn-iacl50sf-10kflows-ndrpdr |
|
10ge2p1x710-eth-l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr¶
RFC2544: Pkt throughput L2BD test cases with ACL
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 is configured with L2 bridge domain and MAC learning enabled. DUT2 is configured with L2 cross-connects. Required ACL rules are applied to input paths of both DUT1 intefaces. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr |
|
64b-4t2c-eth-l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr |
|
64b-8t4c-eth-l2bdbasemaclrn-iacl50sl-10kflows-ndrpdr |
|
10ge2p1x710-eth-l2bdbasemaclrn-ndrpdr¶
RFC2544: Pkt throughput L2BD test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdbasemaclrn-ndrpdr |
|
64b-4t2c-eth-l2bdbasemaclrn-ndrpdr |
|
64b-8t4c-eth-l2bdbasemaclrn-ndrpdr |
|
10ge2p1x710-eth-l2bdscale100kmaclrn-ndrpdr¶
RFC2544: Pkt throughput for L2BD test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 50k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdscale100kmaclrn-ndrpdr |
|
64b-4t2c-eth-l2bdscale100kmaclrn-ndrpdr |
|
64b-8t4c-eth-l2bdscale100kmaclrn-ndrpdr |
|
10ge2p1x710-eth-l2bdscale10kmaclrn-ndrpdr¶
RFC2544: Pkt throughput for L2BD test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 5k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdscale10kmaclrn-ndrpdr |
|
64b-4t2c-eth-l2bdscale10kmaclrn-ndrpdr |
|
64b-8t4c-eth-l2bdscale10kmaclrn-ndrpdr |
|
10ge2p1x710-eth-l2bdscale1mmaclrn-ndrpdr¶
RFC2544: Pkt throughput for L2BD test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 500k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses ranges are incremented as follows: port01_src ca:fe:00:00:00:00 - port01_src ca:fe:00:07:a1:1f, port01_dst fa:ce:00:00:00:00 - port01_dst fa:ce:00:07:a1:1f, port02_src fa:ce:00:00:00:00 - port02_src fa:ce:00:07:a1:1f, port02_dst ca:fe:00:00:00:00 - port02_dst ca:fe:00:07:a1:1f
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdscale1mmaclrn-ndrpdr |
|
64b-4t2c-eth-l2bdscale1mmaclrn-ndrpdr |
|
64b-8t4c-eth-l2bdscale1mmaclrn-ndrpdr |
|
10ge2p1x710-eth-l2patch-ndrpdr¶
RFC2544: Pkt throughput L2patch test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 patch DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header,IPv4 header with static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2patch-ndrpdr |
|
64b-4t2c-eth-l2patch-ndrpdr |
|
64b-8t4c-eth-l2patch-ndrpdr |
|
10ge2p1x710-eth-l2xcbase-ndrpdr¶
RFC2544: Pkt throughput L2XC test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2xcbase-ndrpdr |
|
64b-4t2c-eth-l2xcbase-ndrpdr |
|
64b-8t4c-eth-l2xcbase-ndrpdr |
|
25ge2p1xxv710-avf-eth-l2bdbasemaclrn-ndrpdr¶
RFC2544: Pkt throughput L2BD test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 bridge-domain.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p25GE NIC XXV710 by Intel with VF enabled.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-avf-eth-l2bdbasemaclrn-ndrpdr |
|
64b-4t2c-avf-eth-l2bdbasemaclrn-ndrpdr |
|
64b-8t4c-avf-eth-l2bdbasemaclrn-ndrpdr |
|
25ge2p1xxv710-avf-eth-l2patch-ndrpdr¶
RFC2544: Pkt throughput L2patch test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 patch DUT1 and DUT2 tested with 2p25GE NIC XXV710 by Intel with VF enabled.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-avf-eth-l2patch-ndrpdr | Minimal rate loss fraction 1.0 does not reach target 0.005. Zero packets forwarded! |
64b-4t2c-avf-eth-l2patch-ndrpdr | Minimal rate loss fraction 1.0 does not reach target 0.005. Zero packets forwarded! |
64b-8t4c-avf-eth-l2patch-ndrpdr | Minimal rate loss fraction 1.0 does not reach target 0.005. Zero packets forwarded! |
25ge2p1xxv710-avf-eth-l2xcbase-ndrpdr¶
RFC2544: Pkt throughput L2XC test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross-connect.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p25GE NIC XXV710 by Intel with VF enabled.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-avf-eth-l2xcbase-ndrpdr |
|
64b-4t2c-avf-eth-l2xcbase-ndrpdr |
|
64b-8t4c-avf-eth-l2xcbase-ndrpdr |
|
25ge2p1xxv710-eth-l2patch-ndrpdr¶
RFC2544: Pkt throughput L2patch test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 patch.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 patch DUT1 and DUT2 tested with 2p25GE NIC XXV710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header,IPv4 header with static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2patch-ndrpdr |
|
64b-4t2c-eth-l2patch-ndrpdr |
|
64b-8t4c-eth-l2patch-ndrpdr |
|
vm vhost¶
10ge2p1x710-1lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr¶
RFC2544: Pkt throughput L2BD test cases with vhost and vpp link bonding
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with VPP link bonding (mode LACP, transmit policy l34) on link between DUT1 and DUT2 and L2 bridge-domain with MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 Fortville by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-1lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-4t2c-1lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-8t4c-1lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.953880153733 does not reach target 0.005. 572330 packets lost. |
imix-2t1c-1lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-4t2c-1lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-8t4c-1lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.72190592698 does not reach target 0.005. 433145 packets lost. |
10ge2p1x710-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr¶
RFC2544: Pkt throughput L2XC test cases with vhost and vpp link bonding
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with VPP link bonding (mode LACP, transmit policy l34) on link between DUT1 and DUT2 and L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 Fortville by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-4t2c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-8t4c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.977853407155 does not reach target 0.005. 586714 packets lost. |
imix-2t1c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-4t2c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-8t4c-1lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.794015686614 does not reach target 0.005. 476411 packets lost. |
10ge2p1x710-2lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr¶
RFC2544: Pkt throughput L2BD test cases with vhost and vpp link bonding
- [Top] Network Topologies: TG-DUT1=DUT2-TG 3-node circular topology with single links between TG and DUT nodes and double link between DUT nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with VPP link bonding (mode LACP, transmit policy l34) on link between DUT1 and DUT2 and L2 bridge-domain with MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 Fortville by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-2lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-4t2c-2lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-8t4c-2lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.261266666667 does not reach target 0.005. 156760 packets lost. |
imix-2t1c-2lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-4t2c-2lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-8t4c-2lbvpplacp-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.675564414785 does not reach target 0.005. 405340 packets lost. |
10ge2p1x710-2lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr¶
RFC2544: Pkt throughput L2XC test cases with vhost and vpp link bonding
- [Top] Network Topologies: TG-DUT1=DUT2-TG 3-node circular topology with single links between TG and DUT nodes and double link between DUT nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with VPP link bonding (mode LACP, transmit policy l34) on link between DUT1 and DUT2 and L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 Fortville by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-2lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-4t2c-2lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-8t4c-2lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.248389172036 does not reach target 0.005. 149034 packets lost. |
imix-2t1c-2lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-4t2c-2lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-8t4c-2lbvpplacp-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.671342762191 does not reach target 0.005. 402807 packets lost. |
10ge2p1x710-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr¶
RFC2544: Pkt throughput L2BD with vhost abd IEEE 802.1Q test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. IEEE 802.1Q tagging is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces, forwarding mode is set to io, rxd/txd=1024. DUT1 and DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-4t2c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-8t4c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.814663333333 does not reach target 0.005. 488798 packets lost. |
imix-2t1c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-4t2c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-8t4c-dot1q-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.74754 does not reach target 0.005. 448524 packets lost. |
10ge2p1x710-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr¶
RFC2544: Pkt throughput L2XC test cases with vhost
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-4t2c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-8t4c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.891195362682 does not reach target 0.005. 534719 packets lost. |
imix-2t1c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-4t2c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-8t4c-dot1q-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.712867623775 does not reach target 0.005. 427722 packets lost. |
10ge2p1x710-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr¶
RFC2544: Pkt throughput L2BD test cases with vhost
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus on NUMA1 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
Name | Status |
---|---|
64b-2t1c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-4t2c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-8t4c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.09871300429 does not reach target 0.005. 59228 packets lost. |
imix-2t1c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-4t2c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-8t4c-eth-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.550588164706 does not reach target 0.005. 330354 packets lost. |
10ge2p1x710-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-ndrpdr¶
RFC2544: Pkt throughput L2BD test cases with vhost
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domains and MAC learning enabled. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 6-10 and 11-15 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-ndrpdr |
|
64b-4t2c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-ndrpdr |
|
64b-8t4c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-ndrpdr | Minimal rate loss fraction 0.182398333333 does not reach target 0.005. 109439 packets lost. |
imix-2t1c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-ndrpdr |
|
imix-4t2c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-ndrpdr |
|
imix-8t4c-eth-l2bdbasemaclrn-eth-4vhostvr1024-2vm-ndrpdr | Minimal rate loss fraction 0.759005 does not reach target 0.005. 455403 packets lost. |
10ge2p1x710-eth-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr¶
RFC2544: Pkt throughput L2XC test cases with vhost
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-eth-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-4t2c-eth-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-8t4c-eth-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.21296595678 does not reach target 0.005. 127780 packets lost. |
imix-2t1c-eth-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-4t2c-eth-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-8t4c-eth-l2xcbase-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.634132886224 does not reach target 0.005. 380481 packets lost. |
10ge2p1x710-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrpdr¶
RFC2544: Pkt throughput L2XC test cases with vhost
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connects. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 6-10 and 11-15 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrpdr |
|
64b-4t2c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrpdr |
|
64b-8t4c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrpdr | Minimal rate loss fraction 0.166136666667 does not reach target 0.005. 99682 packets lost. |
imix-2t1c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrpdr |
|
imix-4t2c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrpdr |
|
imix-8t4c-eth-l2xcbase-eth-4vhostvr1024-2vm-ndrpdr | Minimal rate loss fraction 0.260956666667 does not reach target 0.005. 156574 packets lost. |
10ge2p1x710-ethip4-ip4base-eth-2vhostvr1024-1vm-ndrpdr¶
RFC2544: Pkt throughput IPv4 test cases with vhost
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to mac, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4base-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-4t2c-ethip4-ip4base-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-8t4c-ethip4-ip4base-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.606381312062 does not reach target 0.005. 363830 packets lost. |
imix-2t1c-ethip4-ip4base-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-4t2c-ethip4-ip4base-eth-2vhostvr1024-1vm-ndrpdr |
|
imix-8t4c-ethip4-ip4base-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.583573054756 does not reach target 0.005. 350145 packets lost. |
10ge2p1x710-ethip4-ip4base-eth-4vhostvr1024-2vm-ndrpdr¶
RFC2544: Pkt throughput IPv4 test cases with vhost
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guests are connected to VPP via vhost-user interfaces. Guests are running DPDK testpmd interconnectingvhost-user interfaces using 5 cores pinned to cpus 6-10 and 11-15 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
Name | Status |
---|---|
64b-2t1c-ethip4-ip4base-eth-4vhostvr1024-2vm-ndrpdr |
|
64b-4t2c-ethip4-ip4base-eth-4vhostvr1024-2vm-ndrpdr |
|
64b-8t4c-ethip4-ip4base-eth-4vhostvr1024-2vm-ndrpdr | Minimal rate loss fraction 0.167555 does not reach target 0.005. 100533 packets lost. |
imix-2t1c-ethip4-ip4base-eth-4vhostvr1024-2vm-ndrpdr |
|
imix-4t2c-ethip4-ip4base-eth-4vhostvr1024-2vm-ndrpdr |
|
imix-8t4c-ethip4-ip4base-eth-4vhostvr1024-2vm-ndrpdr | Minimal rate loss fraction 0.579646666667 does not reach target 0.005. 347788 packets lost. |
10ge2p1x710-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr¶
RFC2544: Pkt throughput L2BD test cases with VXLANoIPv4 and vhost
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=1024, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using MLRsearch library. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 254 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC7348.
Name | Status |
---|---|
64b-2t1c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-4t2c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr |
|
64b-8t4c-ethip4vxlan-l2bdbasemaclrn-eth-2vhostvr1024-1vm-ndrpdr | Minimal rate loss fraction 0.710360965463 does not reach target 0.005. 426218 packets lost. |