7.1.2. IPv4 Routed-Forwarding¶
7.1.2.1. 10ge2p1x520-ethip4-ip4base-copwhtlistbase-ndrpdrdisc¶
RFC2544: Pkt throughput IPv4 whitelist test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 COP security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
| Name | Documentation | Status |
|---|---|---|
| tc01-64B-1t1c-ethip4-ip4base-copwhtlistbase-ndrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 8976190.25 pps (2x 4488095.125 pps) FINAL_BANDWIDTH: 6.031999848 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/1498/1656’, ‘20/1521/1648’] LAT_50%NDR: [‘10/27/92’, ‘10/27/131’] LAT_10%NDR: [‘10/21/54’, ‘10/20/48’] |
| tc02-64B-1t1c-ethip4-ip4base-copwhtlistbase-pdrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. |
FINAL_RATE: 9207142.625 pps (2x 4603571.3125 pps) FINAL_BANDWIDTH: 6.187199844 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/1555/1710’, ‘30/1505/1659’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc03-1518B-1t1c-ethip4-ip4base-copwhtlistbase-ndrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/299/322’, ‘20/350/386’] LAT_50%NDR: [‘20/15/205’, ‘20/14/207’] LAT_10%NDR: [‘20/26/57’, ‘20/28/58’] |
| tc04-1518B-1t1c-ethip4-ip4base-copwhtlistbase-pdrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/346/371’, ‘20/370/420’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc05-9000B-1t1c-ethip4-ip4base-copwhtlistbase-ndrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘60/304/371’, ‘60/273/362’] LAT_50%NDR: [‘50/65/142’, ‘50/65/136’] LAT_10%NDR: [‘50/61/97’, ‘50/55/72’] |
| tc06-9000B-1t1c-ethip4-ip4base-copwhtlistbase-pdrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘50/297/345’, ‘50/308/372’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc07-64B-2t2c-ethip4-ip4base-copwhtlistbase-ndrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 16828571.0 pps (2x 8414285.5 pps) FINAL_BANDWIDTH: 11.308799712 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/797/934’, ‘20/792/890’] LAT_50%NDR: [‘10/31/97’, ‘10/26/67’] LAT_10%NDR: [‘10/21/65’, ‘10/19/111’] |
| tc08-64B-2t2c-ethip4-ip4base-copwhtlistbase-pdrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. |
FINAL_RATE: 16828571.0 pps (2x 8414285.5 pps) FINAL_BANDWIDTH: 11.308799712 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘10/794/939’, ‘20/792/871’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc09-1518B-2t2c-ethip4-ip4base-copwhtlistbase-ndrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/76/110’, ‘20/380/439’] LAT_50%NDR: [‘20/26/59’, ‘10/26/142’] LAT_10%NDR: [‘20/26/50’, ‘20/27/174’] |
| tc10-1518B-2t2c-ethip4-ip4base-copwhtlistbase-pdrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/56/73’, ‘20/360/413’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc11-9000B-2t2c-ethip4-ip4base-copwhtlistbase-ndrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘50/345/421’, ‘50/84/132’] LAT_50%NDR: [‘50/63/200’, ‘50/66/92’] LAT_10%NDR: [‘50/61/148’, ‘50/62/97’] |
| tc12-9000B-2t2c-ethip4-ip4base-copwhtlistbase-pdrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘60/218/296’, ‘50/207/283’] LOSS_ACCEPTANCE: 0.5 percentage |
7.1.2.2. 10ge2p1x520-ethip4-ip4base-iacldstbase-ndrpdrdisc¶
RFC2544: Pkt throughput IPv4 iAcl whitelist test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 iAcl security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
| Name | Documentation | Status |
|---|---|---|
| tc01-64B-1t1c-ethip4-ip4base-iacldstbase-ndrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 8283333.125 pps (2x 4141666.5625 pps) FINAL_BANDWIDTH: 5.56639986 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/148/349’, ‘10/154/286’] LAT_50%NDR: [‘10/48/113’, ‘20/45/140’] LAT_10%NDR: [‘10/23/469’, ‘10/23/468’] |
| tc02-64B-1t1c-ethip4-ip4base-iacldstbase-pdrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. |
FINAL_RATE: 8283333.125 pps (2x 4141666.5625 pps) FINAL_BANDWIDTH: 5.56639986 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘10/143/309’, ‘20/160/312’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc03-1518B-1t1c-ethip4-ip4base-iacldstbase-ndrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/161/351’, ‘20/169/370’] LAT_50%NDR: [‘20/30/174’, ‘20/30/186’] LAT_10%NDR: [‘20/27/79’, ‘20/27/79’] |
| tc04-1518B-1t1c-ethip4-ip4base-iacldstbase-pdrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/297/325’, ‘20/359/410’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc05-9000B-1t1c-ethip4-ip4base-iacldstbase-ndrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘50/281/547’, ‘50/273/546’] LAT_50%NDR: [‘50/66/196’, ‘50/66/219’] LAT_10%NDR: [‘50/62/104’, ‘50/61/91’] |
| tc06-9000B-1t1c-ethip4-ip4base-iacldstbase-pdrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘50/273/298’, ‘60/311/364’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc07-64B-2t2c-ethip4-ip4base-iacldstbase-ndrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 14519047.25 pps (2x 7259523.625 pps) FINAL_BANDWIDTH: 9.756799752 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/916/1048’, ‘10/435/502’] LAT_50%NDR: [‘10/25/65’, ‘10/25/52’] LAT_10%NDR: [‘10/21/168’, ‘10/18/32’] |
| tc08-64B-2t2c-ethip4-ip4base-iacldstbase-pdrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. |
FINAL_RATE: 14519047.25 pps (2x 7259523.625 pps) FINAL_BANDWIDTH: 9.756799752 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘30/917/1063’, ‘10/913/1009’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc09-1518B-2t2c-ethip4-ip4base-iacldstbase-ndrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/330/360’, ‘20/218/281’] LAT_50%NDR: [‘20/26/199’, ‘20/28/52’] LAT_10%NDR: [‘10/26/91’, ‘20/27/136’] |
| tc10-1518B-2t2c-ethip4-ip4base-iacldstbase-pdrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/68/113’, ‘20/347/405’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc11-9000B-2t2c-ethip4-ip4base-iacldstbase-ndrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘60/110/295’, ‘50/89/242’] LAT_50%NDR: [‘50/66/248’, ‘50/65/195’] LAT_10%NDR: [‘50/27/135’, ‘50/31/86’] |
| tc12-9000B-2t2c-ethip4-ip4base-iacldstbase-pdrdisc | [Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘50/291/348’, ‘50/87/168’] LOSS_ACCEPTANCE: 0.5 percentage |
7.1.2.3. 10ge2p1x520-ethip4-ip4base-ipolicemarkbase-ndrpdrdisc¶
RFC2544: Pkt throughput IPv4 policer test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries and policer with 2R3C color-aware configuration. Policer is applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544, RFC2698.
| Name | Documentation | Status |
|---|---|---|
| tc01-64B-1t1c-ethip4-ip4base-ipolicemarkbase-ndrdisc | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 8052380.75 pps (2x 4026190.375 pps) FINAL_BANDWIDTH: 5.411199864 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/1691/1889’, ‘10/1693/1817’] LAT_50%NDR: [‘10/18/58’, ‘20/49/75’] LAT_10%NDR: [‘10/19/151’, ‘10/24/133’] |
| tc02-64B-1t1c-ethip4-ip4base-ipolicemarkbase-pdrdisc | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. |
FINAL_RATE: 8052380.75 pps (2x 4026190.375 pps) FINAL_BANDWIDTH: 5.411199864 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/1681/1858’, ‘20/1687/1827’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc03-1518B-1t1c-ethip4-ip4base-ipolicemarkbase-ndrdisc | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/306/327’, ‘20/407/446’] LAT_50%NDR: [‘20/30/216’, ‘20/30/217’] LAT_10%NDR: [‘20/26/68’, ‘20/24/42’] |
| tc04-1518B-1t1c-ethip4-ip4base-ipolicemarkbase-pdrdisc | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/365/388’, ‘20/371/423’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc05-9000B-1t1c-ethip4-ip4base-ipolicemarkbase-ndrdisc | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘60/318/351’, ‘60/295/364’] LAT_50%NDR: [‘50/66/216’, ‘50/65/219’] LAT_10%NDR: [‘50/61/119’, ‘50/59/90’] |
| tc06-9000B-1t1c-ethip4-ip4base-ipolicemarkbase-pdrdisc | [Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘60/262/325’, ‘50/329/391’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc07-64B-2t2c-ethip4-ip4base-ipolicemarkbase-ndrdisc | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 14057142.5 pps (2x 7028571.25 pps) FINAL_BANDWIDTH: 9.44639976 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/953/1028’, ‘30/945/1095’] LAT_50%NDR: [‘10/27/52’, ‘10/25/92’] LAT_10%NDR: [‘10/24/66’, ‘10/20/168’] |
| tc08-64B-2t2c-ethip4-ip4base-ipolicemarkbase-pdrdisc | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. |
FINAL_RATE: 14057142.5 pps (2x 7028571.25 pps) FINAL_BANDWIDTH: 9.44639976 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/952/1037’, ‘20/944/1099’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc09-1518B-2t2c-ethip4-ip4base-ipolicemarkbase-ndrdisc | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/75/167’, ‘20/186/400’] LAT_50%NDR: [‘20/26/110’, ‘20/27/203’] LAT_10%NDR: [‘20/26/186’, ‘20/27/45’] |
| tc10-1518B-2t2c-ethip4-ip4base-ipolicemarkbase-pdrdisc | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/197/228’, ‘10/384/440’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc11-9000B-2t2c-ethip4-ip4base-ipolicemarkbase-ndrdisc | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘50/205/280’, ‘50/224/275’] LAT_50%NDR: [‘50/64/132’, ‘50/65/235’] LAT_10%NDR: [‘50/61/153’, ‘50/62/93’] |
| tc12-9000B-2t2c-ethip4-ip4base-ipolicemarkbase-pdrdisc | [Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘60/186/213’, ‘50/213/287’] LOSS_ACCEPTANCE: 0.5 percentage |
7.1.2.4. 10ge2p1x520-ethip4-ip4base-ndrpdrdisc¶
RFC2544: Pkt throughput IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
| Name | Documentation | Status |
|---|---|---|
| tc01-64B-1t1c-ethip4-ip4base-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 10592856.875 pps (2x 5296428.4375 pps) FINAL_BANDWIDTH: 7.11839982 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/141/328’, ‘10/136/279’] LAT_50%NDR: [‘10/24/110’, ‘10/24/88’] LAT_10%NDR: [‘10/21/44’, ‘10/19/30’] |
| tc02-64B-1t1c-ethip4-ip4base-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. |
FINAL_RATE: 10592856.875 pps (2x 5296428.4375 pps) FINAL_BANDWIDTH: 7.11839982 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘10/130/267’, ‘10/131/294’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc03-1518B-1t1c-ethip4-ip4base-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/289/307’, ‘20/296/331’] LAT_50%NDR: [‘20/28/127’, ‘20/30/144’] LAT_10%NDR: [‘10/13/73’, ‘10/13/69’] |
| tc04-1518B-1t1c-ethip4-ip4base-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/135/295’, ‘20/142/316’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc05-9000B-1t1c-ethip4-ip4base-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘60/283/342’, ‘50/276/330’] LAT_50%NDR: [‘50/64/188’, ‘50/65/186’] LAT_10%NDR: [‘50/62/94’, ‘50/63/95’] |
| tc06-9000B-1t1c-ethip4-ip4base-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘60/301/392’, ‘50/279/334’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc07-64B-2t2c-ethip4-ip4base-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 22140475.625 pps (2x 11070237.8125 pps) FINAL_BANDWIDTH: 14.87839962 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/82/222’, ‘10/83/167’] LAT_50%NDR: [‘10/21/73’, ‘10/23/44’] LAT_10%NDR: [‘10/20/46’, ‘10/20/38’] |
| tc08-64B-2t2c-ethip4-ip4base-pdrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. |
FINAL_RATE: 22371428.0 pps (2x 11185714.0 pps) FINAL_BANDWIDTH: 15.033599616 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘10/1182/1631’, ‘20/638/1078’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc09-1518B-2t2c-ethip4-ip4base-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/246/298’, ‘20/86/115’] LAT_50%NDR: [‘20/28/194’, ‘20/26/134’] LAT_10%NDR: [‘10/26/85’, ‘10/24/36’] |
| tc10-1518B-2t2c-ethip4-ip4base-pdrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/198/244’, ‘20/37/70’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc11-9000B-2t2c-ethip4-ip4base-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘50/107/252’, ‘50/155/376’] LAT_50%NDR: [‘50/66/202’, ‘50/66/228’] LAT_10%NDR: [‘50/31/121’, ‘50/31/91’] |
| tc12-9000B-2t2c-ethip4-ip4base-pdrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘60/146/334’, ‘50/102/269’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc19-IMIX-1t1c-ethip4-ip4base-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) |
FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps) FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] |
| tc20-IMIX-1t1c-ethip4-ip4base-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B) |
FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps) FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LOSS_ACCEPTANCE: 0.5 percentage |
7.1.2.5. 10ge2p1x520-ethip4-ip4base-snat-ndrpdrdisc¶
SNAT performance test cases High level description - NDR and PDR tests - 3-node topology, TG-DUT1-DUT2-TG, SNAT is enabled between DUTs. - Cores / threads: 1t1c and 2t2c - Framesize: 64B, 1518B, IMIX - Packet: ETH / IP(src, dst) / UDP(src_port, dst_port) / payload Low level description
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, one flow per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
| Name | Documentation | Status |
|---|---|---|
| tc01-64B-1t1c-ethip4-ip4base-snat-1u-1p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1 user and 1 port (session) per user. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 7821428.375 pps (2x 3910714.1875 pps) FINAL_BANDWIDTH: 5.255999868 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/48/671’, ‘10/46/663’] LAT_50%NDR: [‘10/27/171’, ‘10/32/209’] LAT_10%NDR: [‘10/20/162’, ‘10/19/253’] |
| tc02-64B-1t1c-ethip4-ip4base-snat-1u-1p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1 user and 1 port (session) per user. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 7821428.375 pps (2x 3910714.1875 pps) FINAL_BANDWIDTH: 5.255999868 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘10/108/1981’, ‘10/103/1983’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc03-1518B-1t1c-ethip4-ip4base-snat-1u-1p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1 user and 1 port (session) per user. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/336/358’, ‘20/428/446’] LAT_50%NDR: [‘20/29/285’, ‘20/30/283’] LAT_10%NDR: [‘10/26/196’, ‘20/27/159’] |
| tc04-1518B-1t1c-ethip4-ip4base-snat-1u-1p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1 user and 1 port (session) per user. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/390/406’, ‘20/403/433’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc05-IMIX-1t1c-ethip4-ip4base-snat-1u-1p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1 user and 1 port (session) per user. [Ver] Find NDR for IMIX frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps) FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] |
| tc06-IMIX-1t1c-ethip4-ip4base-snat-1u-1p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1 user and 1 port (session) per user. [Ver] Find PDR for IMIX frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps) FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LOSS_ACCEPTANCE: 0.5 percentage |
7.1.2.6. 10ge2p1x520-ethip4-ip4scale-snat-ndrpdrdisc¶
SNAT performance test cases High level description - NDR and PDR tests - 3-node topology, TG-DUT1-DUT2-TG, SNAT is enabled between DUTs. - Cores / threads: 1t1c and 2t2c - Framesize: 64B, 1518B, IMIX - Packet: ETH / IP(src, dst) / UDP(src_port, dst_port) / payload - scale: src: 1 user, 10 users, 100 users, ..., 4000 up to the memory limit; 15 ports per user Low level description
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4-UDP for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 and IPv4/20 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, one flow per flow-group) with all packets containing Ethernet header, IPv4 header with UDP header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
| Name | Documentation | Status |
|---|---|---|
| tc01-64B-1t1c-ethip4-ip4base-snat-1u-15p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1 user and 15 ports (sessions) per user. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 7128571.25 pps (2x 3564285.625 pps) FINAL_BANDWIDTH: 4.79039988 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/159/1907’, ‘10/147/1909’] LAT_50%NDR: [‘10/25/209’, ‘10/27/234’] LAT_10%NDR: [‘10/21/199’, ‘10/20/174’] |
| tc02-64B-1t1c-ethip4-ip4base-snat-1u-15p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1 user and 15 ports (sessions) per user. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 7359523.625 pps (2x 3679761.8125 pps) FINAL_BANDWIDTH: 4.945599876 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘10/162/1886’, ‘10/153/1883’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc03-64B-1t1c-ethip4-ip4base-snat-10u-15p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 10 users and 15 ports (sessions) per user. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 7128571.25 pps (2x 3564285.625 pps) FINAL_BANDWIDTH: 4.79039988 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/1815/1928’, ‘10/1803/1918’] LAT_50%NDR: [‘10/29/179’, ‘10/31/228’] LAT_10%NDR: [‘10/20/48’, ‘10/20/65’] |
| tc04-64B-1t1c-ethip4-ip4base-snat-10u-15p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 10 users and 15 ports (sessions) per user. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 7359523.625 pps (2x 3679761.8125 pps) FINAL_BANDWIDTH: 4.945599876 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘10/1682/1829’, ‘10/1675/1823’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc05-64B-1t1c-ethip4-ip4base-snat-100u-15p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 100 users and 15 ports (sessions) per user. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6897618.875 pps (2x 3448809.4375 pps) FINAL_BANDWIDTH: 4.635199884 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/93/386’, ‘10/91/398’] LAT_50%NDR: [‘10/25/59’, ‘10/27/66’] LAT_10%NDR: [‘10/23/124’, ‘10/22/102’] |
| tc06-64B-1t1c-ethip4-ip4base-snat-100u-15p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 100 users and 15 ports (sessions) per user. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 7128571.25 pps (2x 3564285.625 pps) FINAL_BANDWIDTH: 4.79039988 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘10/1851/1966’, ‘10/1838/1961’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc07-64B-1t1c-ethip4-ip4base-snat-1000u-15p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1000 users and 15 ports (sessions) per user. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6897618.875 pps (2x 3448809.4375 pps) FINAL_BANDWIDTH: 4.635199884 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/131/983’, ‘20/127/961’] LAT_50%NDR: [‘10/27/198’, ‘10/29/159’] LAT_10%NDR: [‘10/22/126’, ‘10/21/107’] |
| tc08-64B-1t1c-ethip4-ip4base-snat-1000u-15p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1000 users and 15 ports (sessions) per user. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6897618.875 pps (2x 3448809.4375 pps) FINAL_BANDWIDTH: 4.635199884 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘10/137/1113’, ‘10/127/1108’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc09-64B-1t1c-ethip4-ip4base-snat-2000u-15p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 2000 users and 15 ports (sessions) per user. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6897618.875 pps (2x 3448809.4375 pps) FINAL_BANDWIDTH: 4.635199884 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/147/1558’, ‘20/151/1579’] LAT_50%NDR: [‘10/29/79’, ‘10/33/88’] LAT_10%NDR: [‘10/20/77’, ‘10/22/86’] |
| tc10-64B-1t1c-ethip4-ip4base-snat-2000u-15p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 2000 users and 15 ports (sessions) per user. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6897618.875 pps (2x 3448809.4375 pps) FINAL_BANDWIDTH: 4.635199884 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘10/149/1248’, ‘10/69/1235’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc11-64B-1t1c-ethip4-ip4base-snat-4000u-15p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 4000 users and 15 ports (sessions) per user. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6666666.5 pps (2x 3333333.25 pps) FINAL_BANDWIDTH: 4.479999888 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/245/2082’, ‘20/236/2068’] LAT_50%NDR: [‘10/26/441’, ‘10/26/450’] LAT_10%NDR: [‘10/20/42’, ‘10/22/71’] |
| tc12-64B-1t1c-ethip4-ip4base-snat-4000u-15p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 4000 users and 15 ports (sessions) per user. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6897618.875 pps (2x 3448809.4375 pps) FINAL_BANDWIDTH: 4.635199884 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘10/160/1892’, ‘10/153/1853’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc13-1518B-1t1c-ethip4-ip4base-snat-1u-15p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1 user and 15 ports (sessions) per user. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/434/454’, ‘20/494/542’] LAT_50%NDR: [‘20/15/217’, ‘20/14/211’] LAT_10%NDR: [‘20/24/226’, ‘10/27/201’] |
| tc14-1518B-1t1c-ethip4-ip4base-snat-1u-15p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1 user and 15 ports (sessions) per user. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/149/315’, ‘20/408/428’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc15-1518B-1t1c-ethip4-ip4base-snat-10u-15p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 10 users and 15 ports (sessions) per user. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/379/396’, ‘20/438/461’] LAT_50%NDR: [‘20/27/188’, ‘10/29/222’] LAT_10%NDR: [‘20/27/154’, ‘10/27/205’] |
| tc16-1518B-1t1c-ethip4-ip4base-snat-10u-15p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 10 users and 15 ports (sessions) per user. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/363/380’, ‘20/427/481’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc17-1518B-1t1c-ethip4-ip4base-snat-100u-15p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 100 users and 15 ports (sessions) per user. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/338/357’, ‘20/397/426’] LAT_50%NDR: [‘20/29/191’, ‘10/28/206’] LAT_10%NDR: [‘20/27/161’, ‘20/27/121’] |
| tc18-1518B-1t1c-ethip4-ip4base-snat-100u-15p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 100 users and 15 ports (sessions) per user. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/327/346’, ‘20/403/422’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc19-1518B-1t1c-ethip4-ip4base-snat-1000u-15p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1000 users and 15 ports (sessions) per user. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 100kpps. |
Search FAILED |
| tc20-1518B-1t1c-ethip4-ip4base-snat-1000u-15p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1000 users and 15 ports (sessions) per user. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/353/372’, ‘20/432/453’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc21-IMIX-1t1c-ethip4-ip4base-snat-1u-15p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1 user and 15 ports (sessions) per user. [Ver] Find NDR for IMIX frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6484738.5 pps (2x 3242369.25 pps) FINAL_BANDWIDTH: 19.3936911011 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] |
| tc22-IMIX-1t1c-ethip4-ip4base-snat-1u-15p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1 user and 15 ports (sessions) per user. [Ver] Find PDR for IMIX frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps) FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc23-IMIX-1t1c-ethip4-ip4base-snat-10u-15p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 10 users and 15 ports (sessions) per user. [Ver] Find NDR for IMIX frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps) FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] |
| tc24-IMIX-1t1c-ethip4-ip4base-snat-10u-15p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 10 users and 15 ports (sessions) per user. [Ver] Find PDR for IMIX frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps) FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc25-IMIX-1t1c-ethip4-ip4base-snat-100u-15p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 100 users and 15 ports (sessions) per user. [Ver] Find NDR for IMIX frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6484738.5 pps (2x 3242369.25 pps) FINAL_BANDWIDTH: 19.3936911011 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] |
| tc26-IMIX-1t1c-ethip4-ip4base-snat-100u-15p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 100 users and 15 ports (sessions) per user. [Ver] Find PDR for IMIX frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps) FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc27-IMIX-1t1c-ethip4-ip4base-snat-1000u-15p-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1000 users and 15 ports (sessions) per user. [Ver] Find NDR for IMIX frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6282005.0 pps (2x 3141002.5 pps) FINAL_BANDWIDTH: 18.7873827858 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] |
| tc28-IMIX-1t1c-ethip4-ip4base-snat-1000u-15p-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. SNAT is configured between DUTs - 1000 users and 15 ports (sessions) per user. [Ver] Find PDR for IMIX frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 6484738.5 pps (2x 3242369.25 pps) FINAL_BANDWIDTH: 19.3936911011 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LOSS_ACCEPTANCE: 0.5 percentage |
7.1.2.7. 10ge2p1x520-ethip4-ip4scale200k-ndrpdrdisc¶
RFC2544: Pkt throughput IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
- [Ref] Applicable standard specifications: RFC2544.
| Name | Documentation | Status |
|---|---|---|
| tc01-64B-1t1c-ethip4-ip4scale200k-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 9669047.375 pps (2x 4834523.6875 pps) FINAL_BANDWIDTH: 6.497599836 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/124/280’, ‘10/123/257’] LAT_50%NDR: [‘10/27/88’, ‘10/26/67’] LAT_10%NDR: [‘10/9/296’, ‘10/9/265’] |
| tc02-64B-1t1c-ethip4-ip4scale200k-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. |
FINAL_RATE: 9669047.375 pps (2x 4834523.6875 pps) FINAL_BANDWIDTH: 6.497599836 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/116/268’, ‘10/114/262’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc03-1518B-1t1c-ethip4-ip4scale200k-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. |
Search FAILED |
| tc04-1518B-1t1c-ethip4-ip4scale200k-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/234/462’, ‘20/182/296’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc05-9000B-1t1c-ethip4-ip4scale200k-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘50/291/374’, ‘50/269/324’] LAT_50%NDR: [‘50/65/202’, ‘50/65/196’] LAT_10%NDR: [‘50/55/99’, ‘50/62/118’] |
| tc06-9000B-1t1c-ethip4-ip4scale200k-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘50/297/529’, ‘60/302/499’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc07-64B-2t2c-ethip4-ip4scale200k-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 20292856.625 pps (2x 10146428.3125 pps) FINAL_BANDWIDTH: 13.636799652 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/72/248’, ‘10/43/235’] LAT_50%NDR: [‘10/23/87’, ‘10/22/109’] LAT_10%NDR: [‘10/18/129’, ‘10/26/70’] |
| tc08-64B-2t2c-ethip4-ip4scale200k-pdrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. |
FINAL_RATE: 20292856.625 pps (2x 10146428.3125 pps) FINAL_BANDWIDTH: 13.636799652 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/80/177’, ‘10/71/95’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc09-1518B-2t2c-ethip4-ip4scale200k-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. |
Search FAILED |
| tc10-1518B-2t2c-ethip4-ip4scale200k-pdrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/145/263’, ‘20/98/210’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc11-9000B-2t2c-ethip4-ip4scale200k-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘60/182/217’, ‘50/209/283’] LAT_50%NDR: [‘50/66/480’, ‘50/65/481’] LAT_10%NDR: [‘50/61/212’, ‘50/62/186’] |
| tc12-9000B-2t2c-ethip4-ip4scale200k-pdrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘60/181/221’, ‘60/191/282’] LOSS_ACCEPTANCE: 0.5 percentage |
7.1.2.8. 10ge2p1x520-ethip4-ip4scale20k-ndrpdrdisc¶
RFC2544: Pkt throughput IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
- [Ref] Applicable standard specifications: RFC2544.
| Name | Documentation | Status |
|---|---|---|
| tc01-64B-1t1c-ethip4-ip4scale20k-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 9669047.375 pps (2x 4834523.6875 pps) FINAL_BANDWIDTH: 6.497599836 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/165/324’, ‘20/164/316’] LAT_50%NDR: [‘10/32/115’, ‘10/29/60’] LAT_10%NDR: [‘10/19/552’, ‘10/20/520’] |
| tc02-64B-1t1c-ethip4-ip4scale20k-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. |
FINAL_RATE: 9669047.375 pps (2x 4834523.6875 pps) FINAL_BANDWIDTH: 6.497599836 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘10/171/303’, ‘10/164/300’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc03-1518B-1t1c-ethip4-ip4scale20k-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/338/380’, ‘20/298/330’] LAT_50%NDR: [‘20/27/163’, ‘20/29/165’] LAT_10%NDR: [‘20/13/138’, ‘10/13/106’] |
| tc04-1518B-1t1c-ethip4-ip4scale20k-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/259/285’, ‘20/273/318’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc05-9000B-1t1c-ethip4-ip4scale20k-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘60/271/491’, ‘50/278/492’] LAT_50%NDR: [‘50/63/192’, ‘50/66/187’] LAT_10%NDR: [‘50/61/98’, ‘50/62/85’] |
| tc06-9000B-1t1c-ethip4-ip4scale20k-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘50/310/406’, ‘50/254/306’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc07-64B-2t2c-ethip4-ip4scale20k-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 20061904.25 pps (2x 10030952.125 pps) FINAL_BANDWIDTH: 13.481599656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/750/877’, ‘20/80/227’] LAT_50%NDR: [‘10/26/51’, ‘10/25/107’] LAT_10%NDR: [‘10/18/34’, ‘10/23/191’] |
| tc08-64B-2t2c-ethip4-ip4scale20k-pdrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. |
FINAL_RATE: 20292856.625 pps (2x 10146428.3125 pps) FINAL_BANDWIDTH: 13.636799652 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘10/84/102’, ‘10/85/105’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc09-1518B-2t2c-ethip4-ip4scale20k-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/225/262’, ‘20/191/213’] LAT_50%NDR: [‘20/27/138’, ‘10/26/191’] LAT_10%NDR: [‘10/26/183’, ‘20/27/41’] |
| tc10-1518B-2t2c-ethip4-ip4scale20k-pdrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/159/188’, ‘20/199/254’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc11-9000B-2t2c-ethip4-ip4scale20k-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘60/187/260’, ‘50/155/235’] LAT_50%NDR: [‘50/64/229’, ‘50/65/89’] LAT_10%NDR: [‘50/62/116’, ‘50/61/125’] |
| tc12-9000B-2t2c-ethip4-ip4scale20k-pdrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘60/298/366’, ‘50/219/269’] LOSS_ACCEPTANCE: 0.5 percentage |
7.1.2.9. 10ge2p1x520-ethip4-ip4scale2m-ndrpdrdisc¶
RFC2544: Pkt throughput IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
- [Ref] Applicable standard specifications: RFC2544.
| Name | Documentation | Status |
|---|---|---|
| tc01-64B-1t1c-ethip4-ip4scale2m-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 8283333.125 pps (2x 4141666.5625 pps) FINAL_BANDWIDTH: 5.56639986 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/113/290’, ‘10/116/282’] LAT_50%NDR: [‘10/35/536’, ‘10/36/535’] LAT_10%NDR: [‘10/23/221’, ‘10/23/201’] |
| tc02-64B-1t1c-ethip4-ip4scale2m-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. |
FINAL_RATE: 8283333.125 pps (2x 4141666.5625 pps) FINAL_BANDWIDTH: 5.56639986 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘10/137/294’, ‘20/138/294’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc03-1518B-1t1c-ethip4-ip4scale2m-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. |
Search FAILED |
| tc04-1518B-1t1c-ethip4-ip4scale2m-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/108/251’, ‘20/235/431’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc05-9000B-1t1c-ethip4-ip4scale2m-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘60/164/248’, ‘50/286/405’] LAT_50%NDR: [‘50/32/188’, ‘50/32/197’] LAT_10%NDR: [‘50/55/220’, ‘50/62/174’] |
| tc06-9000B-1t1c-ethip4-ip4scale2m-pdrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘60/88/248’, ‘50/87/251’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc07-64B-2t2c-ethip4-ip4scale2m-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps. |
FINAL_RATE: 16828571.0 pps (2x 8414285.5 pps) FINAL_BANDWIDTH: 11.308799712 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/315/844’, ‘10/51/277’] LAT_50%NDR: [‘10/27/184’, ‘10/26/49’] LAT_10%NDR: [‘10/20/150’, ‘10/20/72’] |
| tc08-64B-2t2c-ethip4-ip4scale2m-pdrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%. |
FINAL_RATE: 16828571.0 pps (2x 8414285.5 pps) FINAL_BANDWIDTH: 11.308799712 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/844/1003’, ‘20/841/888’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc09-1518B-2t2c-ethip4-ip4scale2m-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps. |
Search FAILED |
| tc10-1518B-2t2c-ethip4-ip4scale2m-pdrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%. |
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps) FINAL_BANDWIDTH: 19.999979744 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘20/44/68’, ‘20/88/121’] LOSS_ACCEPTANCE: 0.5 percentage |
| tc11-9000B-2t2c-ethip4-ip4scale2m-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘60/248/308’, ‘60/77/144’] LAT_50%NDR: [‘50/65/250’, ‘50/65/81’] LAT_10%NDR: [‘50/62/71’, ‘50/61/77’] |
| tc12-9000B-2t2c-ethip4-ip4scale2m-pdrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%. |
FINAL_RATE: 277160.0 pps (2x 138580.0 pps) FINAL_BANDWIDTH: 19.9998656 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%PDR: [‘60/119/149’, ‘60/128/286’] LOSS_ACCEPTANCE: 0.5 percentage |
7.1.2.10. 40ge2p1xl710-ethip4-ip4base-ndrpdrdisc¶
RFC2544: Pkt throughput IPv4 routing test cases
- [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
- [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
- [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p40GE NIC XL710 by Intel.
- [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
- [Ref] Applicable standard specifications: RFC2544.
| Name | Documentation | Status |
|---|---|---|
| tc01-64B-1t1c-ethip4-ip4base-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 18.75Mpps rate, step 100kpps. |
FINAL_RATE: 10107812.5 pps (2x 5053906.25 pps) FINAL_BANDWIDTH: 6.79245 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/253/311’, ‘10/247/291’] LAT_50%NDR: [‘10/24/69’, ‘10/23/50’] LAT_10%NDR: [‘10/19/38’, ‘10/23/62’] |
| tc03-1518B-1t1c-ethip4-ip4base-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps. |
FINAL_RATE: 3982444.0 pps (2x 1991222.0 pps) FINAL_BANDWIDTH: 48.999990976 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/33/179’, ‘10/33/209’] LAT_50%NDR: [‘10/27/208’, ‘10/27/201’] LAT_10%NDR: [‘10/22/129’, ‘10/21/111’] |
| tc07-64B-2t2c-ethip4-ip4base-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 64 Byte frames using binary search start at 18.75Mpps rate, step 100kpps. |
FINAL_RATE: 13021875.0 pps (2x 6510937.5 pps) FINAL_BANDWIDTH: 8.7507 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘10/24/245’, ‘10/23/207’] LAT_50%NDR: [‘10/20/356’, ‘10/20/340’] LAT_10%NDR: [‘10/19/46’, ‘10/18/78’] |
| tc09-1518B-2t2c-ethip4-ip4base-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port. [Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps. |
FINAL_RATE: 3982444.0 pps (2x 1991222.0 pps) FINAL_BANDWIDTH: 48.999990976 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘20/35/185’, ‘20/34/201’] LAT_50%NDR: [‘10/27/179’, ‘10/27/207’] LAT_10%NDR: [‘10/22/87’, ‘10/22/51’] |
| tc19-IMIX-1t1c-ethip4-ip4base-ndrdisc | [Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 24.5G rate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) |
FINAL_RATE: 10062311.4688 pps (2x 5031155.73438 pps) FINAL_BANDWIDTH: 30.093019231 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] |
| tc20-IMIX-2t2c-ethip4-ip4base-ndrdisc | [Cfg] DUT runs IPv4 routing config with 2 thread, 2 phy core, 1 receive queue per NIC port. [Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 24.5G rate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B) |
FINAL_RATE: 12591109.2812 pps (2x 6295554.64062 pps) FINAL_BANDWIDTH: 37.6558104879 Gbps (untagged) LATENCY usec [min/avg/max] LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’] |