7.1.1. L2 Ethernet Switching

Note

Data sources for reported test results: i) FD.io test executor jobs csit-vpp-perf-1701-all/4 , ii) archived FD.io jobs test result output files.

7.1.1.1. 10ge2p1x520-dot1ad-l2xcbase-ndrpdrdisc

RFC2544: Pkt throughput L2XC with 802.1ad test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 xconnect. 802.1ad tagging is applied on link between DUT1 and DUT2 with inner 4B vlan tag (id=100) and outer 4B vlan tag (id=200).
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-dot1ad-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 9050814.875 pps (2x 4525407.4375 pps)
FINAL_BANDWIDTH: 6.082147596 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/2570/2684’, ‘10/1567/1703’]
LAT_50%NDR: [‘10/30/476’, ‘10/29/455’]
LAT_10%NDR: [‘10/21/81’, ‘10/21/67’]
tc02-64B-1t1c-dot1ad-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 9050814.875 pps (2x 4525407.4375 pps)
FINAL_BANDWIDTH: 6.082147596 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/2563/2685’, ‘10/1575/1686’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1514B-1t1c-dot1ad-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.89622544 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/214/268’, ‘20/69/269’]
LAT_50%NDR: [‘20/29/85’, ‘10/30/87’]
LAT_10%NDR: [‘10/13/69’, ‘10/14/45’]
tc04-1514B-1t1c-dot1ad-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.89622544 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/286/454’, ‘20/182/473’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-dot1ad-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 276916.0 pps (2x 138458.0 pps)
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/748/876’, ‘50/196/836’]
LAT_50%NDR: [‘50/66/228’, ‘50/66/235’]
LAT_10%NDR: [‘50/55/104’, ‘50/62/76’]
tc06-9000B-1t1c-dot1ad-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 276916.0 pps (2x 138458.0 pps)
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/185/316’, ‘50/192/296’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-dot1ad-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 18955298.1875 pps (2x 9477649.09375 pps)
FINAL_BANDWIDTH: 12.737960382 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/54/148’, ‘20/156/210’]
LAT_50%NDR: [‘10/24/515’, ‘10/24/607’]
LAT_10%NDR: [‘10/21/45’, ‘10/19/44’]
tc08-64B-2t2c-dot1ad-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 18955298.1875 pps (2x 9477649.09375 pps)
FINAL_BANDWIDTH: 12.737960382 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/55/201’, ‘10/720/808’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1514B-2t2c-dot1ad-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.89622544 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/168/203’, ‘20/134/396’]
LAT_50%NDR: [‘20/27/164’, ‘10/27/65’]
LAT_10%NDR: [‘10/27/61’, ‘10/26/42’]
tc10-1514B-2t2c-dot1ad-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.89622544 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/242/368’, ‘20/150/207’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-dot1ad-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 276916.0 pps (2x 138458.0 pps)
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/213/233’, ‘50/148/237’]
LAT_50%NDR: [‘50/32/228’, ‘50/33/191’]
LAT_10%NDR: [‘50/61/202’, ‘50/59/75’]
tc12-9000B-2t2c-dot1ad-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 276916.0 pps (2x 138458.0 pps)
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/253/399’, ‘50/173/261’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-dot1ad-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 19376765.5625 pps (2x 9688382.78125 pps)
FINAL_BANDWIDTH: 13.021186458 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/47/87’, ‘10/63/219’]
LAT_50%NDR: [‘10/21/542’, ‘10/23/615’]
LAT_10%NDR: [‘10/19/705’, ‘10/20/777’]
tc14-64B-4t4c-dot1ad-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 19587499.25 pps (2x 9793749.625 pps)
FINAL_BANDWIDTH: 13.162799496 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/544/632’, ‘20/547/627’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1514B-4t4c-dot1ad-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.89622544 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/133/286’, ‘20/36/96’]
LAT_50%NDR: [‘10/25/173’, ‘10/27/54’]
LAT_10%NDR: [‘10/26/143’, ‘10/25/40’]
tc16-1514B-4t4c-dot1ad-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1514 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.89622544 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/115/127’, ‘20/40/95’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-dot1ad-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 276916.0 pps (2x 138458.0 pps)
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/103/609’, ‘60/80/579’]
LAT_50%NDR: [‘50/65/222’, ‘50/65/228’]
LAT_10%NDR: [‘50/61/130’, ‘50/55/183’]
tc18-9000B-4t4c-dot1ad-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 276916.0 pps (2x 138458.0 pps)
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/171/252’, ‘60/75/164’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.1.2. 10ge2p1x520-dot1q-l2xcbase-ndrpdrdisc

RFC2544: Pkt throughput L2XC with 802.1q test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-dot1q-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 9015340.625 pps (2x 4507670.3125 pps)
FINAL_BANDWIDTH: 6.0583089 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/2561/2660’, ‘20/1555/1672’]
LAT_50%NDR: [‘10/28/62’, ‘10/28/66’]
LAT_10%NDR: [‘10/21/128’, ‘10/22/80’]
tc02-64B-1t1c-dot1q-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 9015340.625 pps (2x 4507670.3125 pps)
FINAL_BANDWIDTH: 6.0583089 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/2569/2689’, ‘20/1540/1664’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-dot1q-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/148/359’, ‘20/223/354’]
LAT_50%NDR: [‘20/28/190’, ‘20/29/155’]
LAT_10%NDR: [‘20/13/60’, ‘10/14/44’]
tc04-1518B-1t1c-dot1q-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/145/300’, ‘20/171/204’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-dot1q-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277038.0 pps (2x 138519.0 pps)
FINAL_BANDWIDTH: 19.99106208 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/139/305’, ‘50/191/246’]
LAT_50%NDR: [‘50/32/202’, ‘50/33/168’]
LAT_10%NDR: [‘50/61/87’, ‘50/62/90’]
tc06-9000B-1t1c-dot1q-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277038.0 pps (2x 138519.0 pps)
FINAL_BANDWIDTH: 19.99106208 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/747/878’, ‘50/195/856’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-dot1q-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 18712215.3125 pps (2x 9356107.65625 pps)
FINAL_BANDWIDTH: 12.57460869 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/55/112’, ‘20/723/799’]
LAT_50%NDR: [‘10/25/46’, ‘10/24/47’]
LAT_10%NDR: [‘10/20/44’, ‘10/19/51’]
tc08-64B-2t2c-dot1q-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 18932598.8281 pps (2x 9466299.41406 pps)
FINAL_BANDWIDTH: 12.7227064125 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/52/214’, ‘10/725/878’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-dot1q-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/84/513’, ‘20/133/498’]
LAT_50%NDR: [‘10/27/86’, ‘10/27/181’]
LAT_10%NDR: [‘10/27/98’, ‘10/26/50’]
tc10-1518B-2t2c-dot1q-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/86/221’, ‘20/81/148’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-dot1q-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277038.0 pps (2x 138519.0 pps)
FINAL_BANDWIDTH: 19.99106208 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/108/259’, ‘50/78/227’]
LAT_50%NDR: [‘50/32/224’, ‘50/32/130’]
LAT_10%NDR: [‘50/61/78’, ‘50/61/75’]
tc12-9000B-2t2c-dot1q-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277038.0 pps (2x 138519.0 pps)
FINAL_BANDWIDTH: 19.99106208 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/102/162’, ‘60/169/219’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-dot1q-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 23119885.625 pps (2x 11559942.8125 pps)
FINAL_BANDWIDTH: 15.53656314 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/379/394’, ‘20/380/397’]
LAT_50%NDR: [‘10/21/34’, ‘10/20/38’]
LAT_10%NDR: [‘10/19/50’, ‘10/18/34’]
tc14-64B-4t4c-dot1q-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 23119885.625 pps (2x 11559942.8125 pps)
FINAL_BANDWIDTH: 15.53656314 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/381/539’, ‘20/381/404’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-dot1q-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/169/247’, ‘20/93/136’]
LAT_50%NDR: [‘10/26/68’, ‘10/28/168’]
LAT_10%NDR: [‘10/27/44’, ‘10/26/59’]
tc16-1518B-4t4c-dot1q-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/73/119’, ‘20/33/153’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-dot1q-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277038.0 pps (2x 138519.0 pps)
FINAL_BANDWIDTH: 19.99106208 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/116/154’, ‘50/128/298’]
LAT_50%NDR: [‘50/64/149’, ‘50/64/96’]
LAT_10%NDR: [‘50/60/91’, ‘50/61/188’]
tc18-9000B-4t4c-dot1q-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277038.0 pps (2x 138519.0 pps)
FINAL_BANDWIDTH: 19.99106208 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/152/541’, ‘60/76/514’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.1.3. 10ge2p1x520-eth-l2bdbasemaclrn-ndrpdrdisc

RFC2544: Pkt throughput L2BD test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NI X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 10592856.875 pps (2x 5296428.4375 pps)
FINAL_BANDWIDTH: 7.11839982 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/152/208’, ‘10/149/200’]
LAT_50%NDR: [‘10/26/54’, ‘10/26/56’]
LAT_10%NDR: [‘10/22/56’, ‘10/19/33’]
tc02-64B-1t1c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 10592856.875 pps (2x 5296428.4375 pps)
FINAL_BANDWIDTH: 7.11839982 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/120/159’, ‘30/123/168’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/451/941’, ‘20/473/952’]
LAT_50%NDR: [‘20/28/80’, ‘20/30/101’]
LAT_10%NDR: [‘20/26/89’, ‘10/27/174’]
tc04-1518B-1t1c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/108/245’, ‘20/103/214’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/154/174’, ‘60/152/192’]
LAT_50%NDR: [‘50/62/228’, ‘50/66/232’]
LAT_10%NDR: [‘50/56/172’, ‘50/62/124’]
tc06-9000B-1t1c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/247/282’, ‘60/226/244’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 22371428.0 pps (2x 11185714.0 pps)
FINAL_BANDWIDTH: 15.033599616 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/52/501’, ‘20/78/628’]
LAT_50%NDR: [‘10/23/73’, ‘10/24/85’]
LAT_10%NDR: [‘10/21/50’, ‘10/20/48’]
tc08-64B-2t2c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 22833332.75 pps (2x 11416666.375 pps)
FINAL_BANDWIDTH: 15.343999608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/73/104’, ‘10/1159/1196’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
Search FAILED
tc10-1518B-2t2c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/205/215’, ‘20/157/164’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/311/357’, ‘60/87/105’]
LAT_50%NDR: [‘50/65/117’, ‘50/65/233’]
LAT_10%NDR: [‘50/60/97’, ‘50/61/157’]
tc12-9000B-2t2c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/219/270’, ‘60/90/115’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 23295237.5 pps (2x 11647618.75 pps)
FINAL_BANDWIDTH: 15.6543996 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/491/508’, ‘10/486/500’]
LAT_50%NDR: [‘10/19/34’, ‘10/19/32’]
LAT_10%NDR: [‘10/19/46’, ‘10/19/34’]
tc14-64B-4t4c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 23526189.875 pps (2x 11763094.9375 pps)
FINAL_BANDWIDTH: 15.809599596 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/32/77’, ‘10/31/76’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/160/229’, ‘20/172/195’]
LAT_50%NDR: [‘20/26/62’, ‘10/27/53’]
LAT_10%NDR: [‘20/27/52’, ‘10/27/160’]
tc16-1518B-4t4c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/162/226’, ‘20/134/191’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/229/266’, ‘50/103/122’]
LAT_50%NDR: [‘50/65/150’, ‘50/65/267’]
LAT_10%NDR: [‘50/55/228’, ‘50/62/71’]
tc18-9000B-4t4c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/80/110’, ‘50/174/265’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.1.4. 10ge2p1x520-eth-l2xcbase-ndrpdrdisc

RFC2544: Pkt throughput L2XC test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 12671428.25 pps (2x 6335714.125 pps)
FINAL_BANDWIDTH: 8.515199784 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/1060/1162’, ‘10/1065/1168’]
LAT_50%NDR: [‘10/23/843’, ‘10/23/868’]
LAT_10%NDR: [‘10/19/32’, ‘10/19/41’]
tc02-64B-1t1c-eth-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 12671428.25 pps (2x 6335714.125 pps)
FINAL_BANDWIDTH: 8.515199784 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/1060/1160’, ‘20/1074/1163’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/417/447’, ‘20/418/430’]
LAT_50%NDR: [‘20/28/162’, ‘10/29/211’]
LAT_10%NDR: [‘10/27/64’, ‘10/26/59’]
tc04-1518B-1t1c-eth-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/374/441’, ‘20/286/294’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/397/880’, ‘50/414/853’]
LAT_50%NDR: [‘50/61/84’, ‘50/66/86’]
LAT_10%NDR: [‘50/61/84’, ‘50/56/115’]
tc06-9000B-1t1c-eth-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/269/335’, ‘50/401/434’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 23064285.125 pps (2x 11532142.5625 pps)
FINAL_BANDWIDTH: 15.499199604 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/30/107’, ‘10/32/187’]
LAT_50%NDR: [‘10/20/71’, ‘10/20/35’]
LAT_10%NDR: [‘10/19/541’, ‘10/19/495’]
tc08-64B-2t2c-eth-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 23295237.5 pps (2x 11647618.75 pps)
FINAL_BANDWIDTH: 15.6543996 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/953/968’, ‘20/495/556’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/289/327’, ‘20/231/246’]
LAT_50%NDR: [‘10/26/179’, ‘10/27/39’]
LAT_10%NDR: [‘10/27/102’, ‘10/27/97’]
tc10-1518B-2t2c-eth-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/90/114’, ‘20/335/345’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/126/275’, ‘50/189/413’]
LAT_50%NDR: [‘50/64/207’, ‘50/65/95’]
LAT_10%NDR: [‘50/59/90’, ‘50/62/76’]
tc12-9000B-2t2c-eth-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/142/263’, ‘50/312/336’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 23295237.5 pps (2x 11647618.75 pps)
FINAL_BANDWIDTH: 15.6543996 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/943/959’, ‘10/484/664’]
LAT_50%NDR: [‘10/17/541’, ‘10/18/514’]
LAT_10%NDR: [‘10/19/43’, ‘10/18/34’]
tc14-64B-4t4c-eth-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 23295237.5 pps (2x 11647618.75 pps)
FINAL_BANDWIDTH: 15.6543996 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/945/958’, ‘10/488/514’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/84/115’, ‘20/102/275’]
LAT_50%NDR: [‘10/27/77’, ‘10/27/61’]
LAT_10%NDR: [‘10/27/57’, ‘10/24/41’]
tc16-1518B-4t4c-eth-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/184/310’, ‘20/181/242’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/237/270’, ‘50/111/143’]
LAT_50%NDR: [‘50/65/541’, ‘50/65/496’]
LAT_10%NDR: [‘50/61/82’, ‘50/61/87’]
tc18-9000B-4t4c-eth-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/225/256’, ‘60/103/117’]
LOSS_ACCEPTANCE: 0.5 percentage
tc19-IMIX-1t1c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps)
FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc20-IMIX-1t1c-eth-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps)
FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.1.5. 10ge2p1x710-eth-l2bdbasemaclrn-ndrpdrdisc

RFC2544: Pkt throughput L2BD test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 9899999.75 pps (2x 4949999.875 pps)
FINAL_BANDWIDTH: 6.652799832 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/156/254’, ‘20/166/300’]
LAT_50%NDR: [‘10/13/54’, ‘10/13/67’]
LAT_10%NDR: [‘10/20/46’, ‘10/23/60’]
tc02-64B-1t1c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 10130952.125 pps (2x 5065476.0625 pps)
FINAL_BANDWIDTH: 6.807999828 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/182/310’, ‘10/185/357’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/110/203’, ‘20/87/155’]
LAT_50%NDR: [‘10/25/72’, ‘10/25/73’]
LAT_10%NDR: [‘10/25/54’, ‘10/25/33’]
tc04-1518B-1t1c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/330/437’, ‘20/273/330’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘40/143/281’, ‘50/162/282’]
LAT_50%NDR: [‘40/53/107’, ‘40/54/107’]
LAT_10%NDR: [‘40/51/74’, ‘40/51/72’]
tc06-9000B-1t1c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/131/262’, ‘40/241/348’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 12902380.625 pps (2x 6451190.3125 pps)
FINAL_BANDWIDTH: 8.67039978 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/24/84’, ‘10/25/83’]
LAT_50%NDR: [‘10/24/45’, ‘10/23/47’]
LAT_10%NDR: [‘10/20/30’, ‘10/20/100’]
tc08-64B-2t2c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 21678570.875 pps (2x 10839285.4375 pps)
FINAL_BANDWIDTH: 14.567999628 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/59/86’, ‘10/214/232’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/149/243’, ‘10/124/221’]
LAT_50%NDR: [‘10/24/120’, ‘10/25/52’]
LAT_10%NDR: [‘10/25/58’, ‘10/25/36’]
tc10-1518B-2t2c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/36/82’, ‘10/220/270’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘40/73/208’, ‘40/75/118’]
LAT_50%NDR: [‘40/53/78’, ‘40/53/81’]
LAT_10%NDR: [‘40/47/77’, ‘40/51/59’]
tc12-9000B-2t2c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/155/243’, ‘40/91/215’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 22140475.625 pps (2x 11070237.8125 pps)
FINAL_BANDWIDTH: 14.87839962 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/20/41’, ‘10/21/46’]
LAT_50%NDR: [‘10/20/164’, ‘10/20/31’]
LAT_10%NDR: [‘10/20/37’, ‘10/20/70’]
tc14-64B-4t4c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 29761904.0 pps (2x 14880952.0 pps)
FINAL_BANDWIDTH: 19.999999488 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/82/267’, ‘10/36/97’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/73/196’, ‘10/41/93’]
LAT_50%NDR: [‘10/23/54’, ‘10/24/64’]
LAT_10%NDR: [‘10/25/113’, ‘10/24/31’]
tc16-1518B-4t4c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/51/102’, ‘10/74/192’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/706/1060’, ‘40/741/1038’]
LAT_50%NDR: [‘40/52/75’, ‘40/54/136’]
LAT_10%NDR: [‘40/50/81’, ‘40/48/64’]
tc18-9000B-4t4c-eth-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘40/61/103’, ‘40/97/241’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.1.6. 40ge2p1xl710-eth-l2bdbasemaclrn-ndrpdrdisc

RFC2544: Pkt throughput L2BD test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. DUT1 and DUT2 tested with 2p40GE NIC XL710-DA2 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 18.75Mpps rate, step 100kpps.
FINAL_RATE: 9233593.75 pps (2x 4616796.875 pps)
FINAL_BANDWIDTH: 6.204975 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/39/79’, ‘10/41/76’]
LAT_50%NDR: [‘10/27/175’, ‘10/25/176’]
LAT_10%NDR: [‘10/20/47’, ‘10/21/44’]
tc03-1518B-1t1c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps.
FINAL_RATE: 3982444.0 pps (2x 1991222.0 pps)
FINAL_BANDWIDTH: 48.999990976 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/31/239’, ‘10/32/305’]
LAT_50%NDR: [‘10/29/235’, ‘10/28/225’]
LAT_10%NDR: [‘10/23/59’, ‘10/23/53’]
tc07-64B-2t2c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 18.75Mpps rate, step 100kpps.
FINAL_RATE: 15935937.5 pps (2x 7967968.75 pps)
FINAL_BANDWIDTH: 10.70895 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/28/129’, ‘10/28/196’]
LAT_50%NDR: [‘10/21/41’, ‘10/22/68’]
LAT_10%NDR: [‘10/20/72’, ‘10/20/43’]
tc09-1518B-2t2c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 24.5G rate, step 10kpps.
FINAL_RATE: 3982444.0 pps (2x 1991222.0 pps)
FINAL_BANDWIDTH: 48.999990976 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/17/180’, ‘10/16/109’]
LAT_50%NDR: [‘10/25/165’, ‘10/24/93’]
LAT_10%NDR: [‘10/22/61’, ‘10/21/74’]
tc13-64B-4t4c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 18.75Mpps rate, step 100kpps.
FINAL_RATE: 26426562.5 pps (2x 13213281.25 pps)
FINAL_BANDWIDTH: 17.75865 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/11/198’, ‘10/11/74’]
LAT_50%NDR: [‘10/18/35’, ‘10/18/31’]
LAT_10%NDR: [‘10/19/37’, ‘10/19/35’]
tc15-1518B-4t4c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps.
FINAL_RATE: 3889574.21876 pps (2x 1944787.10938 pps)
FINAL_BANDWIDTH: 47.8573211876 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/31/182’, ‘10/31/186’]
LAT_50%NDR: [‘10/28/54’, ‘10/26/52’]
LAT_10%NDR: [‘10/23/53’, ‘10/22/50’]
tc19-IMIX-1t1c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frames using binary search start at 24.5G rate, step 100kpps.
FINAL_RATE: 9050792.34376 pps (2x 4525396.17188 pps)
FINAL_BANDWIDTH: 27.0679027281 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc20-IMIX-2t2c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frames using binary search start at 24.5G rate, step 100kpps.
FINAL_RATE: 16131426.2188 pps (2x 8065713.10938 pps)
FINAL_BANDWIDTH: 48.2437182482 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc21-IMIX-4t4c-eth-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD switching config with with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for IMIX_v4_1 frames using binary search start at 24.5G rate, step 100kpps.
FINAL_RATE: 16384306.0 pps (2x 8192153.0 pps)
FINAL_BANDWIDTH: 48.9999973738 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]

7.1.1.7. 40ge2p1xl710-eth-l2xcbase-ndrpdrdisc

RFC2544: Pkt throughput L2XC test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. DUT1 and DUT2 tested with 2p40GE NIC XL710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 18.75Mpps rate, step 100kpps.
FINAL_RATE: 12439062.5 pps (2x 6219531.25 pps)
FINAL_BANDWIDTH: 8.35905 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/345/398’, ‘20/247/300’]
LAT_50%NDR: [‘10/22/229’, ‘10/20/159’]
LAT_10%NDR: [‘10/19/39’, ‘10/17/38’]
tc03-1518B-1t1c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps.
FINAL_RATE: 3672878.0625 pps (2x 1836439.03125 pps)
FINAL_BANDWIDTH: 45.191091681 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/35/136’, ‘10/34/209’]
LAT_50%NDR: [‘10/27/81’, ‘10/26/76’]
LAT_10%NDR: [‘10/23/190’, ‘10/21/167’]
tc07-64B-2t2c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 18.75Mpps rate, step 100kpps.
FINAL_RATE: 13896093.75 pps (2x 6948046.875 pps)
FINAL_BANDWIDTH: 9.338175 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/21/63’, ‘10/21/81’]
LAT_50%NDR: [‘10/21/499’, ‘10/20/501’]
LAT_10%NDR: [‘10/20/36’, ‘10/17/32’]
tc09-1518B-2t2c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps.
FINAL_RATE: 3703834.65624 pps (2x 1851917.32812 pps)
FINAL_BANDWIDTH: 45.5719816104 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/30/133’, ‘10/30/62’]
LAT_50%NDR: [‘10/26/61’, ‘10/25/58’]
LAT_10%NDR: [‘10/22/55’, ‘10/22/69’]
tc13-64B-4t4c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 18.75Mpps rate, step 100kpps.
FINAL_RATE: 26717968.75 pps (2x 13358984.375 pps)
FINAL_BANDWIDTH: 17.954475 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/20/40’, ‘10/19/39’]
LAT_50%NDR: [‘10/18/176’, ‘10/17/198’]
LAT_10%NDR: [‘10/19/48’, ‘10/19/35’]
tc15-1518B-4t4c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps.
FINAL_RATE: 3580008.28124 pps (2x 1790004.14062 pps)
FINAL_BANDWIDTH: 44.0484218924 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/34/94’, ‘10/33/83’]
LAT_50%NDR: [‘10/24/57’, ‘10/25/185’]
LAT_10%NDR: [‘10/21/42’, ‘10/22/47’]
tc19-IMIX-1t1c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 24.5G rate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 10820950.8125 pps (2x 5410475.40625 pps)
FINAL_BANDWIDTH: 32.361856608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc20-IMIX-2t2c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 2 thread, 2 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 24.5G rate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 12085349.7188 pps (2x 6042674.85938 pps)
FINAL_BANDWIDTH: 36.1432522367 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc21-IMIX-4t4c-eth-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 thread, 4 phy core, 2 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 24.5G rate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 16384306.0 pps (2x 8192153.0 pps)
FINAL_BANDWIDTH: 48.9999973738 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]

7.1.2. IPv4 Routed-Forwarding

Note

Data sources for reported test results: i) FD.io test executor jobs csit-vpp-perf-1701-all/4 , ii) archived FD.io jobs test result output files.

7.1.2.1. 10ge2p1x520-ethip4-ip4base-copwhtlistbase-ndrpdrdisc

RFC2544: Pkt throughput IPv4 whitelist test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 COP security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-ethip4-ip4base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 8283333.125 pps (2x 4141666.5625 pps)
FINAL_BANDWIDTH: 5.56639986 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/108/219’, ‘20/118/241’]
LAT_50%NDR: [‘10/35/649’, ‘10/33/602’]
LAT_10%NDR: [‘10/20/67’, ‘10/24/110’]
tc02-64B-1t1c-ethip4-ip4base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 8514285.5 pps (2x 4257142.75 pps)
FINAL_BANDWIDTH: 5.721599856 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/1599/1724’, ‘20/3041/3182’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip4-ip4base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/942/970’, ‘20/938/946’]
LAT_50%NDR: [‘20/30/189’, ‘20/31/170’]
LAT_10%NDR: [‘20/26/77’, ‘20/27/94’]
tc04-1518B-1t1c-ethip4-ip4base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/465/501’, ‘20/526/534’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip4-ip4base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/384/412’, ‘50/420/459’]
LAT_50%NDR: [‘50/65/151’, ‘50/65/173’]
LAT_10%NDR: [‘50/62/105’, ‘50/62/119’]
tc06-9000B-1t1c-ethip4-ip4base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/393/470’, ‘50/448/490’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-ethip4-ip4base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 15673809.125 pps (2x 7836904.5625 pps)
FINAL_BANDWIDTH: 10.532799732 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/46/75’, ‘10/186/247’]
LAT_50%NDR: [‘10/32/53’, ‘10/25/67’]
LAT_10%NDR: [‘10/22/57’, ‘10/19/191’]
tc08-64B-2t2c-ethip4-ip4base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 15673809.125 pps (2x 7836904.5625 pps)
FINAL_BANDWIDTH: 10.532799732 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/41/79’, ‘20/863/890’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip4-ip4base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/208/229’, ‘20/150/156’]
LAT_50%NDR: [‘20/27/568’, ‘10/28/643’]
LAT_10%NDR: [‘20/27/78’, ‘10/27/93’]
tc10-1518B-2t2c-ethip4-ip4base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/128/163’, ‘20/202/210’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip4-ip4base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/215/583’, ‘50/257/664’]
LAT_50%NDR: [‘50/65/230’, ‘50/64/109’]
LAT_10%NDR: [‘50/55/97’, ‘50/62/181’]
tc12-9000B-2t2c-ethip4-ip4base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/72/259’, ‘60/141/317’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-ethip4-ip4base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/487/508’, ‘10/935/948’]
LAT_50%NDR: [‘10/18/199’, ‘10/22/47’]
LAT_10%NDR: [‘10/20/53’, ‘10/20/37’]
tc14-64B-4t4c-ethip4-ip4base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/486/502’, ‘20/935/1023’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip4-ip4base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/107/118’, ‘20/193/313’]
LAT_50%NDR: [‘10/13/74’, ‘10/14/63’]
LAT_10%NDR: [‘10/27/58’, ‘10/27/50’]
tc16-1518B-4t4c-ethip4-ip4base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/103/271’, ‘20/83/105’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip4-ip4base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/171/271’, ‘60/108/144’]
LAT_50%NDR: [‘50/63/106’, ‘50/65/148’]
LAT_10%NDR: [‘50/61/91’, ‘50/62/79’]
tc18-9000B-4t4c-ethip4-ip4base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/187/251’, ‘60/208/311’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.2.2. 10ge2p1x520-ethip4-ip4base-iacldstbase-ndrpdrdisc

RFC2544: Pkt throughput IPv4 iAcl whitelist test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing, two static IPv4 /24 routes and IPv4 iAcl security whitelist ingress /24 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-ethip4-ip4base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 7821428.375 pps (2x 3910714.1875 pps)
FINAL_BANDWIDTH: 5.255999868 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/175/291’, ‘20/192/334’]
LAT_50%NDR: [‘10/21/79’, ‘10/31/68’]
LAT_10%NDR: [‘10/9/36’, ‘10/11/66’]
tc02-64B-1t1c-ethip4-ip4base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 7821428.375 pps (2x 3910714.1875 pps)
FINAL_BANDWIDTH: 5.255999868 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/177/313’, ‘10/181/296’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip4-ip4base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/443/505’, ‘20/309/316’]
LAT_50%NDR: [‘20/29/210’, ‘20/30/215’]
LAT_10%NDR: [‘20/27/53’, ‘10/24/57’]
tc04-1518B-1t1c-ethip4-ip4base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/461/484’, ‘20/371/376’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip4-ip4base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/366/403’, ‘60/349/364’]
LAT_50%NDR: [‘50/66/230’, ‘50/66/233’]
LAT_10%NDR: [‘50/62/86’, ‘50/62/79’]
tc06-9000B-1t1c-ethip4-ip4base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/391/427’, ‘50/338/371’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-ethip4-ip4base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 13595237.75 pps (2x 6797618.875 pps)
FINAL_BANDWIDTH: 9.135999768 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/42/181’, ‘20/972/1075’]
LAT_50%NDR: [‘10/27/56’, ‘10/26/58’]
LAT_10%NDR: [‘10/19/40’, ‘10/25/51’]
tc08-64B-2t2c-ethip4-ip4base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 13826190.125 pps (2x 6913095.0625 pps)
FINAL_BANDWIDTH: 9.291199764 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/43/74’, ‘30/971/1025’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip4-ip4base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/207/224’, ‘20/173/180’]
LAT_50%NDR: [‘20/27/126’, ‘10/27/140’]
LAT_10%NDR: [‘10/27/66’, ‘10/26/43’]
tc10-1518B-2t2c-ethip4-ip4base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/212/238’, ‘20/189/196’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip4-ip4base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/184/228’, ‘60/143/185’]
LAT_50%NDR: [‘50/66/176’, ‘50/65/82’]
LAT_10%NDR: [‘50/61/191’, ‘50/55/104’]
tc12-9000B-2t2c-ethip4-ip4base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/211/319’, ‘60/102/139’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-ethip4-ip4base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 20292856.625 pps (2x 10146428.3125 pps)
FINAL_BANDWIDTH: 13.636799652 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/37/688’, ‘10/30/89’]
LAT_50%NDR: [‘10/21/50’, ‘10/21/40’]
LAT_10%NDR: [‘10/18/31’, ‘10/22/48’]
tc14-64B-4t4c-ethip4-ip4base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 23526189.875 pps (2x 11763094.9375 pps)
FINAL_BANDWIDTH: 15.809599596 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/108/404’, ‘10/61/289’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip4-ip4base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/130/144’, ‘20/170/175’]
LAT_50%NDR: [‘20/27/85’, ‘20/27/73’]
LAT_10%NDR: [‘10/27/166’, ‘10/24/41’]
tc16-1518B-4t4c-ethip4-ip4base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/257/353’, ‘20/195/214’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip4-ip4base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/132/176’, ‘50/150/209’]
LAT_50%NDR: [‘50/62/93’, ‘50/65/109’]
LAT_10%NDR: [‘50/60/90’, ‘50/61/161’]
tc18-9000B-4t4c-ethip4-ip4base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv4 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/96/192’, ‘60/170/297’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.2.3. 10ge2p1x520-ethip4-ip4base-ipolicemarkbase-ndrpdrdisc

RFC2544: Pkt throughput IPv4 policer test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries and policer with 2R3C color-aware configuration. Policer is applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544, RFC2698.
Name Documentation Message
tc01-64B-1t1c-ethip4-ip4base-ipolicemarkbase-ndrdisc
[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 7590476.0 pps (2x 3795238.0 pps)
FINAL_BANDWIDTH: 5.100799872 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/3396/3514’, ‘20/1818/1941’]
LAT_50%NDR: [‘10/28/195’, ‘10/35/208’]
LAT_10%NDR: [‘10/20/34’, ‘10/21/47’]
tc02-64B-1t1c-ethip4-ip4base-ipolicemarkbase-pdrdisc
[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 7590476.0 pps (2x 3795238.0 pps)
FINAL_BANDWIDTH: 5.100799872 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/3387/3459’, ‘20/1801/1952’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip4-ip4base-ipolicemarkbase-ndrdisc
[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/285/344’, ‘20/358/364’]
LAT_50%NDR: [‘20/27/231’, ‘10/28/226’]
LAT_10%NDR: [‘20/26/60’, ‘20/26/85’]
tc04-1518B-1t1c-ethip4-ip4base-ipolicemarkbase-pdrdisc
[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/475/497’, ‘20/326/334’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip4-ip4base-ipolicemarkbase-ndrdisc
[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/374/406’, ‘50/440/493’]
LAT_50%NDR: [‘50/63/161’, ‘50/65/196’]
LAT_10%NDR: [‘50/62/94’, ‘50/59/72’]
tc06-9000B-1t1c-ethip4-ip4base-ipolicemarkbase-pdrdisc
[Cfg] DUT runs IPv4 routing and policer config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/383/415’, ‘60/412/459’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-ethip4-ip4base-ipolicemarkbase-ndrdisc
[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 12902380.625 pps (2x 6451190.3125 pps)
FINAL_BANDWIDTH: 8.67039978 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/43/66’, ‘20/60/126’]
LAT_50%NDR: [‘10/28/194’, ‘10/27/58’]
LAT_10%NDR: [‘10/19/116’, ‘10/20/91’]
tc08-64B-2t2c-ethip4-ip4base-ipolicemarkbase-pdrdisc
[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 13364285.375 pps (2x 6682142.6875 pps)
FINAL_BANDWIDTH: 8.980799772 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/45/116’, ‘10/1007/1045’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip4-ip4base-ipolicemarkbase-ndrdisc
[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/264/298’, ‘20/197/205’]
LAT_50%NDR: [‘20/27/76’, ‘20/26/78’]
LAT_10%NDR: [‘10/27/61’, ‘10/27/39’]
tc10-1518B-2t2c-ethip4-ip4base-ipolicemarkbase-pdrdisc
[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/203/228’, ‘20/271/278’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip4-ip4base-ipolicemarkbase-ndrdisc
[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/322/364’, ‘50/194/215’]
LAT_50%NDR: [‘50/66/230’, ‘50/66/205’]
LAT_10%NDR: [‘50/60/132’, ‘50/62/72’]
tc12-9000B-2t2c-ethip4-ip4base-ipolicemarkbase-pdrdisc
[Cfg] DUT runs IPv4 routing and policer config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/98/142’, ‘50/338/358’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-ethip4-ip4base-ipolicemarkbase-ndrdisc
[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 22140475.625 pps (2x 11070237.8125 pps)
FINAL_BANDWIDTH: 14.87839962 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/142/573’, ‘20/51/326’]
LAT_50%NDR: [‘10/22/43’, ‘10/21/45’]
LAT_10%NDR: [‘10/20/58’, ‘10/20/139’]
tc14-64B-4t4c-ethip4-ip4base-ipolicemarkbase-pdrdisc
[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 22833332.75 pps (2x 11416666.375 pps)
FINAL_BANDWIDTH: 15.343999608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘30/516/923’, ‘10/49/222’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip4-ip4base-ipolicemarkbase-ndrdisc
[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/172/236’, ‘20/123/131’]
LAT_50%NDR: [‘20/26/201’, ‘10/28/59’]
LAT_10%NDR: [‘20/27/54’, ‘10/27/42’]
tc16-1518B-4t4c-ethip4-ip4base-ipolicemarkbase-pdrdisc
[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/89/127’, ‘20/169/250’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip4-ip4base-ipolicemarkbase-ndrdisc
[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/146/197’, ‘50/195/217’]
LAT_50%NDR: [‘50/65/157’, ‘50/65/107’]
LAT_10%NDR: [‘50/59/502’, ‘50/62/566’]
tc18-9000B-4t4c-ethip4-ip4base-ipolicemarkbase-pdrdisc
[Cfg] DUT runs IPv4 routing and policer config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/172/213’, ‘60/166/206’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.2.4. 10ge2p1x520-ethip4-ip4base-ndrpdrdisc

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 9669047.375 pps (2x 4834523.6875 pps)
FINAL_BANDWIDTH: 6.497599836 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/76/253’, ‘20/77/278’]
LAT_50%NDR: [‘10/29/104’, ‘10/26/81’]
LAT_10%NDR: [‘10/20/45’, ‘10/20/61’]
tc02-64B-1t1c-ethip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 9669047.375 pps (2x 4834523.6875 pps)
FINAL_BANDWIDTH: 6.497599836 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/82/214’, ‘10/83/223’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/335/376’, ‘20/450/458’]
LAT_50%NDR: [‘20/29/158’, ‘10/29/199’]
LAT_10%NDR: [‘10/27/64’, ‘10/28/83’]
tc04-1518B-1t1c-ethip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/904/952’, ‘20/939/950’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/234/309’, ‘60/376/416’]
LAT_50%NDR: [‘50/65/116’, ‘50/65/116’]
LAT_10%NDR: [‘50/61/76’, ‘50/57/96’]
tc06-9000B-1t1c-ethip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/759/785’, ‘50/840/868’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 20523809.0 pps (2x 10261904.5 pps)
FINAL_BANDWIDTH: 13.791999648 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/51/112’, ‘20/683/750’]
LAT_50%NDR: [‘10/23/68’, ‘10/24/41’]
LAT_10%NDR: [‘10/18/37’, ‘10/20/36’]
tc08-64B-2t2c-ethip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 20523809.0 pps (2x 10261904.5 pps)
FINAL_BANDWIDTH: 13.791999648 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/57/85’, ‘20/678/704’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/242/280’, ‘20/300/308’]
LAT_50%NDR: [‘10/27/72’, ‘10/27/182’]
LAT_10%NDR: [‘10/26/49’, ‘10/27/42’]
tc10-1518B-2t2c-ethip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/114/156’, ‘20/438/453’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/274/303’, ‘50/128/166’]
LAT_50%NDR: [‘50/65/248’, ‘50/64/103’]
LAT_10%NDR: [‘50/61/97’, ‘50/62/79’]
tc12-9000B-2t2c-ethip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/105/124’, ‘60/308/330’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 23526189.875 pps (2x 11763094.9375 pps)
FINAL_BANDWIDTH: 15.809599596 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/27/84’, ‘10/28/83’]
LAT_50%NDR: [‘10/18/30’, ‘10/18/36’]
LAT_10%NDR: [‘10/19/31’, ‘10/19/30’]
tc14-64B-4t4c-ethip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/481/552’, ‘20/692/714’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/100/235’, ‘20/124/224’]
LAT_50%NDR: [‘10/27/52’, ‘10/27/142’]
LAT_10%NDR: [‘10/26/59’, ‘10/27/139’]
tc16-1518B-4t4c-ethip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/156/176’, ‘20/307/327’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/144/195’, ‘50/192/263’]
LAT_50%NDR: [‘50/64/255’, ‘50/65/235’]
LAT_10%NDR: [‘50/62/113’, ‘50/61/112’]
tc18-9000B-4t4c-ethip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/153/291’, ‘60/159/228’]
LOSS_ACCEPTANCE: 0.5 percentage
tc19-IMIX-1t1c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps)
FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc20-IMIX-1t1c-ethip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 100kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 6687472.0 pps (2x 3343736.0 pps)
FINAL_BANDWIDTH: 19.9999994163 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.2.5. 10ge2p1x520-ethip4-ip4scale200k-ndrpdrdisc

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x100k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-ethip4-ip4scale200k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 8976190.25 pps (2x 4488095.125 pps)
FINAL_BANDWIDTH: 6.031999848 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/1511/2818’, ‘30/2808/2895’]
LAT_50%NDR: [‘10/22/50’, ‘10/23/81’]
LAT_10%NDR: [‘10/19/776’, ‘10/20/779’]
tc02-64B-1t1c-ethip4-ip4scale200k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 8976190.25 pps (2x 4488095.125 pps)
FINAL_BANDWIDTH: 6.031999848 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/2841/2920’, ‘30/1547/1647’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip4-ip4scale200k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
Search FAILED
tc04-1518B-1t1c-ethip4-ip4scale200k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/359/479’, ‘20/258/344’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip4-ip4scale200k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/396/509’, ‘50/284/327’]
LAT_50%NDR: [‘50/66/234’, ‘50/66/228’]
LAT_10%NDR: [‘50/61/88’, ‘50/62/89’]
tc06-9000B-1t1c-ethip4-ip4scale200k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/381/408’, ‘50/386/427’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-ethip4-ip4scale200k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 19138094.75 pps (2x 9569047.375 pps)
FINAL_BANDWIDTH: 12.860799672 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/49/151’, ‘10/736/808’]
LAT_50%NDR: [‘10/23/83’, ‘10/24/51’]
LAT_10%NDR: [‘10/19/37’, ‘10/20/47’]
tc08-64B-2t2c-ethip4-ip4scale200k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 19138094.75 pps (2x 9569047.375 pps)
FINAL_BANDWIDTH: 12.860799672 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/51/121’, ‘10/738/769’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip4-ip4scale200k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
Search FAILED
tc10-1518B-2t2c-ethip4-ip4scale200k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/156/208’, ‘20/105/278’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip4-ip4scale200k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/249/294’, ‘60/249/270’]
LAT_50%NDR: [‘50/66/144’, ‘50/65/139’]
LAT_10%NDR: [‘50/59/152’, ‘50/62/90’]
tc12-9000B-2t2c-ethip4-ip4scale200k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/377/450’, ‘50/209/228’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-ethip4-ip4scale200k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/481/580’, ‘10/933/948’]
LAT_50%NDR: [‘10/18/60’, ‘10/18/32’]
LAT_10%NDR: [‘10/18/186’, ‘10/18/38’]
tc14-64B-4t4c-ethip4-ip4scale200k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/480/498’, ‘10/933/949’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip4-ip4scale200k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
Search FAILED
tc16-1518B-4t4c-ethip4-ip4scale200k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/30/82’, ‘20/76/208’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip4-ip4scale200k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/228/269’, ‘50/103/133’]
LAT_50%NDR: [‘50/65/179’, ‘50/64/118’]
LAT_10%NDR: [‘50/61/247’, ‘50/56/97’]
tc18-9000B-4t4c-ethip4-ip4scale200k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/166/202’, ‘50/134/200’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.2.6. 10ge2p1x520-ethip4-ip4scale20k-ndrpdrdisc

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x10k static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-ethip4-ip4scale20k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 9207142.625 pps (2x 4603571.3125 pps)
FINAL_BANDWIDTH: 6.187199844 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/193/322’, ‘10/215/297’]
LAT_50%NDR: [‘10/30/227’, ‘10/31/186’]
LAT_10%NDR: [‘10/20/49’, ‘10/21/51’]
tc02-64B-1t1c-ethip4-ip4scale20k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 8976190.25 pps (2x 4488095.125 pps)
FINAL_BANDWIDTH: 6.031999848 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/1576/1808’, ‘30/2863/2932’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip4-ip4scale20k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/455/908’, ‘20/378/767’]
LAT_50%NDR: [‘20/29/254’, ‘10/29/253’]
LAT_10%NDR: [‘20/26/83’, ‘10/28/106’]
tc04-1518B-1t1c-ethip4-ip4scale20k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/330/363’, ‘20/248/260’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip4-ip4scale20k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/352/393’, ‘50/404/442’]
LAT_50%NDR: [‘50/64/187’, ‘50/64/191’]
LAT_10%NDR: [‘50/61/80’, ‘50/54/110’]
tc06-9000B-1t1c-ethip4-ip4scale20k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/326/355’, ‘60/221/254’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-ethip4-ip4scale20k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 19369047.125 pps (2x 9684523.5625 pps)
FINAL_BANDWIDTH: 13.015999668 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/46/201’, ‘20/243/336’]
LAT_50%NDR: [‘10/22/93’, ‘10/23/44’]
LAT_10%NDR: [‘10/19/34’, ‘10/20/41’]
tc08-64B-2t2c-ethip4-ip4scale20k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 19138094.75 pps (2x 9569047.375 pps)
FINAL_BANDWIDTH: 12.860799672 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/57/229’, ‘10/739/873’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip4-ip4scale20k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/243/724’, ‘20/197/620’]
LAT_50%NDR: [‘10/26/198’, ‘10/27/62’]
LAT_10%NDR: [‘10/27/51’, ‘10/27/36’]
tc10-1518B-2t2c-ethip4-ip4scale20k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/339/390’, ‘20/264/270’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip4-ip4scale20k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/125/242’, ‘50/213/228’]
LAT_50%NDR: [‘50/65/92’, ‘50/64/215’]
LAT_10%NDR: [‘50/61/97’, ‘50/61/152’]
tc12-9000B-2t2c-ethip4-ip4scale20k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/101/138’, ‘60/376/411’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-ethip4-ip4scale20k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/481/543’, ‘20/933/947’]
LAT_50%NDR: [‘10/18/33’, ‘10/18/31’]
LAT_10%NDR: [‘10/20/36’, ‘10/19/32’]
tc14-64B-4t4c-ethip4-ip4scale20k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/482/563’, ‘20/931/946’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip4-ip4scale20k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/140/650’, ‘20/166/499’]
LAT_50%NDR: [‘20/27/78’, ‘10/28/184’]
LAT_10%NDR: [‘10/26/47’, ‘10/27/83’]
tc16-1518B-4t4c-ethip4-ip4scale20k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/141/244’, ‘20/169/268’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip4-ip4scale20k-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/157/192’, ‘60/209/231’]
LAT_50%NDR: [‘50/64/186’, ‘50/65/116’]
LAT_10%NDR: [‘50/57/88’, ‘50/61/201’]
tc18-9000B-4t4c-ethip4-ip4scale20k-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/164/265’, ‘50/215/334’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.2.7. 10ge2p1x520-ethip4-ip4scale2m-ndrpdrdisc

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and 2x1M static IPv4 /32 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv4 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-ethip4-ip4scale2m-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 8052380.75 pps (2x 4026190.375 pps)
FINAL_BANDWIDTH: 5.411199864 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/2108/3237’, ‘20/2800/3246’]
LAT_50%NDR: [‘10/34/199’, ‘10/34/269’]
LAT_10%NDR: [‘10/20/155’, ‘10/24/114’]
tc02-64B-1t1c-ethip4-ip4scale2m-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 8052380.75 pps (2x 4026190.375 pps)
FINAL_BANDWIDTH: 5.411199864 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/997/2272’, ‘10/1328/3089’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip4-ip4scale2m-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
Search FAILED
tc04-1518B-1t1c-ethip4-ip4scale2m-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/212/331’, ‘20/296/324’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip4-ip4scale2m-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/94/199’, ‘50/120/161’]
LAT_50%NDR: [‘50/62/84’, ‘50/65/88’]
LAT_10%NDR: [‘50/61/86’, ‘50/57/90’]
tc06-9000B-1t1c-ethip4-ip4scale2m-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/133/216’, ‘50/177/212’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-ethip4-ip4scale2m-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 16366666.25 pps (2x 8183333.125 pps)
FINAL_BANDWIDTH: 10.99839972 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/59/155’, ‘20/850/959’]
LAT_50%NDR: [‘10/31/53’, ‘10/23/47’]
LAT_10%NDR: [‘10/19/154’, ‘10/20/62’]
tc08-64B-2t2c-ethip4-ip4scale2m-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 16135713.875 pps (2x 8067856.9375 pps)
FINAL_BANDWIDTH: 10.843199724 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/51/163’, ‘20/117/425’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip4-ip4scale2m-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
Search FAILED
tc10-1518B-2t2c-ethip4-ip4scale2m-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/74/122’, ‘20/145/251’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip4-ip4scale2m-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/74/107’, ‘50/367/404’]
LAT_50%NDR: [‘50/65/85’, ‘50/66/209’]
LAT_10%NDR: [‘50/61/77’, ‘50/62/226’]
tc12-9000B-2t2c-ethip4-ip4scale2m-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/73/121’, ‘50/260/283’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-ethip4-ip4scale2m-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 23526189.875 pps (2x 11763094.9375 pps)
FINAL_BANDWIDTH: 15.809599596 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/33/144’, ‘10/33/77’]
LAT_50%NDR: [‘10/20/483’, ‘10/20/477’]
LAT_10%NDR: [‘10/20/40’, ‘10/19/38’]
tc14-64B-4t4c-ethip4-ip4scale2m-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 23757142.25 pps (2x 11878571.125 pps)
FINAL_BANDWIDTH: 15.964799592 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/938/1003’, ‘20/938/1039’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip4-ip4scale2m-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
Search FAILED
tc16-1518B-4t4c-ethip4-ip4scale2m-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/33/54’, ‘20/32/84’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip4-ip4scale2m-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
Search FAILED
tc18-9000B-4t4c-ethip4-ip4scale2m-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 245015.0 pps (2x 122507.5 pps)
FINAL_BANDWIDTH: 17.6802824 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/70/149’, ‘50/70/293’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.2.8. 40ge2p1xl710-ethip4-ip4base-ndrpdrdisc

RFC2544: Pkt throughput IPv4 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. DUT1 and DUT2 tested with 2p40GE NIC XL710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 18.75Mpps rate, step 100kpps.
FINAL_RATE: 9525000.0 pps (2x 4762500.0 pps)
FINAL_BANDWIDTH: 6.4008 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/280/386’, ‘10/303/429’]
LAT_50%NDR: [‘10/26/95’, ‘10/27/69’]
LAT_10%NDR: [‘10/21/45’, ‘10/19/33’]
tc03-1518B-1t1c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps.
FINAL_RATE: 3920530.8125 pps (2x 1960265.40625 pps)
FINAL_BANDWIDTH: 48.238211117 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/366/433’, ‘10/195/264’]
LAT_50%NDR: [‘10/28/56’, ‘10/27/55’]
LAT_10%NDR: [‘10/23/58’, ‘10/22/68’]
tc07-64B-2t2c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 18.75Mpps rate, step 100kpps.
FINAL_RATE: 13896093.75 pps (2x 6948046.875 pps)
FINAL_BANDWIDTH: 9.338175 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/31/55’, ‘10/31/60’]
LAT_50%NDR: [‘10/13/554’, ‘10/12/533’]
LAT_10%NDR: [‘10/21/38’, ‘10/19/69’]
tc09-1518B-2t2c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps.
FINAL_RATE: 3920530.8125 pps (2x 1960265.40625 pps)
FINAL_BANDWIDTH: 48.238211117 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/203/214’, ‘10/361/372’]
LAT_50%NDR: [‘10/20/54’, ‘10/22/72’]
LAT_10%NDR: [‘10/22/37’, ‘10/21/35’]
tc13-64B-4t4c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 18.75Mpps rate, step 100kpps.
FINAL_RATE: 25552343.75 pps (2x 12776171.875 pps)
FINAL_BANDWIDTH: 17.171175 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/21/83’, ‘10/21/97’]
LAT_50%NDR: [‘10/9/580’, ‘10/9/550’]
LAT_10%NDR: [‘10/19/34’, ‘10/19/46’]
tc15-1518B-4t4c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps.
FINAL_RATE: 3889574.21876 pps (2x 1944787.10938 pps)
FINAL_BANDWIDTH: 47.8573211876 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/35/49’, ‘10/40/108’]
LAT_50%NDR: [‘10/25/53’, ‘10/26/50’]
LAT_10%NDR: [‘10/23/62’, ‘10/23/44’]
tc19-IMIX-1t1c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 24.5G rate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 9050792.34376 pps (2x 4525396.17188 pps)
FINAL_BANDWIDTH: 27.0679027281 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc20-IMIX-2t2c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 thread, 2 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 24.5G rate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 14361267.75 pps (2x 7180633.875 pps)
FINAL_BANDWIDTH: 42.949764368 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc21-IMIX-4t4c-ethip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 thread, 4 phy core, 2 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 24.5G rate, step 100kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 16384306.0 pps (2x 8192153.0 pps)
FINAL_BANDWIDTH: 48.9999973738 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]

7.1.3. IPv6 Routed-Forwarding

Note

Data sources for reported test results: i) FD.io test executor jobs csit-vpp-perf-1701-all/4 , ii) archived FD.io jobs test result output files.

7.1.3.1. 10ge2p1x520-ethip6-ip6base-copwhtlistbase-ndrpdrdisc

RFC2544: Pkt throughput IPv6 whitelist test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 COP security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-78B-1t1c-ethip6-ip6base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 6527551.0 pps (2x 3263775.5 pps)
FINAL_BANDWIDTH: 5.117599984 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/1732/1963’, ‘10/3148/3255’]
LAT_50%NDR: [‘10/37/175’, ‘10/35/121’]
LAT_10%NDR: [‘10/20/64’, ‘10/24/87’]
tc02-78B-1t1c-ethip6-ip6base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 6527551.0 pps (2x 3263775.5 pps)
FINAL_BANDWIDTH: 5.117599984 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/3151/3336’, ‘10/1701/1879’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip6-ip6base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/453/487’, ‘20/406/413’]
LAT_50%NDR: [‘20/29/266’, ‘20/32/267’]
LAT_10%NDR: [‘20/28/125’, ‘20/28/87’]
tc04-1518B-1t1c-ethip6-ip6base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/350/373’, ‘20/426/435’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip6-ip6base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/245/339’, ‘50/249/279’]
LAT_50%NDR: [‘50/67/244’, ‘50/63/181’]
LAT_10%NDR: [‘50/58/212’, ‘50/62/179’]
tc06-9000B-1t1c-ethip6-ip6base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/359/428’, ‘50/312/345’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-78B-2t2c-ethip6-ip6base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 11273214.25 pps (2x 5636607.125 pps)
FINAL_BANDWIDTH: 8.838199972 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/50/79’, ‘20/937/1007’]
LAT_50%NDR: [‘10/28/64’, ‘10/28/65’]
LAT_10%NDR: [‘10/22/54’, ‘10/20/40’]
tc08-78B-2t2c-ethip6-ip6base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 10482270.375 pps (2x 5241135.1875 pps)
FINAL_BANDWIDTH: 8.218099974 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/46/158’, ‘10/1000/1158’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip6-ip6base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/95/232’, ‘20/137/282’]
LAT_50%NDR: [‘20/28/80’, ‘20/28/70’]
LAT_10%NDR: [‘20/27/96’, ‘20/28/46’]
tc10-1518B-2t2c-ethip6-ip6base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/172/234’, ‘20/236/246’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip6-ip6base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/265/311’, ‘50/102/119’]
LAT_50%NDR: [‘50/63/163’, ‘50/65/112’]
LAT_10%NDR: [‘50/55/183’, ‘50/62/106’]
tc12-9000B-2t2c-ethip6-ip6base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/248/277’, ‘60/196/227’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-78B-4t4c-ethip6-ip6base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 21160012.6876 pps (2x 10580006.3438 pps)
FINAL_BANDWIDTH: 16.5894499471 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/40/147’, ‘10/42/112’]
LAT_50%NDR: [‘10/22/42’, ‘10/23/43’]
LAT_10%NDR: [‘10/21/51’, ‘10/19/38’]
tc14-78B-4t4c-ethip6-ip6base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 21160012.6876 pps (2x 10580006.3438 pps)
FINAL_BANDWIDTH: 16.5894499471 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/38/244’, ‘10/40/109’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip6-ip6base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/178/296’, ‘20/157/239’]
LAT_50%NDR: [‘20/28/152’, ‘20/28/172’]
LAT_10%NDR: [‘20/27/68’, ‘20/27/125’]
tc16-1518B-4t4c-ethip6-ip6base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/107/307’, ‘20/49/106’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip6-ip6base-copwhtlistbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/184/245’, ‘50/182/199’]
LAT_50%NDR: [‘50/63/270’, ‘50/65/120’]
LAT_10%NDR: [‘50/61/97’, ‘50/56/100’]
tc18-9000B-4t4c-ethip6-ip6base-copwhtlistbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/129/174’, ‘60/176/241’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.3.2. 10ge2p1x520-ethip6-ip6base-iacldstbase-ndrpdrdisc

RFC2544: Pkt throughput IPv6 iAcl whitelist test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing, two static IPv6 /64 routes and IPv6 iAcl security whitelist ingress /64 filter entries applied on links TG - DUT1 and DUT2 - TG. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-78B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 6527551.0 pps (2x 3263775.5 pps)
FINAL_BANDWIDTH: 5.117599984 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/3139/3224’, ‘20/1701/1848’]
LAT_50%NDR: [‘10/37/93’, ‘10/36/87’]
LAT_10%NDR: [‘10/20/189’, ‘10/21/166’]
tc02-78B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 6527551.0 pps (2x 3263775.5 pps)
FINAL_BANDWIDTH: 5.117599984 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘30/3138/3227’, ‘50/1701/1776’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/186/279’, ‘20/291/311’]
LAT_50%NDR: [‘20/30/218’, ‘20/31/185’]
LAT_10%NDR: [‘20/13/61’, ‘20/13/51’]
tc04-1518B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/350/362’, ‘20/385/391’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip6-ip6base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/362/406’, ‘50/432/464’]
LAT_50%NDR: [‘50/65/189’, ‘50/67/176’]
LAT_10%NDR: [‘50/61/180’, ‘50/58/238’]
tc06-9000B-1t1c-ethip6-ip6base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/241/261’, ‘50/357/381’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-78B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 11273214.25 pps (2x 5636607.125 pps)
FINAL_BANDWIDTH: 8.838199972 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/912/974’, ‘10/933/1009’]
LAT_50%NDR: [‘10/30/124’, ‘10/29/63’]
LAT_10%NDR: [‘10/22/203’, ‘10/20/43’]
tc08-78B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 11668686.1875 pps (2x 5834343.09375 pps)
FINAL_BANDWIDTH: 9.148249971 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/50/164’, ‘30/916/984’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/150/223’, ‘20/274/282’]
LAT_50%NDR: [‘20/27/116’, ‘20/27/197’]
LAT_10%NDR: [‘20/27/147’, ‘20/27/57’]
tc10-1518B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/97/120’, ‘20/396/405’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip6-ip6base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/107/149’, ‘50/311/349’]
LAT_50%NDR: [‘50/66/170’, ‘50/66/220’]
LAT_10%NDR: [‘50/56/200’, ‘50/62/114’]
tc12-9000B-2t2c-ethip6-ip6base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/330/385’, ‘50/189/242’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-78B-4t4c-ethip6-ip6base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 20369068.8124 pps (2x 10184534.4062 pps)
FINAL_BANDWIDTH: 15.9693499489 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/67/178’, ‘20/49/116’]
LAT_50%NDR: [‘10/24/46’, ‘10/22/71’]
LAT_10%NDR: [‘10/19/49’, ‘10/26/241’]
tc14-78B-4t4c-ethip6-ip6base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 21160012.6876 pps (2x 10580006.3438 pps)
FINAL_BANDWIDTH: 16.5894499471 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/105/528’, ‘20/77/194’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip6-ip6base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/183/240’, ‘20/109/120’]
LAT_50%NDR: [‘20/28/194’, ‘20/28/235’]
LAT_10%NDR: [‘20/27/124’, ‘20/24/40’]
tc16-1518B-4t4c-ethip6-ip6base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/216/239’, ‘20/74/80’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip6-ip6base-iacldstbase-ndrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/241/332’, ‘60/121/170’]
LAT_50%NDR: [‘50/65/248’, ‘50/66/127’]
LAT_10%NDR: [‘50/62/170’, ‘50/62/80’]
tc18-9000B-4t4c-ethip6-ip6base-iacldstbase-pdrdisc
[Cfg] DUT runs IPv6 routing and whitelist filters config with 4 threads, 4 phy cores, 2 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/139/166’, ‘50/197/308’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.3.3. 10ge2p1x520-ethip6-ip6base-ndrpdrdisc

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-78B-1t1c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 7713966.8125 pps (2x 3856983.40625 pps)
FINAL_BANDWIDTH: 6.047749981 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/202/333’, ‘20/217/350’]
LAT_50%NDR: [‘10/22/67’, ‘10/37/105’]
LAT_10%NDR: [‘10/20/34’, ‘10/22/80’]
tc02-78B-1t1c-ethip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 7713966.8125 pps (2x 3856983.40625 pps)
FINAL_BANDWIDTH: 6.047749981 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/1418/1503’, ‘10/1417/1484’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/295/340’, ‘20/111/230’]
LAT_50%NDR: [‘20/28/116’, ‘20/29/192’]
LAT_10%NDR: [‘20/26/98’, ‘20/27/162’]
tc04-1518B-1t1c-ethip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/159/208’, ‘20/218/226’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/784/949’, ‘50/868/1040’]
LAT_50%NDR: [‘50/64/257’, ‘50/63/268’]
LAT_10%NDR: [‘50/61/88’, ‘50/61/74’]
tc06-9000B-1t1c-ethip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/859/944’, ‘60/927/1023’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-78B-2t2c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 15623405.5625 pps (2x 7811702.78125 pps)
FINAL_BANDWIDTH: 12.248749961 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/47/147’, ‘20/177/307’]
LAT_50%NDR: [‘10/29/51’, ‘10/26/61’]
LAT_10%NDR: [‘10/22/51’, ‘10/20/47’]
tc08-78B-2t2c-ethip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 15623405.5625 pps (2x 7811702.78125 pps)
FINAL_BANDWIDTH: 12.248749961 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/48/80’, ‘10/88/114’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/76/101’, ‘20/261/269’]
LAT_50%NDR: [‘20/27/122’, ‘20/27/103’]
LAT_10%NDR: [‘20/27/70’, ‘10/26/46’]
tc10-1518B-2t2c-ethip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/245/261’, ‘20/185/193’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/104/145’, ‘50/206/248’]
LAT_50%NDR: [‘50/66/96’, ‘50/65/143’]
LAT_10%NDR: [‘50/61/90’, ‘50/62/110’]
tc12-9000B-2t2c-ethip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/220/252’, ‘50/162/197’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-78B-4t4c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 21160012.6876 pps (2x 10580006.3438 pps)
FINAL_BANDWIDTH: 16.5894499471 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/29/106’, ‘10/30/117’]
LAT_50%NDR: [‘10/20/49’, ‘10/19/51’]
LAT_10%NDR: [‘10/19/58’, ‘10/19/57’]
tc14-78B-4t4c-ethip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 21555484.625 pps (2x 10777742.3125 pps)
FINAL_BANDWIDTH: 16.899499946 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/404/510’, ‘10/777/840’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/126/143’, ‘20/184/229’]
LAT_50%NDR: [‘20/28/54’, ‘20/28/74’]
LAT_10%NDR: [‘20/26/97’, ‘10/24/192’]
tc16-1518B-4t4c-ethip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/242/342’, ‘20/100/110’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/173/313’, ‘50/128/158’]
LAT_50%NDR: [‘50/64/231’, ‘50/65/115’]
LAT_10%NDR: [‘50/55/90’, ‘50/62/74’]
tc18-9000B-4t4c-ethip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/159/211’, ‘60/174/205’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.3.4. 10ge2p1x520-ethip6-ip6scale200k-ndrpdrdisc

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x100k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 100k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-78B-1t1c-ethip6-ip6scale200k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 5341135.1875 pps (2x 2670567.59375 pps)
FINAL_BANDWIDTH: 4.187449987 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/69/456’, ‘10/70/493’]
LAT_50%NDR: [‘10/31/109’, ‘10/37/151’]
LAT_10%NDR: [‘10/24/119’, ‘10/22/103’]
tc02-78B-1t1c-ethip6-ip6scale200k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 5341135.1875 pps (2x 2670567.59375 pps)
FINAL_BANDWIDTH: 4.187449987 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/261/959’, ‘10/263/809’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip6-ip6scale200k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/406/430’, ‘20/592/599’]
LAT_50%NDR: [‘20/14/355’, ‘20/15/346’]
LAT_10%NDR: [‘10/27/161’, ‘10/27/124’]
tc04-1518B-1t1c-ethip6-ip6scale200k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/403/466’, ‘20/361/373’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip6-ip6scale200k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/318/392’, ‘60/481/510’]
LAT_50%NDR: [‘50/65/287’, ‘50/66/265’]
LAT_10%NDR: [‘50/61/160’, ‘50/62/246’]
tc06-9000B-1t1c-ethip6-ip6scale200k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/276/310’, ‘50/274/305’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-78B-2t2c-ethip6-ip6scale200k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 11273214.25 pps (2x 5636607.125 pps)
FINAL_BANDWIDTH: 8.838199972 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/137/527’, ‘10/859/1123’]
LAT_50%NDR: [‘10/18/99’, ‘10/19/84’]
LAT_10%NDR: [‘10/21/77’, ‘10/18/123’]
tc08-78B-2t2c-ethip6-ip6scale200k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 11668686.1875 pps (2x 5834343.09375 pps)
FINAL_BANDWIDTH: 9.148249971 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/92/279’, ‘10/791/1145’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip6-ip6scale200k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/332/346’, ‘20/255/267’]
LAT_50%NDR: [‘20/13/276’, ‘10/14/213’]
LAT_10%NDR: [‘20/26/60’, ‘10/24/176’]
tc10-1518B-2t2c-ethip6-ip6scale200k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/266/284’, ‘20/322/332’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip6-ip6scale200k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/208/452’, ‘50/65/147’]
LAT_50%NDR: [‘50/66/176’, ‘50/63/164’]
LAT_10%NDR: [‘50/62/168’, ‘50/62/76’]
tc12-9000B-2t2c-ethip6-ip6scale200k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/282/303’, ‘50/115/129’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-78B-4t4c-ethip6-ip6scale200k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 17205293.3125 pps (2x 8602646.65625 pps)
FINAL_BANDWIDTH: 13.488949957 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/126/351’, ‘20/105/391’]
LAT_50%NDR: [‘10/23/84’, ‘10/24/327’]
LAT_10%NDR: [‘10/20/55’, ‘10/21/54’]
tc14-78B-4t4c-ethip6-ip6scale200k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 18787181.0625 pps (2x 9393590.53125 pps)
FINAL_BANDWIDTH: 14.729149953 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/162/480’, ‘20/385/608’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip6-ip6scale200k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/247/275’, ‘20/81/90’]
LAT_50%NDR: [‘20/26/231’, ‘10/27/71’]
LAT_10%NDR: [‘10/27/54’, ‘10/27/45’]
tc16-1518B-4t4c-ethip6-ip6scale200k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/185/282’, ‘20/154/219’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip6-ip6scale200k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/194/245’, ‘60/183/259’]
LAT_50%NDR: [‘50/65/91’, ‘50/62/88’]
LAT_10%NDR: [‘50/61/107’, ‘50/58/88’]
tc18-9000B-4t4c-ethip6-ip6scale200k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/244/443’, ‘50/95/441’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.3.5. 10ge2p1x520-ethip6-ip6scale20k-ndrpdrdisc

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x10k static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 10k flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-78B-1t1c-ethip6-ip6scale20k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 6527551.0 pps (2x 3263775.5 pps)
FINAL_BANDWIDTH: 5.117599984 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/1908/3226’, ‘10/2919/3043’]
LAT_50%NDR: [‘10/30/100’, ‘10/31/74’]
LAT_10%NDR: [‘10/20/69’, ‘10/23/77’]
tc02-78B-1t1c-ethip6-ip6scale20k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 6527551.0 pps (2x 3263775.5 pps)
FINAL_BANDWIDTH: 5.117599984 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘40/1800/2004’, ‘40/2162/2283’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip6-ip6scale20k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/890/985’, ‘20/955/1066’]
LAT_50%NDR: [‘20/30/221’, ‘20/29/229’]
LAT_10%NDR: [‘20/26/235’, ‘10/25/201’]
tc04-1518B-1t1c-ethip6-ip6scale20k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/91/106’, ‘20/112/120’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip6-ip6scale20k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/381/437’, ‘60/385/405’]
LAT_50%NDR: [‘50/64/245’, ‘50/65/251’]
LAT_10%NDR: [‘50/62/115’, ‘50/62/203’]
tc06-9000B-1t1c-ethip6-ip6scale20k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/835/921’, ‘50/931/1012’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-78B-2t2c-ethip6-ip6scale20k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 13646045.875 pps (2x 6823022.9375 pps)
FINAL_BANDWIDTH: 10.698499966 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/57/218’, ‘20/822/991’]
LAT_50%NDR: [‘10/29/62’, ‘10/30/95’]
LAT_10%NDR: [‘10/19/43’, ‘10/19/47’]
tc08-78B-2t2c-ethip6-ip6scale20k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 13646045.875 pps (2x 6823022.9375 pps)
FINAL_BANDWIDTH: 10.698499966 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘30/62/173’, ‘20/1523/1574’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip6-ip6scale20k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/192/253’, ‘20/214/223’]
LAT_50%NDR: [‘20/27/163’, ‘10/27/195’]
LAT_10%NDR: [‘10/26/72’, ‘20/27/126’]
tc10-1518B-2t2c-ethip6-ip6scale20k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/76/108’, ‘20/309/338’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip6-ip6scale20k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/197/238’, ‘60/207/222’]
LAT_50%NDR: [‘50/64/104’, ‘50/65/235’]
LAT_10%NDR: [‘50/55/124’, ‘50/62/136’]
tc12-9000B-2t2c-ethip6-ip6scale20k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/188/244’, ‘50/118/146’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-78B-4t4c-ethip6-ip6scale20k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 21555484.625 pps (2x 10777742.3125 pps)
FINAL_BANDWIDTH: 16.899499946 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/750/791’, ‘10/775/792’]
LAT_50%NDR: [‘10/10/36’, ‘10/10/36’]
LAT_10%NDR: [‘10/20/57’, ‘10/19/103’]
tc14-78B-4t4c-ethip6-ip6scale20k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 21555484.625 pps (2x 10777742.3125 pps)
FINAL_BANDWIDTH: 16.899499946 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/409/456’, ‘20/615/697’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip6-ip6scale20k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/141/176’, ‘20/161/213’]
LAT_50%NDR: [‘20/28/213’, ‘20/27/146’]
LAT_10%NDR: [‘20/26/46’, ‘10/27/40’]
tc16-1518B-4t4c-ethip6-ip6scale20k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/278/366’, ‘20/73/81’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip6-ip6scale20k-ndrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/103/275’, ‘60/148/167’]
LAT_50%NDR: [‘50/66/293’, ‘50/66/112’]
LAT_10%NDR: [‘50/61/99’, ‘50/62/84’]
tc18-9000B-4t4c-ethip6-ip6scale20k-pdrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/69/273’, ‘50/70/227’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.3.6. 10ge2p1x520-ethip6-ip6scale2m-ndrpdrdisc

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and 2x1M static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 1M flows per flow-group) with all packets containing Ethernet header, IPv6 header withq IP and static payload. MAC addresses are matching MAC addresses of the TG node interfaces. Incrementing of IP.dst (IPv6 destination address) field is applied to both streams.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-78B-1t1c-ethip6-ip6scale2m-ndrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 4154719.375 pps (2x 2077359.6875 pps)
FINAL_BANDWIDTH: 3.25729999 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/487/2732’, ‘10/709/4583’]
LAT_50%NDR: [‘10/34/316’, ‘10/42/436’]
LAT_10%NDR: [‘10/21/59’, ‘10/27/133’]
tc02-78B-1t1c-ethip6-ip6scale2m-pdrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 4154719.375 pps (2x 2077359.6875 pps)
FINAL_BANDWIDTH: 3.25729999 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/735/2943’, ‘10/1139/4397’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip6-ip6scale2m-ndrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/121/145’, ‘20/115/125’]
LAT_50%NDR: [‘20/30/118’, ‘20/31/116’]
LAT_10%NDR: [‘20/27/48’, ‘10/28/47’]
tc04-1518B-1t1c-ethip6-ip6scale2m-pdrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/279/290’, ‘20/276/285’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip6-ip6scale2m-ndrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/129/151’, ‘50/156/175’]
LAT_50%NDR: [‘50/65/274’, ‘50/62/217’]
LAT_10%NDR: [‘50/61/93’, ‘50/60/76’]
tc06-9000B-1t1c-ethip6-ip6scale2m-pdrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/292/345’, ‘60/289/313’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-78B-2t2c-ethip6-ip6scale2m-ndrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 8900382.625 pps (2x 4450191.3125 pps)
FINAL_BANDWIDTH: 6.977899978 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/235/929’, ‘10/578/1590’]
LAT_50%NDR: [‘10/33/72’, ‘10/28/81’]
LAT_10%NDR: [‘10/22/92’, ‘10/23/87’]
tc08-78B-2t2c-ethip6-ip6scale2m-pdrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 8900382.625 pps (2x 4450191.3125 pps)
FINAL_BANDWIDTH: 6.977899978 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/166/711’, ‘10/466/1279’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip6-ip6scale2m-ndrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/304/324’, ‘20/237/252’]
LAT_50%NDR: [‘20/14/251’, ‘10/14/137’]
LAT_10%NDR: [‘20/27/54’, ‘10/27/156’]
tc10-1518B-2t2c-ethip6-ip6scale2m-pdrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/368/397’, ‘20/126/134’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip6-ip6scale2m-ndrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/120/147’, ‘50/256/274’]
LAT_50%NDR: [‘50/65/90’, ‘50/66/110’]
LAT_10%NDR: [‘50/61/168’, ‘50/62/161’]
tc12-9000B-2t2c-ethip6-ip6scale2m-pdrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/357/427’, ‘50/88/120’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-78B-4t4c-ethip6-ip6scale2m-ndrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 15623405.5625 pps (2x 7811702.78125 pps)
FINAL_BANDWIDTH: 12.248749961 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/93/277’, ‘10/270/818’]
LAT_50%NDR: [‘10/23/72’, ‘10/24/58’]
LAT_10%NDR: [‘10/23/69’, ‘10/21/51’]
tc14-78B-4t4c-ethip6-ip6scale2m-pdrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 16018877.5 pps (2x 8009438.75 pps)
FINAL_BANDWIDTH: 12.55879996 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/560/1102’, ‘20/1394/1662’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip6-ip6scale2m-ndrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/169/194’, ‘20/99/106’]
LAT_50%NDR: [‘20/27/106’, ‘10/27/44’]
LAT_10%NDR: [‘20/26/128’, ‘10/27/42’]
tc16-1518B-4t4c-ethip6-ip6scale2m-pdrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/56/612’, ‘20/161/683’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip6-ip6scale2m-ndrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/79/102’, ‘50/81/101’]
LAT_50%NDR: [‘50/66/114’, ‘50/66/283’]
LAT_10%NDR: [‘50/55/780’, ‘50/62/800’]
tc18-9000B-4t4c-ethip6-ip6scale2m-pdrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 277160.0 pps (2x 138580.0 pps)
FINAL_BANDWIDTH: 19.9998656 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/97/140’, ‘50/177/211’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.3.7. 40ge2p1xl710-ethip6-ip6base-ndrpdrdisc

RFC2544: Pkt throughput IPv6 routing test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6 for IPv6 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and two static IPv6 /64 route entries. DUT1 and DUT2 tested with 2p40GE NIC XL710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv6 header and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-78B-1t1c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 18.75Mpps rate, step 100kpps.
FINAL_RATE: 7485156.25 pps (2x 3742578.125 pps)
FINAL_BANDWIDTH: 5.8683625 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/56/226’, ‘20/58/219’]
LAT_50%NDR: [‘10/11/67’, ‘10/11/53’]
LAT_10%NDR: [‘10/22/47’, ‘10/21/104’]
tc03-1518B-1t1c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps.
FINAL_RATE: 3889574.21876 pps (2x 1944787.10938 pps)
FINAL_BANDWIDTH: 47.8573211876 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/34/273’, ‘10/33/256’]
LAT_50%NDR: [‘10/22/48’, ‘10/21/58’]
LAT_10%NDR: [‘10/22/45’, ‘10/23/47’]
tc07-78B-2t2c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 18.75Mpps rate, step 100kpps.
FINAL_RATE: 15061718.75 pps (2x 7530859.375 pps)
FINAL_BANDWIDTH: 11.8083875 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/49/158’, ‘20/50/146’]
LAT_50%NDR: [‘10/27/75’, ‘10/28/94’]
LAT_10%NDR: [‘10/20/37’, ‘10/20/49’]
tc09-1518B-2t2c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps.
FINAL_RATE: 3827661.03124 pps (2x 1913830.51562 pps)
FINAL_BANDWIDTH: 47.0955413284 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/34/57’, ‘10/34/67’]
LAT_50%NDR: [‘10/27/169’, ‘10/25/186’]
LAT_10%NDR: [‘10/22/47’, ‘10/23/75’]
tc13-78B-4t4c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 18.75Mpps rate, step 100kpps.
FINAL_RATE: 24386718.75 pps (2x 12193359.375 pps)
FINAL_BANDWIDTH: 19.1191875 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/26/203’, ‘10/26/85’]
LAT_50%NDR: [‘10/18/665’, ‘10/19/612’]
LAT_10%NDR: [‘10/20/35’, ‘10/19/67’]
tc15-1518B-4t4c-ethip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 24.5G rate, step 10kpps.
FINAL_RATE: 3889574.21876 pps (2x 1944787.10938 pps)
FINAL_BANDWIDTH: 47.8573211876 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/35/194’, ‘20/34/113’]
LAT_50%NDR: [‘10/27/78’, ‘10/26/52’]
LAT_10%NDR: [‘10/22/43’, ‘10/21/40’]

7.1.4. IPv4 Overlay Tunnels

Note

Data sources for reported test results: i) FD.io test executor jobs csit-vpp-perf-1701-all/4 , ii) archived FD.io jobs test result output files.

7.1.4.1. 10ge2p1x520-ethip4lispip4-ip4base-ndrpdrdisc

RFC6830: Pkt throughput Lisp test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv4 on DUT1-DUT2, Eth-IPv4 on TG-DUTn for IPv4 routing over LISPoIPv4 tunnel.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search
  • [Ref] Applicable standard specifications: RFC6830.
Name Documentation Message
tc01-64B-1t1c-ethip4lispip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 4836141.125 pps (2x 2418070.5625 pps)
FINAL_BANDWIDTH: 3.249886836 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/4300/4455’, ‘40/2806/2991’]
LAT_50%NDR: [‘10/42/104’, ‘10/39/176’]
LAT_10%NDR: [‘10/27/104’, ‘10/24/68’]
tc02-64B-1t1c-ethip4lispip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 4836141.125 pps (2x 2418070.5625 pps)
FINAL_BANDWIDTH: 3.249886836 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/4188/4457’, ‘20/2992/4464’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1480B-1t1c-ethip4lispip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1606642.0 pps (2x 803321.0 pps)
FINAL_BANDWIDTH: 19.279704 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/1369/1384’, ‘20/1370/1458’]
LAT_50%NDR: [‘20/32/102’, ‘20/35/97’]
LAT_10%NDR: [‘20/29/48’, ‘20/29/49’]
tc04-1480B-1t1c-ethip4lispip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1632233.0 pps (2x 816116.5 pps)
FINAL_BANDWIDTH: 19.586796 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/1372/1386’, ‘20/1372/1480’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip4lispip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 244801.5 pps (2x 122400.75 pps)
FINAL_BANDWIDTH: 17.66487624 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/73/251’, ‘50/75/262’]
LAT_50%NDR: [‘50/66/165’, ‘50/67/186’]
LAT_10%NDR: [‘50/63/121’, ‘50/63/137’]
tc06-9000B-1t1c-ethip4lispip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 276916.0 pps (2x 138458.0 pps)
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/1621/1829’, ‘60/1620/1710’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-ethip4lispip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 9261548.5625 pps (2x 4630774.28125 pps)
FINAL_BANDWIDTH: 6.223760634 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/63/248’, ‘20/77/203’]
LAT_50%NDR: [‘10/34/84’, ‘10/37/80’]
LAT_10%NDR: [‘10/20/37’, ‘10/20/37’]
tc08-64B-2t2c-ethip4lispip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 9472282.25 pps (2x 4736141.125 pps)
FINAL_BANDWIDTH: 6.365373672 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/928/968’, ‘20/954/991’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1480B-2t2c-ethip4lispip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1606642.0 pps (2x 803321.0 pps)
FINAL_BANDWIDTH: 19.279704 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/680/1377’, ‘20/680/1377’]
LAT_50%NDR: [‘20/29/164’, ‘20/30/61’]
LAT_10%NDR: [‘20/27/42’, ‘20/28/40’]
tc10-1480B-2t2c-ethip4lispip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1632233.0 pps (2x 816116.5 pps)
FINAL_BANDWIDTH: 19.586796 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/1359/1377’, ‘20/1359/1377’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip4lispip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 244801.5 pps (2x 122400.75 pps)
FINAL_BANDWIDTH: 17.66487624 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/71/156’, ‘50/74/111’]
LAT_50%NDR: [‘50/63/207’, ‘50/67/85’]
LAT_10%NDR: [‘50/56/81’, ‘50/62/102’]
tc12-9000B-2t2c-ethip4lispip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 276916.0 pps (2x 138458.0 pps)
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/1619/1781’, ‘50/1618/1748’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-ethip4lispip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 9261548.5625 pps (2x 4630774.28125 pps)
FINAL_BANDWIDTH: 6.223760634 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/62/126’, ‘10/64/111’]
LAT_50%NDR: [‘10/32/180’, ‘10/30/98’]
LAT_10%NDR: [‘10/21/51’, ‘10/21/60’]
tc14-64B-4t4c-ethip4lispip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 9472282.25 pps (2x 4736141.125 pps)
FINAL_BANDWIDTH: 6.365373672 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘30/943/1064’, ‘20/942/996’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1480B-4t4c-ethip4lispip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1606642.0 pps (2x 803321.0 pps)
FINAL_BANDWIDTH: 19.279704 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/2543/2594’, ‘20/2545/2607’]
LAT_50%NDR: [‘20/29/60’, ‘20/29/43’]
LAT_10%NDR: [‘20/27/43’, ‘20/28/179’]
tc16-1480B-4t4c-ethip4lispip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1480 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1632233.0 pps (2x 816116.5 pps)
FINAL_BANDWIDTH: 19.586796 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/2546/2576’, ‘20/2545/2605’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip4lispip4-ip4base-ndrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 244801.5 pps (2x 122400.75 pps)
FINAL_BANDWIDTH: 17.66487624 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/71/173’, ‘50/73/93’]
LAT_50%NDR: [‘50/66/188’, ‘50/66/90’]
LAT_10%NDR: [‘50/62/81’, ‘50/56/73’]
tc18-9000B-4t4c-ethip4lispip4-ip4base-pdrdisc
[Cfg] DUT runs IPv4 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 276916.0 pps (2x 138458.0 pps)
FINAL_BANDWIDTH: 19.98225856 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/2856/2938’, ‘60/2856/2956’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.4.2. 10ge2p1x520-ethip4lispip6-ip4base-ndrpdrdisc

RFC6830: Pkt throughput Lisp test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4-LISP-IPv6 on DUT1-DUT2 and Eth-IPv4 on TG-DUTn for IPv4 routing over LISPoIPv6 tunnel.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and static routes. LISPoIPv6 tunnel is configured between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search
  • [Ref] Applicable standard specifications: RFC6830.
Name Documentation Message
tc01-64B-1t1c-ethip4lispip6-ip4base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 4006439.0 pps (2x 2003219.5 pps)
FINAL_BANDWIDTH: 2.692327008 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/118/334’, ‘20/118/310’]
LAT_50%NDR: [‘10/27/86’, ‘10/48/128’]
LAT_10%NDR: [‘10/21/66’, ‘10/28/105’]
tc02-64B-1t1c-ethip4lispip6-ip4base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 4006439.0 pps (2x 2003219.5 pps)
FINAL_BANDWIDTH: 2.692327008 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/89/273’, ‘20/101/329’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1460B-1t1c-ethip4lispip6-ip4base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 1610872.0625 pps (2x 805436.03125 pps)
FINAL_BANDWIDTH: 19.07272522 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/51/290’, ‘20/52/288’]
LAT_50%NDR: [‘20/38/76’, ‘20/40/70’]
LAT_10%NDR: [‘20/29/204’, ‘20/29/163’]
tc04-1460B-1t1c-ethip4lispip6-ip4base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1610872.0625 pps (2x 805436.03125 pps)
FINAL_BANDWIDTH: 19.07272522 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/62/199’, ‘20/62/199’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip4lispip6-ip4base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 243732.25 pps (2x 121866.125 pps)
FINAL_BANDWIDTH: 17.58771916 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/76/145’, ‘60/77/148’]
LAT_50%NDR: [‘50/67/181’, ‘50/70/247’]
LAT_10%NDR: [‘50/61/92’, ‘50/64/74’]
tc06-9000B-1t1c-ethip4lispip6-ip4base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 275694.0 pps (2x 137847.0 pps)
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/1617/1843’, ‘60/1621/2461’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-ethip4lispip6-ip4base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 8398484.0 pps (2x 4199242.0 pps)
FINAL_BANDWIDTH: 5.643781248 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/1045/1119’, ‘20/1071/1114’]
LAT_50%NDR: [‘10/37/129’, ‘10/31/105’]
LAT_10%NDR: [‘10/20/79’, ‘10/31/97’]
tc08-64B-2t2c-ethip4lispip6-ip4base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 8398484.0 pps (2x 4199242.0 pps)
FINAL_BANDWIDTH: 5.643781248 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/1047/1087’, ‘20/1079/1212’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1460B-2t2c-ethip4lispip6-ip4base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1610872.0625 pps (2x 805436.03125 pps)
FINAL_BANDWIDTH: 19.07272522 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/37/161’, ‘20/35/110’]
LAT_50%NDR: [‘20/29/45’, ‘20/31/52’]
LAT_10%NDR: [‘20/14/61’, ‘20/14/77’]
tc10-1460B-2t2c-ethip4lispip6-ip4base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1610872.0625 pps (2x 805436.03125 pps)
FINAL_BANDWIDTH: 19.07272522 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/34/52’, ‘20/35/98’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip4lispip6-ip4base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 243732.25 pps (2x 121866.125 pps)
FINAL_BANDWIDTH: 17.58771916 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/73/88’, ‘50/75/88’]
LAT_50%NDR: [‘50/68/98’, ‘50/68/149’]
LAT_10%NDR: [‘50/57/84’, ‘50/63/116’]
tc12-9000B-2t2c-ethip4lispip6-ip4base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 275694.0 pps (2x 137847.0 pps)
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/1616/1665’, ‘60/1618/1812’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-ethip4lispip6-ip4base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 8398484.0 pps (2x 4199242.0 pps)
FINAL_BANDWIDTH: 5.643781248 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/1027/1067’, ‘10/1036/1152’]
LAT_50%NDR: [‘10/39/73’, ‘20/43/72’]
LAT_10%NDR: [‘10/23/94’, ‘10/25/73’]
tc14-64B-4t4c-ethip4lispip6-ip4base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 8398484.0 pps (2x 4199242.0 pps)
FINAL_BANDWIDTH: 5.643781248 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/1027/1074’, ‘10/1031/1095’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1460B-4t4c-ethip4lispip6-ip4base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1610872.0625 pps (2x 805436.03125 pps)
FINAL_BANDWIDTH: 19.07272522 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/36/152’, ‘20/35/100’]
LAT_50%NDR: [‘20/29/44’, ‘20/29/46’]
LAT_10%NDR: [‘20/27/60’, ‘20/28/43’]
tc16-1460B-4t4c-ethip4lispip6-ip4base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1610872.0625 pps (2x 805436.03125 pps)
FINAL_BANDWIDTH: 19.07272522 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/36/82’, ‘20/34/91’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip4lispip6-ip4base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 243732.25 pps (2x 121866.125 pps)
FINAL_BANDWIDTH: 17.58771916 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/73/135’, ‘50/75/111’]
LAT_50%NDR: [‘50/65/107’, ‘50/66/120’]
LAT_10%NDR: [‘50/63/97’, ‘50/57/83’]
tc18-9000B-4t4c-ethip4lispip6-ip4base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 275694.0 pps (2x 137847.0 pps)
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/2845/3363’, ‘60/2845/3343’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.4.3. 10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-ndrpdrdisc

RFC2544: Packet throughput L2BD with VXLANoIPv4 test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 bridge domain on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge domain. VXLAN tunnels are configured between L2BDs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name Documentation Message
tc01-64B-1t1c-ethip4vxlan-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 5967723.75 pps (2x 2983861.875 pps)
FINAL_BANDWIDTH: 4.01031036 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/3565/3663’, ‘20/2380/2454’]
LAT_50%NDR: [‘10/36/102’, ‘10/35/128’]
LAT_10%NDR: [‘10/24/77’, ‘10/25/67’]
tc02-64B-1t1c-ethip4vxlan-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 5967723.75 pps (2x 2983861.875 pps)
FINAL_BANDWIDTH: 4.01031036 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/3566/3683’, ‘20/2377/2457’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip4vxlan-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/158/276’, ‘20/252/419’]
LAT_50%NDR: [‘20/17/117’, ‘20/18/119’]
LAT_10%NDR: [‘20/28/83’, ‘20/29/60’]
tc04-1518B-1t1c-ethip4vxlan-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/287/380’, ‘20/110/292’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip4vxlan-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 275632.0 pps (2x 137816.0 pps)
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/242/406’, ‘60/202/369’]
LAT_50%NDR: [‘50/68/225’, ‘50/67/188’]
LAT_10%NDR: [‘50/62/115’, ‘50/58/99’]
tc06-9000B-1t1c-ethip4vxlan-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 275632.0 pps (2x 137816.0 pps)
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/279/315’, ‘50/114/417’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-ethip4vxlan-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 11158675.125 pps (2x 5579337.5625 pps)
FINAL_BANDWIDTH: 7.498629684 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/64/168’, ‘40/790/836’]
LAT_50%NDR: [‘10/34/76’, ‘10/33/69’]
LAT_10%NDR: [‘10/23/68’, ‘10/21/55’]
tc08-64B-2t2c-ethip4vxlan-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 11447061.3125 pps (2x 5723530.65625 pps)
FINAL_BANDWIDTH: 7.692425202 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/68/175’, ‘20/110/274’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip4vxlan-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/182/308’, ‘20/177/250’]
LAT_50%NDR: [‘20/30/214’, ‘20/31/81’]
LAT_10%NDR: [‘20/27/201’, ‘20/28/70’]
tc10-1518B-2t2c-ethip4vxlan-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/100/144’, ‘20/44/280’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip4vxlan-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 275632.0 pps (2x 137816.0 pps)
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/110/164’, ‘60/190/271’]
LAT_50%NDR: [‘50/66/91’, ‘50/66/146’]
LAT_10%NDR: [‘50/60/190’, ‘50/62/114’]
tc12-9000B-2t2c-ethip4vxlan-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 275632.0 pps (2x 137816.0 pps)
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/104/205’, ‘50/81/269’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-ethip4vxlan-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 18656716.0 pps (2x 9328358.0 pps)
FINAL_BANDWIDTH: 12.537313152 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/168/376’, ‘10/97/160’]
LAT_50%NDR: [‘10/24/117’, ‘10/23/185’]
LAT_10%NDR: [‘10/21/131’, ‘10/20/75’]
tc14-64B-4t4c-ethip4vxlan-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 18656716.0 pps (2x 9328358.0 pps)
FINAL_BANDWIDTH: 12.537313152 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/92/268’, ‘20/58/227’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip4vxlan-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/90/130’, ‘20/105/217’]
LAT_50%NDR: [‘20/28/64’, ‘20/30/144’]
LAT_10%NDR: [‘20/27/78’, ‘20/28/80’]
tc16-1518B-4t4c-ethip4vxlan-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/104/186’, ‘20/46/176’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip4vxlan-l2bdbasemaclrn-ndrdisc
[Cfg] DUT runs L2BD forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 275632.0 pps (2x 137816.0 pps)
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/93/309’, ‘50/78/175’]
LAT_50%NDR: [‘50/65/145’, ‘50/67/106’]
LAT_10%NDR: [‘50/62/117’, ‘50/59/97’]
tc18-9000B-4t4c-ethip4vxlan-l2bdbasemaclrn-pdrdisc
[Cfg] DUT runs L2BD forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 275632.0 pps (2x 137816.0 pps)
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/129/171’, ‘60/116/191’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.4.4. 10ge2p1x520-ethip4vxlan-l2xcbase-ndrpdrdisc

RFC2544: Pkt throughput L2XC with VXLANoIPv4 test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross-connect on TG-DUTn. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. VXLAN tunnels are configured between L2XCs on DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and generated payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name Documentation Message
tc01-64B-1t1c-ethip4vxlan-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 6544496.125 pps (2x 3272248.0625 pps)
FINAL_BANDWIDTH: 4.397901396 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/1441/1658’, ‘30/2127/2268’]
LAT_50%NDR: [‘10/34/136’, ‘10/31/143’]
LAT_10%NDR: [‘10/21/43’, ‘10/25/82’]
tc02-64B-1t1c-ethip4vxlan-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 6544496.125 pps (2x 3272248.0625 pps)
FINAL_BANDWIDTH: 4.397901396 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/3225/3379’, ‘20/2123/2275’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip4vxlan-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/135/473’, ‘20/104/291’]
LAT_50%NDR: [‘20/31/119’, ‘20/33/121’]
LAT_10%NDR: [‘20/28/47’, ‘20/29/51’]
tc04-1518B-1t1c-ethip4vxlan-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/301/498’, ‘20/225/558’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip4vxlan-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 275632.0 pps (2x 137816.0 pps)
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/121/587’, ‘60/99/545’]
LAT_50%NDR: [‘50/66/103’, ‘50/69/116’]
LAT_10%NDR: [‘50/62/99’, ‘50/63/88’]
tc06-9000B-1t1c-ethip4vxlan-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 275632.0 pps (2x 137816.0 pps)
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/126/274’, ‘60/189/254’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-ethip4vxlan-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 12312219.875 pps (2x 6156109.9375 pps)
FINAL_BANDWIDTH: 8.273811756 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/57/171’, ‘10/721/900’]
LAT_50%NDR: [‘10/24/100’, ‘10/28/215’]
LAT_10%NDR: [‘10/21/44’, ‘10/21/104’]
tc08-64B-2t2c-ethip4vxlan-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 12600606.0625 pps (2x 6300303.03125 pps)
FINAL_BANDWIDTH: 8.467607274 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/52/160’, ‘20/93/267’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip4vxlan-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/264/328’, ‘20/101/189’]
LAT_50%NDR: [‘20/27/199’, ‘20/30/208’]
LAT_10%NDR: [‘20/27/68’, ‘20/28/62’]
tc10-1518B-2t2c-ethip4vxlan-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/136/157’, ‘20/87/323’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip4vxlan-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 275632.0 pps (2x 137816.0 pps)
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘2/217/289’, ‘50/165/223’]
LAT_50%NDR: [‘50/65/171’, ‘50/64/116’]
LAT_10%NDR: [‘50/62/122’, ‘50/55/82’]
tc12-9000B-2t2c-ethip4vxlan-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 275632.0 pps (2x 137816.0 pps)
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/227/288’, ‘60/85/201’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-ethip4vxlan-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 18656716.0 pps (2x 9328358.0 pps)
FINAL_BANDWIDTH: 12.537313152 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/110/226’, ‘10/139/229’]
LAT_50%NDR: [‘10/24/206’, ‘10/22/89’]
LAT_10%NDR: [‘10/21/36’, ‘10/19/30’]
tc14-64B-4t4c-ethip4vxlan-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 18656716.0 pps (2x 9328358.0 pps)
FINAL_BANDWIDTH: 12.537313152 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/105/220’, ‘20/73/179’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip4vxlan-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/63/104’, ‘20/93/230’]
LAT_50%NDR: [‘20/28/54’, ‘20/29/161’]
LAT_10%NDR: [‘20/27/86’, ‘20/28/136’]
tc16-1518B-4t4c-ethip4vxlan-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/89/163’, ‘20/65/164’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip4vxlan-l2xcbase-ndrdisc
[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 275632.0 pps (2x 137816.0 pps)
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/174/228’, ‘60/88/275’]
LAT_50%NDR: [‘50/65/131’, ‘50/66/303’]
LAT_10%NDR: [‘50/60/101’, ‘50/62/260’]
tc18-9000B-4t4c-ethip4vxlan-l2xcbase-pdrdisc
[Cfg] DUT runs L2XC forwarding config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 275632.0 pps (2x 137816.0 pps)
FINAL_BANDWIDTH: 19.88960512 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/94/138’, ‘50/119/229’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.5. IPv6 Overlay Tunnels

Note

Data sources for reported test results: i) FD.io test executor jobs csit-vpp-perf-1701-all/4 , ii) archived FD.io jobs test result output files.

7.1.5.1. 10ge2p1x520-ethip6lispip4-ip6base-ndrpdrdisc

RFC6830: Pkt throughput Lisp test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6-LISP-IPv4 on DUT1-DUT2, Eth-IPv6 on TG-DUTn for IPv6 routing over LISPoIPv4 tunnel.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and static routes. LISPoIPv4 tunnel is configured between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search
  • [Ref] Applicable standard specifications: RFC6830.
Name Documentation Message
tc01-78B-1t1c-ethip6lispip4-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 4166395.15624 pps (2x 2083197.57812 pps)
FINAL_BANDWIDTH: 3.26645380249 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/219/456’, ‘20/231/428’]
LAT_50%NDR: [‘10/31/113’, ‘10/47/115’]
LAT_10%NDR: [‘10/21/40’, ‘10/27/110’]
tc02-78B-1t1c-ethip6lispip4-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 4166395.15624 pps (2x 2083197.57812 pps)
FINAL_BANDWIDTH: 3.26645380249 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/209/396’, ‘20/222/429’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1460B-1t1c-ethip6lispip4-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1636124.0 pps (2x 818062.0 pps)
FINAL_BANDWIDTH: 19.37170816 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/46/335’, ‘20/45/329’]
LAT_50%NDR: [‘20/34/210’, ‘20/34/181’]
LAT_10%NDR: [‘20/28/69’, ‘20/29/84’]
tc04-1460B-1t1c-ethip6lispip4-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1636124.0 pps (2x 818062.0 pps)
FINAL_BANDWIDTH: 19.37170816 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/44/376’, ‘20/46/388’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip6lispip4-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 275694.0 pps (2x 137847.0 pps)
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/79/223’, ‘50/82/219’]
LAT_50%NDR: [‘50/68/219’, ‘50/69/200’]
LAT_10%NDR: [‘50/63/189’, ‘50/63/184’]
tc06-9000B-1t1c-ethip6lispip4-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 275694.0 pps (2x 137847.0 pps)
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/82/334’, ‘60/80/347’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-78B-2t2c-ethip6lispip4-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 8661643.0 pps (2x 4330821.5 pps)
FINAL_BANDWIDTH: 6.790728112 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/132/669’, ‘10/1070/1121’]
LAT_50%NDR: [‘10/49/123’, ‘10/43/240’]
LAT_10%NDR: [‘10/25/100’, ‘10/26/76’]
tc08-78B-2t2c-ethip6lispip4-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 8661643.0 pps (2x 4330821.5 pps)
FINAL_BANDWIDTH: 6.790728112 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/512/1113’, ‘20/530/1110’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1460B-2t2c-ethip6lispip4-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
Search FAILED
tc10-1460B-2t2c-ethip6lispip4-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1636124.0 pps (2x 818062.0 pps)
FINAL_BANDWIDTH: 19.37170816 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/37/220’, ‘20/37/202’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip6lispip4-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 275694.0 pps (2x 137847.0 pps)
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘60/39/251’, ‘50/41/243’]
LAT_50%NDR: [‘50/65/96’, ‘50/68/222’]
LAT_10%NDR: [‘50/62/146’, ‘50/62/151’]
tc12-9000B-2t2c-ethip6lispip4-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 275694.0 pps (2x 137847.0 pps)
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/76/138’, ‘60/77/211’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-78B-4t4c-ethip6lispip4-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 8661643.0 pps (2x 4330821.5 pps)
FINAL_BANDWIDTH: 6.790728112 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/1021/1063’, ‘20/1026/1075’]
LAT_50%NDR: [‘10/32/61’, ‘10/27/62’]
LAT_10%NDR: [‘10/23/66’, ‘10/23/58’]
tc14-78B-4t4c-ethip6lispip4-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 8661643.0 pps (2x 4330821.5 pps)
FINAL_BANDWIDTH: 6.790728112 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/1020/1060’, ‘20/1026/1133’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1460B-4t4c-ethip6lispip4-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1636124.0 pps (2x 818062.0 pps)
FINAL_BANDWIDTH: 19.37170816 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/33/238’, ‘20/36/135’]
LAT_50%NDR: [‘20/29/70’, ‘20/30/272’]
LAT_10%NDR: [‘20/28/81’, ‘20/28/65’]
tc16-1460B-4t4c-ethip6lispip4-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1636124.0 pps (2x 818062.0 pps)
FINAL_BANDWIDTH: 19.37170816 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/36/219’, ‘20/36/270’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip6lispip4-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 275694.0 pps (2x 137847.0 pps)
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/75/127’, ‘60/77/206’]
LAT_50%NDR: [‘50/66/125’, ‘50/67/280’]
LAT_10%NDR: [‘50/63/126’, ‘50/63/86’]
tc18-9000B-4t4c-ethip6lispip4-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 275694.0 pps (2x 137847.0 pps)
FINAL_BANDWIDTH: 19.89407904 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/78/205’, ‘50/78/284’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.5.2. 10ge2p1x520-ethip6lispip6-ip6base-ndrpdrdisc

RFC6830: Pkt throughput Lisp test cases

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv6-LISP-IPv6 on DUT1-DUT2, Eth-IPv6 on TG-DUTn for IPv6 routing over LISPoIPv6 tunnel.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv6 routing and static routes. LISPoIPv6 tunnel is configured between DUT1 and DUT2. DUT1 and DUT2 tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search
  • [Ref] Applicable standard specifications: RFC6830.
Name Documentation Message
tc01-78B-1t1c-ethip6lispip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 3488502.125 pps (2x 1744251.0625 pps)
FINAL_BANDWIDTH: 2.734985666 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/46/388’, ‘10/48/393’]
LAT_50%NDR: [‘10/49/226’, ‘10/49/200’]
LAT_10%NDR: [‘10/23/85’, ‘10/26/87’]
tc02-78B-1t1c-ethip6lispip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 3488502.125 pps (2x 1744251.0625 pps)
FINAL_BANDWIDTH: 2.734985666 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/108/334’, ‘20/111/310’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1460B-1t1c-ethip6lispip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1602288.53125 pps (2x 801144.265625 pps)
FINAL_BANDWIDTH: 18.97109621 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/57/309’, ‘20/57/304’]
LAT_50%NDR: [‘20/40/83’, ‘20/42/124’]
LAT_10%NDR: [‘20/30/269’, ‘20/30/277’]
tc04-1460B-1t1c-ethip6lispip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1628227.6875 pps (2x 814113.84375 pps)
FINAL_BANDWIDTH: 19.27821582 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/1385/1538’, ‘20/1387/1538’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-9000B-1t1c-ethip6lispip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 244801.5 pps (2x 122400.75 pps)
FINAL_BANDWIDTH: 17.66487624 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/77/260’, ‘50/77/265’]
LAT_50%NDR: [‘50/67/116’, ‘50/67/104’]
LAT_10%NDR: [‘50/58/103’, ‘50/65/101’]
tc06-9000B-1t1c-ethip6lispip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 244801.5 pps (2x 122400.75 pps)
FINAL_BANDWIDTH: 17.66487624 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/77/157’, ‘50/77/146’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-78B-2t2c-ethip6lispip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 7142393.375 pps (2x 3571196.6875 pps)
FINAL_BANDWIDTH: 5.599636406 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/72/225’, ‘20/120/313’]
LAT_50%NDR: [‘10/42/101’, ‘10/45/145’]
LAT_10%NDR: [‘10/13/102’, ‘10/13/73’]
tc08-78B-2t2c-ethip6lispip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 7142393.375 pps (2x 3571196.6875 pps)
FINAL_BANDWIDTH: 5.599636406 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘10/55/91’, ‘20/71/110’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1460B-2t2c-ethip6lispip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1602288.53125 pps (2x 801144.265625 pps)
FINAL_BANDWIDTH: 18.97109621 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/47/264’, ‘20/47/89’]
LAT_50%NDR: [‘20/29/45’, ‘20/30/120’]
LAT_10%NDR: [‘20/27/75’, ‘20/28/132’]
tc10-1460B-2t2c-ethip6lispip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1628227.6875 pps (2x 814113.84375 pps)
FINAL_BANDWIDTH: 19.27821582 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/1369/1440’, ‘20/1370/1562’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-9000B-2t2c-ethip6lispip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 244801.5 pps (2x 122400.75 pps)
FINAL_BANDWIDTH: 17.66487624 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/73/149’, ‘50/75/89’]
LAT_50%NDR: [‘50/68/235’, ‘50/69/126’]
LAT_10%NDR: [‘50/63/209’, ‘50/65/106’]
tc12-9000B-2t2c-ethip6lispip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 244801.5 pps (2x 122400.75 pps)
FINAL_BANDWIDTH: 17.66487624 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/73/89’, ‘50/75/94’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-78B-4t4c-ethip6lispip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 7873171.625 pps (2x 3936585.8125 pps)
FINAL_BANDWIDTH: 6.172566554 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/35/237’, ‘10/35/191’]
LAT_50%NDR: [‘10/21/122’, ‘10/45/84’]
LAT_10%NDR: [‘10/20/50’, ‘10/23/66’]
tc14-78B-4t4c-ethip6lispip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 78 Byte frames using binary search start at 10GE linerate, step 100kpps, LT=0.5%.
FINAL_RATE: 7873171.625 pps (2x 3936585.8125 pps)
FINAL_BANDWIDTH: 6.172566554 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘30/61/191’, ‘10/59/89’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1460B-4t4c-ethip6lispip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1460 Byte frames using binary search start at 10GE linerate, step 100kpps.
FINAL_RATE: 1602288.53125 pps (2x 801144.265625 pps)
FINAL_BANDWIDTH: 18.97109621 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/35/157’, ‘20/35/61’]
LAT_50%NDR: [‘20/29/51’, ‘20/31/48’]
LAT_10%NDR: [‘20/13/59’, ‘20/14/55’]
tc16-1460B-4t4c-ethip6lispip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1460 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1628227.6875 pps (2x 814113.84375 pps)
FINAL_BANDWIDTH: 19.27821582 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/1293/2614’, ‘20/1292/2646’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-9000B-4t4c-ethip6lispip6-ip6base-ndrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps.
FINAL_RATE: 244801.5 pps (2x 122400.75 pps)
FINAL_BANDWIDTH: 17.66487624 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘50/74/245’, ‘50/76/113’]
LAT_50%NDR: [‘50/66/86’, ‘50/67/95’]
LAT_10%NDR: [‘50/63/77’, ‘50/60/78’]
tc18-9000B-4t4c-ethip6lispip6-ip6base-pdrdisc
[Cfg] DUT runs IPv6 LISP remote static mappings and whitelist filters config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 9000 Byte frames using binary search start at 10GE linerate, step 5kpps, LT=0.5%.
FINAL_RATE: 244801.5 pps (2x 122400.75 pps)
FINAL_BANDWIDTH: 17.66487624 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘60/73/115’, ‘60/75/225’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.6. VM Vhost Connections

Note

Data sources for reported test results: i) FD.io test executor jobs csit-vpp-perf-1701-all/4 , ii) archived FD.io jobs test result output files.

7.1.6.1. 10ge2p1x520-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrpdrdisc

RFC2544: Packet throughput L2BD test cases with vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. 802.1q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 2515134.86328 pps (2x 1257567.43164 pps)
FINAL_BANDWIDTH: 1.69017062812 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/209/467’, ‘20/234/464’]
LAT_50%NDR: [‘10/61/213’, ‘10/70/211’]
LAT_10%NDR: [‘10/12/86’, ‘10/16/124’]
tc02-64B-1t1c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 2626029.7461 pps (2x 1313014.87305 pps)
FINAL_BANDWIDTH: 1.76469198938 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/379/625’, ‘20/437/711’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1195932.65625 pps (2x 597966.328125 pps)
FINAL_BANDWIDTH: 14.7147554025 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/346/579’, ‘20/392/607’]
LAT_50%NDR: [‘20/97/342’, ‘20/107/489’]
LAT_10%NDR: [‘20/36/140’, ‘20/38/179’]
tc04-1518B-1t1c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1245972.34375 pps (2x 622986.171875 pps)
FINAL_BANDWIDTH: 15.3304437175 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/677/1002’, ‘30/815/1096’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-IMIX-1t1c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 framesize using binary search start at 10GE linerate, step 10kpps. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 1952620.50781 pps (2x 976310.253906 pps)
FINAL_BANDWIDTH: 5.83963701329 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc06-IMIX-1t1c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 framesize using binary search start at 10GE linerate, step 10kpps, LT=0.5%. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 2132998.42188 pps (2x 1066499.21094 pps)
FINAL_BANDWIDTH: 6.37908722349 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 4733032.51954 pps (2x 2366516.25977 pps)
FINAL_BANDWIDTH: 3.18059785313 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/97/251’, ‘20/137/293’]
LAT_50%NDR: [‘10/33/177’, ‘10/36/180’]
LAT_10%NDR: [‘10/32/155’, ‘10/33/149’]
tc08-64B-2t2c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 5342954.375 pps (2x 2671477.1875 pps)
FINAL_BANDWIDTH: 3.59046534 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘30/122/981’, ‘30/230/995’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘2/241/265’, ‘20/167/284’]
LAT_50%NDR: [‘20/53/168’, ‘20/58/229’]
LAT_10%NDR: [‘20/34/214’, ‘20/34/163’]
tc10-1518B-2t2c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/89/669’, ‘20/82/647’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-IMIX-2t2c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 framesize using binary search start at 10GE linerate, step 10kpps. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 3807936.19532 pps (2x 1903968.09766 pps)
FINAL_BANDWIDTH: 11.3882677466 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc12-IMIX-2t2c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 framesize using binary search start at 10GE linerate, step 10kpps. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 4245996.84376 pps (2x 2122998.42188 pps)
FINAL_BANDWIDTH: 12.6983611142 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 4649861.35742 pps (2x 2324930.67871 pps)
FINAL_BANDWIDTH: 3.12470683219 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/58/152’, ‘10/86/196’]
LAT_50%NDR: [‘10/35/114’, ‘10/40/127’]
LAT_10%NDR: [‘10/27/131’, ‘10/31/128’]
tc14-64B-4t4c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 6784587.85156 pps (2x 3392293.92578 pps)
FINAL_BANDWIDTH: 4.55924303625 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/127/249’, ‘30/209/323’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/175/194’, ‘20/156/203’]
LAT_50%NDR: [‘20/45/159’, ‘20/52/182’]
LAT_10%NDR: [‘20/31/129’, ‘20/34/201’]
tc16-1518B-4t4c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/200/217’, ‘20/139/241’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-IMIX-4t4c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for IMIX_v4_1 framesize using binary search start at 10GE linerate, step 10kpps. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 4426374.75782 pps (2x 2213187.37891 pps)
FINAL_BANDWIDTH: 13.2378113244 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc18-IMIX-4t4c-dot1q-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for IMIX_v4_1 framesize using binary search start at 10GE linerate, step 10kpps, LT=0.5%. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 5302496.05468 pps (2x 2651248.02734 pps)
FINAL_BANDWIDTH: 15.8579980595 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.6.2. 10ge2p1x520-dot1q-l2xcbase-eth-2vhost-1vm-ndrpdrdisc

RFC2544: Pkt throughput L2XC test cases with vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect. 802.1q tagging is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 2792372.07032 pps (2x 1396186.03516 pps)
FINAL_BANDWIDTH: 1.87647403126 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/158/435’, ‘30/176/462’]
LAT_50%NDR: [‘10/67/210’, ‘10/62/190’]
LAT_10%NDR: [‘10/24/99’, ‘10/29/153’]
tc02-64B-1t1c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 2875543.23242 pps (2x 1437771.61621 pps)
FINAL_BANDWIDTH: 1.93236505219 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/227/435’, ‘30/261/434’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1245972.34375 pps (2x 622986.171875 pps)
FINAL_BANDWIDTH: 15.3304437175 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/283/557’, ‘30/323/553’]
LAT_50%NDR: [‘20/120/423’, ‘20/132/430’]
LAT_10%NDR: [‘20/34/141’, ‘20/38/200’]
tc04-1518B-1t1c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1321031.875 pps (2x 660515.9375 pps)
FINAL_BANDWIDTH: 16.25397619 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/1103/1390’, ‘20/1280/1575’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-IMIX-1t1c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 framesize using binary search start at 10GE linerate, step 10kpps. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 2210303.24218 pps (2x 1105151.62109 pps)
FINAL_BANDWIDTH: 6.61028017067 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc06-IMIX-1t1c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 framesize using binary search start at 10GE linerate, step 10kpps, LT=0.5%. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 2210303.24218 pps (2x 1105151.62109 pps)
FINAL_BANDWIDTH: 6.61028017067 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 4677585.07812 pps (2x 2338792.53906 pps)
FINAL_BANDWIDTH: 3.1433371725 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/85/180’, ‘20/101/201’]
LAT_50%NDR: [‘10/46/157’, ‘10/51/173’]
LAT_10%NDR: [‘10/33/162’, ‘10/32/181’]
tc08-64B-2t2c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 5980599.95118 pps (2x 2990299.97559 pps)
FINAL_BANDWIDTH: 4.01896316719 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘40/99/248’, ‘40/197/322’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/177/199’, ‘30/156/204’]
LAT_50%NDR: [‘20/47/174’, ‘20/52/187’]
LAT_10%NDR: [‘20/33/224’, ‘20/33/168’]
tc10-1518B-2t2c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘30/193/292’, ‘20/233/262’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-IMIX-2t2c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 framesize using binary search start at 10GE linerate, step 10kpps. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 3911009.28906 pps (2x 1955504.64453 pps)
FINAL_BANDWIDTH: 11.6965250095 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc12-IMIX-2t2c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 framesize using binary search start at 10GE linerate, step 10kpps, LT=0.5%. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 4658289.21876 pps (2x 2329144.60938 pps)
FINAL_BANDWIDTH: 13.931390166 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 5952876.23046 pps (2x 2976438.11523 pps)
FINAL_BANDWIDTH: 4.00033282687 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/51/133’, ‘20/78/170’]
LAT_50%NDR: [‘10/36/115’, ‘10/50/145’]
LAT_10%NDR: [‘10/24/106’, ‘10/30/125’]
tc14-64B-4t4c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 7477680.86914 pps (2x 3738840.43457 pps)
FINAL_BANDWIDTH: 5.02500154406 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘30/98/194’, ‘20/168/291’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/183/196’, ‘20/132/284’]
LAT_50%NDR: [‘20/42/129’, ‘20/49/156’]
LAT_10%NDR: [‘20/33/151’, ‘20/33/243’]
tc16-1518B-4t4c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1621270.0 pps (2x 810635.0 pps)
FINAL_BANDWIDTH: 19.94810608 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/155/176’, ‘20/130/200’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-IMIX-4t4c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for IMIX_v4_1 framesize using binary search start at 10GE linerate, step 10kpps. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 4529447.85156 pps (2x 2264723.92578 pps)
FINAL_BANDWIDTH: 13.5460685873 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc18-IMIX-4t4c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for IMIX_v4_1 framesize using binary search start at 10GE linerate, step 10kpps, LT=0.5%. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 5689020.15624 pps (2x 2844510.07812 pps)
FINAL_BANDWIDTH: 17.0139627956 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.6.3. 10ge2p1x520-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrpdrdisc

RFC2544: Pkt throughput L2BD test cases with vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 2750213.84376 pps (2x 1375106.92188 pps)
FINAL_BANDWIDTH: 1.84814370301 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/161/343’, ‘30/156/329’]
LAT_50%NDR: [‘10/71/201’, ‘10/69/229’]
LAT_10%NDR: [‘10/25/75’, ‘10/30/146’]
tc02-64B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 2895437.98438 pps (2x 1447718.99219 pps)
FINAL_BANDWIDTH: 1.9457343255 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/316/495’, ‘20/303/508’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1299371.65625 pps (2x 649685.828125 pps)
FINAL_BANDWIDTH: 15.9874688585 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/548/802’, ‘40/538/799’]
LAT_50%NDR: [‘20/83/306’, ‘20/77/295’]
LAT_10%NDR: [‘20/35/619’, ‘20/37/588’]
tc04-1518B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1324457.375 pps (2x 662228.6875 pps)
FINAL_BANDWIDTH: 16.296123542 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/2805/3013’, ‘30/2806/3096’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-IMIX-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 2285898.6875 pps (2x 1142949.34375 pps)
FINAL_BANDWIDTH: 6.83636094713 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc06-IMIX-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 2259853.875 pps (2x 1129926.9375 pps)
FINAL_BANDWIDTH: 6.75846959524 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 4986665.60938 pps (2x 2493332.80469 pps)
FINAL_BANDWIDTH: 3.3510392895 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/83/153’, ‘20/100/178’]
LAT_50%NDR: [‘10/45/158’, ‘10/53/181’]
LAT_10%NDR: [‘10/27/87’, ‘10/25/90’]
tc08-64B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 5887055.28124 pps (2x 2943527.64062 pps)
FINAL_BANDWIDTH: 3.95610114899 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/105/172’, ‘20/197/357’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/87/187’, ‘20/98/208’]
LAT_50%NDR: [‘20/47/164’, ‘20/52/262’]
LAT_10%NDR: [‘20/32/201’, ‘20/32/156’]
tc10-1518B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/220/254’, ‘20/243/278’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-IMIX-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 4082990.75 pps (2x 2041495.375 pps)
FINAL_BANDWIDTH: 12.2108642275 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc12-IMIX-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 4603887.0 pps (2x 2301943.5 pps)
FINAL_BANDWIDTH: 13.7686912652 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 5654696.65624 pps (2x 2827348.32812 pps)
FINAL_BANDWIDTH: 3.79995615299 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/54/133’, ‘20/74/159’]
LAT_50%NDR: [‘10/39/137’, ‘10/48/142’]
LAT_10%NDR: [‘10/23/75’, ‘10/27/148’]
tc14-64B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 7571655.3125 pps (2x 3785827.65625 pps)
FINAL_BANDWIDTH: 5.08815237 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/80/165’, ‘20/184/320’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/152/559’, ‘20/187/647’]
LAT_50%NDR: [‘20/42/200’, ‘20/49/231’]
LAT_10%NDR: [‘20/32/130’, ‘20/34/157’]
tc16-1518B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/181/191’, ‘20/210/226’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-IMIX-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 5228962.5 pps (2x 2614481.25 pps)
FINAL_BANDWIDTH: 15.6380837106 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc18-IMIX-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 5801948.375 pps (2x 2900974.1875 pps)
FINAL_BANDWIDTH: 17.3516934521 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.6.4. 10ge2p1x520-eth-l2xcbase-eth-2vhost-1vm-ndrpdrdisc

RFC2544: Pkt throughput L2XC test cases with vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 cross connect.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 cross- connect. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 3185886.26562 pps (2x 1592943.13281 pps)
FINAL_BANDWIDTH: 2.1409155705 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/156/296’, ‘20/146/279’]
LAT_50%NDR: [‘10/58/214’, ‘10/60/234’]
LAT_10%NDR: [‘10/26/115’, ‘10/30/129’]
tc02-64B-1t1c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 3243975.92188 pps (2x 1621987.96094 pps)
FINAL_BANDWIDTH: 2.1799518195 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/231/404’, ‘20/223/437’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1374628.8125 pps (2x 687314.40625 pps)
FINAL_BANDWIDTH: 16.913432909 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/866/1088’, ‘20/862/1091’]
LAT_50%NDR: [‘20/81/308’, ‘20/81/316’]
LAT_10%NDR: [‘20/34/144’, ‘20/35/180’]
tc04-1518B-1t1c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1399714.53125 pps (2x 699857.265625 pps)
FINAL_BANDWIDTH: 17.2220875925 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘30/921/1232’, ‘30/911/1229’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-IMIX-1t1c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 2416122.75 pps (2x 1208061.375 pps)
FINAL_BANDWIDTH: 7.22581770657 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc06-IMIX-1t1c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2XC switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 2546346.8125 pps (2x 1273173.40625 pps)
FINAL_BANDWIDTH: 7.61527446601 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 5073800.09376 pps (2x 2536900.04688 pps)
FINAL_BANDWIDTH: 3.40959366301 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/59/169’, ‘20/72/212’]
LAT_50%NDR: [‘10/40/121’, ‘10/48/162’]
LAT_10%NDR: [‘10/24/78’, ‘10/33/183’]
tc08-64B-2t2c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 6613175.98438 pps (2x 3306587.99219 pps)
FINAL_BANDWIDTH: 4.4440542615 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘30/89/168’, ‘20/155/301’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/210/230’, ‘20/246/254’]
LAT_50%NDR: [‘20/43/162’, ‘20/46/161’]
LAT_10%NDR: [‘20/33/150’, ‘20/33/192’]
tc10-1518B-2t2c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/202/210’, ‘20/220/229’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-IMIX-2t2c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 3952766.6875 pps (2x 1976383.34375 pps)
FINAL_BANDWIDTH: 11.821407468 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc12-IMIX-2t2c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2XC switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 5072693.625 pps (2x 2536346.8125 pps)
FINAL_BANDWIDTH: 15.1707355992 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 5945144.9375 pps (2x 2972572.46875 pps)
FINAL_BANDWIDTH: 3.995137398 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/42/112’, ‘10/66/158’]
LAT_50%NDR: [‘10/16/99’, ‘10/18/119’]
LAT_10%NDR: [‘10/24/87’, ‘10/26/80’]
tc14-64B-4t4c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 8443000.15624 pps (2x 4221500.07812 pps)
FINAL_BANDWIDTH: 5.67369610499 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/76/145’, ‘30/152/262’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/175/185’, ‘30/204/222’]
LAT_50%NDR: [‘20/40/124’, ‘20/46/174’]
LAT_10%NDR: [‘20/32/131’, ‘20/32/175’]
tc16-1518B-4t4c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘30/235/259’, ‘20/214/231’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-IMIX-4t4c-eth-l2xcbase-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 5463365.8125 pps (2x 2731682.90625 pps)
FINAL_BANDWIDTH: 16.3391058776 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc18-IMIX-4t4c-eth-l2xcbase-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2XC switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 6218665.375 pps (2x 3109332.6875 pps)
FINAL_BANDWIDTH: 18.5979550823 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.6.5. 10ge2p1x520-ethip4-ip4base-eth-2vhost-1vm-ndrpdrdisc

RFC2544: Pkt throughput IPv4 test cases with vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for IPv4 routing.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with IPv4 routing and two static IPv4 /24 route entries. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to mac, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-ethip4-ip4base-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 2604989.70312 pps (2x 1302494.85156 pps)
FINAL_BANDWIDTH: 1.7505530805 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/188/446’, ‘20/190/473’]
LAT_50%NDR: [‘10/67/200’, ‘10/73/214’]
LAT_10%NDR: [‘10/26/125’, ‘10/32/187’]
tc02-64B-1t1c-ethip4-ip4base-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 2663079.35938 pps (2x 1331539.67969 pps)
FINAL_BANDWIDTH: 1.7895893295 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/362/635’, ‘20/364/666’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip4-ip4base-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1249200.21875 pps (2x 624600.109375 pps)
FINAL_BANDWIDTH: 15.3701594915 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/615/1112’, ‘30/613/1120’]
LAT_50%NDR: [‘20/137/429’, ‘20/132/412’]
LAT_10%NDR: [‘20/36/170’, ‘20/37/178’]
tc04-1518B-1t1c-ethip4-ip4base-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1299371.65625 pps (2x 649685.828125 pps)
FINAL_BANDWIDTH: 15.9874688585 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/1510/1856’, ‘60/1488/1779’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-IMIX-1t1c-ethip4-ip4base-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 2103585.0 pps (2x 1051792.5 pps)
FINAL_BANDWIDTH: 6.2911214839 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc06-IMIX-1t1c-ethip4-ip4base-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs IPv4 routing config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 2155674.625 pps (2x 1077837.3125 pps)
FINAL_BANDWIDTH: 6.44690418768 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-ethip4-ip4base-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 5044755.26562 pps (2x 2522377.63281 pps)
FINAL_BANDWIDTH: 3.3900755385 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘40/100/181’, ‘60/131/221’]
LAT_50%NDR: [‘10/56/153’, ‘10/69/205’]
LAT_10%NDR: [‘10/29/112’, ‘10/39/175’]
tc08-64B-2t2c-ethip4-ip4base-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 5451382.85938 pps (2x 2725691.42969 pps)
FINAL_BANDWIDTH: 3.6633292815 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/115/193’, ‘20/256/410’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip4-ip4base-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/243/257’, ‘20/310/318’]
LAT_50%NDR: [‘20/51/184’, ‘20/56/222’]
LAT_10%NDR: [‘20/35/161’, ‘20/34/173’]
tc10-1518B-2t2c-ethip4-ip4base-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/222/250’, ‘20/256/262’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-IMIX-2t2c-ethip4-ip4base-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 3926721.875 pps (2x 1963360.9375 pps)
FINAL_BANDWIDTH: 11.7435161161 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc12-IMIX-2t2c-ethip4-ip4base-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs IPv4 routing config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 4317394.0625 pps (2x 2158697.03125 pps)
FINAL_BANDWIDTH: 12.9118863945 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-ethip4-ip4base-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 5567562.17188 pps (2x 2783781.08594 pps)
FINAL_BANDWIDTH: 3.7414017795 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/66/157’, ‘20/92/195’]
LAT_50%NDR: [‘10/41/157’, ‘10/49/170’]
LAT_10%NDR: [‘10/25/92’, ‘10/25/135’]
tc14-64B-4t4c-ethip4-ip4base-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 7019803.57812 pps (2x 3509901.78906 pps)
FINAL_BANDWIDTH: 4.7173080045 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/94/175’, ‘30/226/399’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip4-ip4base-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/161/177’, ‘20/184/205’]
LAT_50%NDR: [‘20/45/142’, ‘20/48/174’]
LAT_10%NDR: [‘20/33/136’, ‘20/33/142’]
tc16-1518B-4t4c-ethip4-ip4base-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/155/171’, ‘20/169/189’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-IMIX-4t4c-ethip4-ip4base-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 4786200.6875 pps (2x 2393100.34375 pps)
FINAL_BANDWIDTH: 14.3139307285 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc18-IMIX-4t4c-ethip4-ip4base-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs IPv4 routing config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 5489410.625 pps (2x 2744705.3125 pps)
FINAL_BANDWIDTH: 16.4169972294 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.6.6. 10ge2p1x520-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-ndrpdrdisc

RFC2544: Packet throughput L2BD test cases with VXLANoIPv4 and vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4. Eth-IPv4-VXLAN-Eth-IPv4 is applied on link between DUT1 and DUT2.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus 5-9 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X520 Niantic by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544, RFC7348.
Name Documentation Message
tc01-64B-1t1c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 2203990.15624 pps (2x 1101995.07812 pps)
FINAL_BANDWIDTH: 1.48108138499 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/256/1220’, ‘20/282/1368’]
LAT_50%NDR: [‘10/69/258’, ‘10/74/240’]
LAT_10%NDR: [‘10/26/85’, ‘10/33/160’]
tc02-64B-1t1c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 2276789.82812 pps (2x 1138394.91406 pps)
FINAL_BANDWIDTH: 1.5300027645 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/447/692’, ‘20/507/708’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1088585.375 pps (2x 544292.6875 pps)
FINAL_BANDWIDTH: 13.393954454 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/522/899’, ‘30/612/1014’]
LAT_50%NDR: [‘20/139/464’, ‘20/160/446’]
LAT_10%NDR: [‘20/37/203’, ‘20/36/177’]
tc04-1518B-1t1c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1137157.4375 pps (2x 568578.71875 pps)
FINAL_BANDWIDTH: 13.991585111 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/907/1250’, ‘30/1078/1393’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-IMIX-1t1c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 framesize using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 1811120.09375 pps (2x 905560.046875 pps)
FINAL_BANDWIDTH: 5.41645644541 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc06-IMIX-1t1c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 1857046.25 pps (2x 928523.125 pps)
FINAL_BANDWIDTH: 5.55380626881 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 4096781.625 pps (2x 2048390.8125 pps)
FINAL_BANDWIDTH: 2.753037252 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘40/121/245’, ‘20/144/264’]
LAT_50%NDR: [‘10/43/177’, ‘10/86/217’]
LAT_10%NDR: [‘10/29/111’, ‘10/41/196’]
tc08-64B-2t2c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 4533579.65624 pps (2x 2266789.82812 pps)
FINAL_BANDWIDTH: 3.04656552899 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘40/128/236’, ‘40/216/372’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/249/298’, ‘20/168/400’]
LAT_50%NDR: [‘20/56/205’, ‘20/61/209’]
LAT_10%NDR: [‘20/37/202’, ‘20/35/224’]
tc10-1518B-2t2c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/167/211’, ‘30/171/216’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-IMIX-2t2c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 2936310.92188 pps (2x 1468155.46094 pps)
FINAL_BANDWIDTH: 8.78152711873 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc12-IMIX-2t2c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 3694092.5 pps (2x 1847046.25 pps)
FINAL_BANDWIDTH: 11.0477992048 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 4642779.16406 pps (2x 2321389.58203 pps)
FINAL_BANDWIDTH: 3.11994759825 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘2/64/148’, ‘30/92/188’]
LAT_50%NDR: [‘10/22/157’, ‘10/25/139’]
LAT_10%NDR: [‘10/25/118’, ‘10/34/196’]
tc14-64B-4t4c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 5734774.24218 pps (2x 2867387.12109 pps)
FINAL_BANDWIDTH: 3.85376829074 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘40/154/240’, ‘30/200/325’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/146/178’, ‘20/154/217’]
LAT_50%NDR: [‘20/47/220’, ‘20/58/171’]
LAT_10%NDR: [‘20/35/152’, ‘20/36/178’]
tc16-1518B-4t4c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1574306.0 pps (2x 787153.0 pps)
FINAL_BANDWIDTH: 19.370261024 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/148/185’, ‘30/149/208’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-IMIX-4t4c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 4130390.98438 pps (2x 2065195.49219 pps)
FINAL_BANDWIDTH: 12.3526225271 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc18-IMIX-4t4c-ethip4vxlan-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B;16x570B;4x1518B)
FINAL_RATE: 4543726.39062 pps (2x 2271863.19531 pps)
FINAL_BANDWIDTH: 13.5887709377 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.6.7. 10ge2p1x710-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrpdrdisc

RFC2544: Pkt throughput L2BD test cases with vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus on NUMA1 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p10GE NIC X710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 2808303.5 pps (2x 1404151.75 pps)
FINAL_BANDWIDTH: 1.887179952 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/152/333’, ‘20/147/346’]
LAT_50%NDR: [‘10/76/217’, ‘10/59/203’]
LAT_10%NDR: [‘10/26/93’, ‘10/32/148’]
tc02-64B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 2866393.15624 pps (2x 1433196.57812 pps)
FINAL_BANDWIDTH: 1.92621620099 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/940/1103’, ‘30/930/1116’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1299371.65625 pps (2x 649685.828125 pps)
FINAL_BANDWIDTH: 15.9874688585 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/652/1001’, ‘30/645/976’]
LAT_50%NDR: [‘20/93/375’, ‘20/93/333’]
LAT_10%NDR: [‘20/33/155’, ‘20/35/166’]
tc04-1518B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1324457.375 pps (2x 662228.6875 pps)
FINAL_BANDWIDTH: 16.296123542 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/2325/2528’, ‘20/2337/2643’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-IMIX-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 2285898.6875 pps (2x 1142949.34375 pps)
FINAL_BANDWIDTH: 6.83636094713 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc06-IMIX-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 2233809.0625 pps (2x 1116904.53125 pps)
FINAL_BANDWIDTH: 6.68057824335 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 5073800.09376 pps (2x 2536900.04688 pps)
FINAL_BANDWIDTH: 3.40959366301 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/79/195’, ‘30/89/214’]
LAT_50%NDR: [‘10/50/169’, ‘10/56/168’]
LAT_10%NDR: [‘10/29/96’, ‘10/28/95’]
tc08-64B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 6148458.73438 pps (2x 3074229.36719 pps)
FINAL_BANDWIDTH: 4.1317642695 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘40/115/210’, ‘30/170/334’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/97/266’, ‘20/116/296’]
LAT_50%NDR: [‘20/45/178’, ‘20/47/173’]
LAT_10%NDR: [‘20/30/156’, ‘20/32/169’]
tc10-1518B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/154/595’, ‘30/169/695’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-IMIX-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 4239259.625 pps (2x 2119629.8125 pps)
FINAL_BANDWIDTH: 12.6782123388 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc12-IMIX-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 4682021.4375 pps (2x 2341010.71875 pps)
FINAL_BANDWIDTH: 14.0023653209 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 5654696.65624 pps (2x 2827348.32812 pps)
FINAL_BANDWIDTH: 3.79995615299 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/53/125’, ‘20/72/173’]
LAT_50%NDR: [‘10/38/125’, ‘10/45/139’]
LAT_10%NDR: [‘10/24/79’, ‘10/23/81’]
tc14-64B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 7658789.79688 pps (2x 3829394.89844 pps)
FINAL_BANDWIDTH: 5.1467067435 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘30/90/180’, ‘40/154/259’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/125/143’, ‘20/150/178’]
LAT_50%NDR: [‘20/41/135’, ‘20/47/155’]
LAT_10%NDR: [‘20/31/135’, ‘20/32/124’]
tc16-1518B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 10GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1625486.0 pps (2x 812743.0 pps)
FINAL_BANDWIDTH: 19.999979744 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/128/159’, ‘20/162/194’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-IMIX-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 5281052.125 pps (2x 2640526.0625 pps)
FINAL_BANDWIDTH: 15.7938664143 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc18-IMIX-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 10GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 5827993.1875 pps (2x 2913996.59375 pps)
FINAL_BANDWIDTH: 17.429584804 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage

7.1.6.8. 40ge2p1xl710-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrpdrdisc

RFC2544: Packet throughput L2BD test cases with vhost

  • [Top] Network Topologies: TG-DUT1-DUT2-TG 3-node circular topology with single links between nodes.
  • [Enc] Packet Encapsulations: Eth-IPv4 for L2 switching of IPv4.
  • [Cfg] DUT configuration: DUT1 and DUT2 are configured with L2 bridge- domain and MAC learning enabled. Qemu Guest is connected to VPP via vhost-user interfaces. Guest is running DPDK testpmd interconnecting vhost-user interfaces using 5 cores pinned to cpus on NUMA1 and 2048M memory. Testpmd is using socket-mem=1024M (512x2M hugepages), 5 cores (1 main core and 4 cores dedicated for io), forwarding mode is set to io, rxd/txd=256, burst=64. DUT1, DUT2 are tested with 2p40GE NIC XL710 by Intel.
  • [Ver] TG verification: TG finds and reports throughput NDR (Non Drop Rate) with zero packet loss tolerance or throughput PDR (Partial Drop Rate) with non-zero packet loss tolerance (LT) expressed in percentage of packets transmitted. NDR and PDR are discovered for different Ethernet L2 frame sizes using either binary search or linear search algorithms with configured starting rate and final step that determines throughput measurement resolution. Test packets are generated by TG on links to DUTs. TG traffic profile contains two L3 flow-groups (flow-group per direction, 253 flows per flow-group) with all packets containing Ethernet header, IPv4 header with IP protocol=61 and static payload. MAC addresses are matching MAC addresses of the TG node interfaces.
  • [Ref] Applicable standard specifications: RFC2544.
Name Documentation Message
tc01-64B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 40GE linerate, step 10kpps.
FINAL_RATE: 2765117.1875 pps (2x 1382558.59375 pps)
FINAL_BANDWIDTH: 1.85815875 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/106/231’, ‘30/98/232’]
LAT_50%NDR: [‘10/61/217’, ‘10/59/188’]
LAT_10%NDR: [‘10/24/92’, ‘10/31/139’]
tc02-64B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 40GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 2948125.0 pps (2x 1474062.5 pps)
FINAL_BANDWIDTH: 1.98114 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/909/1069’, ‘30/921/1102’]
LOSS_ACCEPTANCE: 0.5 percentage
tc03-1518B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 40GE linerate, step 10kpps.
FINAL_RATE: 1289220.34375 pps (2x 644610.171875 pps)
FINAL_BANDWIDTH: 15.8625671095 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/391/818’, ‘20/394/710’]
LAT_50%NDR: [‘10/119/525’, ‘10/116/516’]
LAT_10%NDR: [‘10/29/123’, ‘10/33/174’]
tc04-1518B-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 40GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 1320176.9375 pps (2x 660088.46875 pps)
FINAL_BANDWIDTH: 16.243457039 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/1034/1515’, ‘20/1032/1491’]
LOSS_ACCEPTANCE: 0.5 percentage
tc05-IMIX-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 40GE linerate, step 5kpps. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 1937692.10938 pps (2x 968846.054688 pps)
FINAL_BANDWIDTH: 5.79499115011 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc06-IMIX-1t1c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 1 thread, 1 phy core, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 40GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 2257307.46094 pps (2x 1128653.73047 pps)
FINAL_BANDWIDTH: 6.75085411966 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc07-64B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 40GE linerate, step 10kpps.
FINAL_RATE: 5876250.0 pps (2x 2938125.0 pps)
FINAL_BANDWIDTH: 3.94884 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘30/98/168’, ‘20/117/276’]
LAT_50%NDR: [‘10/61/158’, ‘10/63/219’]
LAT_10%NDR: [‘10/26/160’, ‘10/35/160’]
tc08-64B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 40GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 6095859.375 pps (2x 3047929.6875 pps)
FINAL_BANDWIDTH: 4.0964175 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘50/116/301’, ‘60/193/344’]
LOSS_ACCEPTANCE: 0.5 percentage
tc09-1518B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 40GE linerate, step 10kpps.
FINAL_RATE: 2465570.90624 pps (2x 1232785.45312 pps)
FINAL_BANDWIDTH: 30.3363844304 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/137/307’, ‘20/173/406’]
LAT_50%NDR: [‘10/62/244’, ‘10/65/286’]
LAT_10%NDR: [‘10/27/128’, ‘10/29/164’]
tc10-1518B-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 40GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 2806093.4375 pps (2x 1403046.71875 pps)
FINAL_BANDWIDTH: 34.526173655 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/233/529’, ‘20/462/705’]
LOSS_ACCEPTANCE: 0.5 percentage
tc11-IMIX-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 40GE linerate, step 5kpps. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 4079114.96484 pps (2x 2039557.48242 pps)
FINAL_BANDWIDTH: 12.1992730461 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc12-IMIX-2t2c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 2 threads, 2 phy cores, 1 receive queue per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 40GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 4654422.59766 pps (2x 2327211.29883 pps)
FINAL_BANDWIDTH: 13.9198263913 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage
tc13-64B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 64 Byte frames using binary search start at 40GE linerate, step 10kpps.
FINAL_RATE: 5839648.4375 pps (2x 2919824.21875 pps)
FINAL_BANDWIDTH: 3.92424375 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘10/55/138’, ‘20/75/188’]
LAT_50%NDR: [‘10/39/133’, ‘10/47/150’]
LAT_10%NDR: [‘10/25/102’, ‘10/28/127’]
tc14-64B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 64 Byte frames using binary search start at 40GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 7706328.125 pps (2x 3853164.0625 pps)
FINAL_BANDWIDTH: 5.1786525 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/48/184’, ‘20/79/278’]
LOSS_ACCEPTANCE: 0.5 percentage
tc15-1518B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for 1518 Byte frames using binary search start at 40GE linerate, step 10kpps.
FINAL_RATE: 3022789.59376 pps (2x 1511394.79688 pps)
FINAL_BANDWIDTH: 37.1924031616 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘20/131/272’, ‘20/183/330’]
LAT_50%NDR: [‘10/62/238’, ‘10/88/258’]
LAT_10%NDR: [‘10/30/186’, ‘10/34/182’]
tc16-1518B-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for 1518 Byte frames using binary search start at 40GE linerate, step 10kpps, LT=0.5%.
FINAL_RATE: 3425225.3125 pps (2x 1712612.65625 pps)
FINAL_BANDWIDTH: 42.143972245 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘20/284/427’, ‘30/415/703’]
LOSS_ACCEPTANCE: 0.5 percentage
tc17-IMIX-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-ndrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find NDR for IMIX_v4_1 frame size using binary search start at 40GE linerate, step 5kpps. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 4430691.85156 pps (2x 2215345.92578 pps)
FINAL_BANDWIDTH: 13.2507223126 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_50%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LAT_10%NDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
tc18-IMIX-4t4c-eth-l2bdbasemaclrn-eth-2vhost-1vm-pdrdisc
[Cfg] DUT runs L2BD switching config with 4 threads, 4 phy cores, 2 receive queues per NIC port.
[Ver] Find PDR for IMIX_v4_1 frame size using binary search start at 40GE linerate, step 5kpps, LT=0.5%. IMIX_v4_1 = (28x64B; 16x570B; 4x1518B)
FINAL_RATE: 5836999.39844 pps (2x 2918499.69922 pps)
FINAL_BANDWIDTH: 17.4565193786 Gbps (untagged)
LATENCY usec [min/avg/max]
LAT_100%PDR: [‘-1/-1/-1’, ‘-1/-1/-1’]
LOSS_ACCEPTANCE: 0.5 percentage